Nuttall Flexeserve Hub User manual
FLEXESERVE® | Flexeserve Hub® - North America | Quick Start Guide │ V1 DEC 2020 | 40003232 Page | 1 of 2
Flexeserve® Customer Support
[t] Call Toll-Free 833 955 8300
[e] [email protected]
Flexeserve Hub® - North America
For full details on how to operate this equipment
safely, please refer to the Operation manual.
WARNING
In an emergency, switch off the appliance and isolate
fully from the mains supply.
CAUTION
The internal surfaces will become hot, reaching
temperatures above 158°F (70°C).
Operation
Heating
Each of the model variants are supplied with a mains power switch and a controller. The controls are located
behind the front panel at the top of Flexeserve Hub®.
Set the mains power switch to the ‘I’ position and the controller will illuminate. The display will show the
current temperature. The equipment will begin to heat and reach the established temperature set-point
automatically, generally 185°F (85°C). To switch off the unit, set the power switch to the ‘OFF’ position.
Adjusting Temperatures
To view the temperature of the unit, press the ‘temperature’ button for half a second, and then release. To
change the temperature of the unit, press and hold the ‘temperature’ button and press the arrow buttons to
increase (▲) or decrease (▼) the temperature. When the ‘temperature’ button is released, the new value is
stored.
Power switch
I = On position
O = Off position
Controller display
Temperature
button
Temperature
adjustment
QUICK START GUIDE
FLEXESERVE HUB® - NORTH AMERICA
FLEXESERVE® | Flexeserve Hub® - North America | Quick Start Guide │ V1 DEC 2020 | 40003232 Page | 2 of 2
Flexeserve® Customer Support
[t] Call Toll-Free 833 955 8300
[e] [email protected]
Display and Merchandising
All items placed in Flexeserve Hub® should be in the correct packaging/containers, in line with in-store
procedures and best practice. Ensure that the door is fully closed once the products have entered the display
area.
Troubleshooting
Some faults must only be investigated by a trained and qualified Engineer. For assistance with
troubleshooting this equipment, please refer to the Operation manual or contact Customer Support.
Fault Cause Solution
Temperature display is blank.
Over-temperature thermostat has
operated. Contact Customer Support.
Controller is faulty.
Unit is not operating.
No power. Check that the isolation switch
is switched on.
Fuse has tripped.
Contact Customer Support.
Over-temperature thermostat has
operated.
Mains circuit breaker of the store
has tripped. Check store procedures.
Lights are not working. Light unit has failed. Contact Customer Support.
Alarm is sounding. Door has been left open. Ensure door is closed properly.
Daily Cleaning
For full details on how to clean this equipment, please refer to the Operation manual.
The wire shelves can be removed and cleaned by unhooking from the shelf brackets. To clean the brackets,
lift out of the slotted posts.
Once the wire shelves are removed, crumbs and debris can removed from the unit. Take care not to sweep
crumbs into the air outlet at the front of the unit. Internal and external surfaces can be cleaned using non-
abrasive cleaning products. Ensure that all parts are refitted before use of the unit.
Wire shelves
and brackets
Slotted post
with wire
shelf and
brackets
Other Nuttall Heated Shelf manuals
Popular Heated Shelf manuals by other brands
Hatco
Hatco GRS Series Installation and operating manual
Hatco
Hatco Glo-Ray GRSR-19 Replacement parts list
Hatco
Hatco HGSM Series Installation and operating manual
Buffalo
Buffalo CW147 instruction manual
Metro DataVac
Metro DataVac C175 Series user manual
Hatco
Hatco GLO-RAY GRSSR20-DL Series Installation & operating manual
Flexeserve
Flexeserve Zone MK2 2 Tier quick start guide
Marshall AIR
Marshall AIR NN4A owner's manual
Giani
Giani GCETW39AL-1 instruction manual
Hatco
Hatco HGSM-1P Installation and operating manual
Eagle
Eagle Heated Drawers Operating manual and instructions
Bathroom Butler
Bathroom Butler LOFT TWIN 6 Bar Assembly, Mounting and User Instructions