Numens 460 Series User manual
460 non-addressable manual call point
Installation Instructions
www.numens.com 1 32-0014-r07_2017-10
Cautions
ELECTRICAL HAZARD: Disconnect power from equipment prior to making
any internal adjustments. Service should only be performed by qualified
personnel.
FRAGILE: Inspect the equipment prior to installation. Do not install the
equipment if damage is apparent. Do not attempt to disassemble this
equipment. If damaged, return to the supplier.
ELECTROSTATIC HAZARD: This is sensitive electronic equipment. Apply
safe ant-static practices when handling this equipment.
CIRCUIT LIMITATIONS: The maximum number of devices connected to a
single alarm zone is limited by the control and indicating equipment, and
may be limited by local regulations.
Introduction
460 manual call points connect to non-addressable fire detection
control and indicating equipment, or to addressable fire detection
control and indicating equipment that can accept non-addressable
devices
1
.
These instructions provide trained installation personnel with
details to install and commission 460 manual call points for
optimum performance.
Preparation
Before commencing installation, ensure all equipment and tools to
mount and connect the equipment are available, such as drills,
mounting screws, cables and ladders.
NOTE: The unit comes separated from the back-box, ready for installation.
However, if necessary, separate the front face from the body by inserting
the reset key and gently pulling the lower portion of the front face down and
away from the body. Removing the operating element will expose the
screws that hold the body to the back-box (see Figs. 3 ~ 5).
Installation
Back-box
1. Feed the conductors through the rear of the back-box.
2. Securely mount the back-box to the wall surface using fixing
screws and wall plugs. Fig. 1 shows the back-box mounting
hole dimensions.
Fig. 1: Back-box dimensions
NOTE: Where the 460-009 weather proof enclosure accessory is used, the
back-box is not used.
Wiring
The terminals accept (0.4 ~ 2.5) mm
2
conductors.
1. Strip the conductor insulation to expose 5 mm of the
conductor.
2. Connect the conductors to the terminals as shown in Fig. 2.
WARNING: Take care to ensure the insulation does not get
clamped by the terminal contact.
1
May be used with the 620-002 contact monitor module.
Fig. 2a: 460-001 to 460-004 wiring connections
Fig. 2b: 460-005 wiring connections
Fig. 2c: 460-006 wiring connections
3. Check the wiring for continuity, short circuits and earth faults.
Assembly
1. Separate the front face from the body by inserting the reset
key and gently pulling the lower portion of the front face
down from the body (see Fig. 3).
Fig. 3: Separate the front face from the body
2. Remove the operating element (see Fig. 4).
Fig. 4: Operating element
87
87
36
36
470Ω
OR
460-004
470Ω
460-003
470Ω
OROROROR
87651234
567 84321
470Ω
+
_
+
_
460-001 460-002
_
+
_
+
+/_
_
+/+/_
_
+/
+/_
_
+/+/_
_
+/
OR
8765
4321
OR
_
+/ _
+/
+/_+/ _
_
+/
_
+/ +/_
+/_
AND
AND
1234 8765
4321 5678
OR OR
PRESS HERE
PRESS HERE
PRESS HERE
PRESS HERE
PRESS HEREPRESS HERE
2 32-0014-r07_2017-10
Numens
9 Xizhao Road, Innovative Industrial Area, Dong Qian Lake, Ningbo, Zhejiang, China 315121
© 2015 ~ 2017 Ambest Electronics (Ningbo) Co Ltd. All rights reserved. All specifications and other information shown were current at the date of
publication and sub
j
ect to chan
g
e without notice.
3. Screw the body to the back-box with the CS3 x 30 screws
supplied (see Fig. 5).
NOTE: Where the 460-009 weather proof enclosure accessory is
used, the body is screwed to the metal mounting bracket in the
weather proof enclosure.
Fig. 5: Body and back-box fixing screws
4. Replace the operating element (see Fig. 6)
Fig. 6: Replacing the operating element
5. Clip the front face onto the body (see Fig. 7).
Fig. 7: Replacing the front face
6. If necessary, set the displacement element to the normal
position using the key supplied.
Commissioning
Manual Call Point
1. Ensure all the alarm signal services, releasing devices and
extinguisher systems are disabled during the commissioning
period.
2. Connect power to the manual call point.
3. Operate the displacement element with finger pressure.
4. Check that an alarm condition occurs at the control and
indicating equipment.
5. For 460-002 and 460-003 models, check that the red alarm
LED indicator illuminates.
6. Reset the manual call point displacement element to the
normal position using the key supplied.
7. Reset the control and indicating equipment.
Final Conditions
Ensure all the alarm signal services, releasing devices and
extinguisher systems disabled for the commissioning are returned
to their previous condition.
References
Document Description
31-0022 460 non-addressable manual call points datasheet
View the complete range of products at
www.numens.com
PRESS HERE
PRESS HERE
PRESS HEREPRESS HERE
This manual suits for next models
6
Other Numens Fire Alarm manuals
Popular Fire Alarm manuals by other brands
Zeta Alarm Systems
Zeta Alarm Systems INFINITY ID2 installation manual
System Sensor
System Sensor 22051TLE-RF-26 Installation and maintenance instructions
Pittway
Pittway Notifier AM2020 troubleshooting guide
Ampac
Ampac ZoneSense user manual
Kidde
Kidde VM-1 Technical reference manual
LST
LST SIM016-3 Specification sheet
