Numatic TTB-455 User manual
TWINTEC 455
TTB 455 OPERATION - INFORMATION INDEX
1. Part Identification Diagram
2. Basic Operation Instructions
3. Dos and Donts
4. Fitting The Brush / Dri e Board
5. Filling The Clean Water Tank
6. Water Release Controls
7. Adjusting The Handle Height
8. Handle Controls
9. Emptying The Top Tank
10. Emptying The Bottom Tank
11. Cleaning The Separator Filter
12. Cleaning The Top Tank Filter
13. Cleaning The Bottom Tank Filter
14. Daily Maintenance Routine
15. Charging The Batteries
16. Changing The Squeegee Blades
17. Problem Sol ing
TWINTEC 455
TTB 455 OPERATION - PART IDENTIFICATION
HANDLE TOP (DIRTY
WATER) TANK
BOTTOM (CLEAN
WATER) TANK
SEPARATOR
SQUEEGEE TOOL
BRUSHES
CHASSIS
BRUSH
DECK
CHARGING
LEAD
TWINTEC 455
TTB 455 OPERATION - OPERATING INSTRUCTIONS
1. Ensure that charging lead has been disconnected
2. Ensure that the isolator pin is in place
3. Fit pad & drive board / scrubbing brush
4. Unclip deck so that the pad / brush is positioned flat to the floor
5. Lower the squeegee blade so that it is positioned flat to the floor
6. Fill bottom tank with clean water and detergent
7. Ensure that water on/off control is set at appropriate position
8. Ensure that top tank(s) are empt
9. Ensure that separator is fitted correctl
10. Adjust handle height to suit
11. Stand behind the machine
12. Press both of the black rubber buttons on the handle displa
13. Press and hold in the ellow button on the rear of the handle and at the same
time squeeze the triggers on the handle. Release the ellow button
14. Push the machine in the direction in which ou want to clean, holding in the black
triggers
15. When ou want the machine to stop, release triggers
TWINTEC 455
TTB 455 OPERATION - DOS AND DONTS
DO ensure onl competent persons unpack and assemble the machine
DO keep the machine clean
DO keep the brushes in good condition
DO replace an worn or damaged parts immediatel
DO ensure that the working area is clear of obstructions
DO ensure that the working are is well illuminated
DO follow all the instructions supplied
DO ensure that if using a pad, it is washed after each use
DONT use steam cleaners or pressure washers to clean the machine
DONT use the machine outdoors in the rain
DONT attempt machine maintenance or cleaning with the isolator pin intact
DONT allow an inexperienced repairs
DONT leave the brush or pad on the machine when not in use
DONT allow the machine to be used b inexperienced or unauthorised personnel
DONT lift or pull the machine b an of the operating triggers
DONT leave the machine running in one spot, turn off if not being used
DONT leave the brush or pad on the machine overnight, the will flatten
WARNING
It is essential that the equipment is correctl assembled and operated in accordance
with current safet regulations. When using the equipment alwa s ensure that all
necessar precautions are taken to guarantee the safet of the operator and an other
persons who ma be affected. Wear non-slip footwear when scrubbing. Alwa s use a
respirator mask in dust environments. The use of other accessories ma affect the
safet of the scrubber dr er. A full range of brushes and other accessories are available
from Numatic International.
TWINTEC 455
TTB 455 OPERATION - FITTING THE BRUSH / DRIVE BOARD
1. MACHINE SHOWN WITH
BRUSHES. 2. POSITION BRUSH ONTO
THE GEARBOX WITH THE 3
INDENTATIONS ALLIGNING
WITH THE 3 TABS. TURN
ANTI-CLOCKWISE TO LOCK
THE BRUSH IN PLACE.
3. THE BRUSHES WILL NOW
BE LOCKED IN PLACE AND
READY FOR USE.
NOTE: WHEN USING A DRIVE BOARD FOLLOW THE SAME INSTRUCTIONS
TO FIT DRIVE BOARD AND THEN FIX PAD CENTRALLY ONTO BOARD.
TTB 455 OPERATION - PROBLEM SOLVING
MACHINE NOT PICKING UP WATER
CHECK - SQUEEGEE BLADES ARE NOT WORN
CHECK - SQUEEGEE IS TOUCHING FLOOR
CHECK - HOSE IS CONNECTED TO SQUEEGEE
CHECK - HOSE IS CONNECTED TO SUCTION DOME
CHECK - SUCTION DOME IS SECURED TO TOP TANK
CHECK - HOSE FROM SUCTION DOME IS CONNECTED TO VAC MOTOR
NO WATER GOING ONTO FLOOR
CHECK - WATER CONTROL IS TURNED ON - SEE HANDLE CONTROLS PAGE
CHECK - WATER TAP IS TURNED ON - SEE WATER ON / OFF PAGE
CHECK - CLEAN WATER TANK IS NOT EMPTY
MACHINE ONL RUNS FOR SHORT PERIODS
CHECK - MACHINE HANDLE IS POSITIONED AT WAIST HEIGHT
CHECK - BATTERIES ARE FULLY CHARGED
TWINTEC 455
TWINTEC 455
TTB 455 OPERATION - CHANGING THE SQUEEGEE BLADES
1. REMOVE THE SQUEEGEE
TURN UPSIDE DOWN, AND
REMOVE THE 4 SCREWS
ALONG THE CENTRE OF THE
TOOL.
2. LIFT AND REMOVE THE 2
PLASTIC INSERTS AND DIS-
CARD THE WORN BLADES.
3. PLACE THE NEW BLADES
INTO POSITION WITH THE
RIBBED SIDES FACING OUT-
WARD. ENSURE THAT THE
BLADES OVERHANG EQUALLY
AT EACH END.
4. ALLIGN PLASTIC INSERTS
AND APPLY PRESSURE UNTIL
YOU FEEL THE BLADE GRIP
INTO PLACE. REPLACE
SCREWS AND PUT SQUEEGEE
BACK ONTO MACHINE.
NOTE:
REPLACEMENT SQUEEGEE BLADE PART NUMBER: 217213
TWINTEC 455
TTB 455 OPERATION - CHARGING THE BATTERIES
1. LIFT THE FLAP ON THE
MACHINE HANDLE AND
INSERT CHARGING LEAD.
2. PLUG THE CHARGING
LEAD INTO A STANDARD
230 or 110 VOLT SOCKET.
NOTE:
WHEN THE MACHINE IS CHARGING YOU WILL BE ABLE TO HEAR THE
COOLING FAN. THIS WILL AUTOMATICALLY SWITCH OFF WHEN THE
MACHINE IS FULLY CHARGED.
BATTERY CHARGE TIME: 8 HOURS
TWINTEC 455
TTB 455 OPERATION - DAILY MAINTENANCE ROUTINE
1. RINSE THE BRUSHES WITH
CLEAN WATER ON A DAILY
BASIS.
2. RINSE THE SQUEEGEE ON
A DAILY BASIS AND REMOVE
ANY DEBRIS.
3. RINSE DIRTY WATER TANK
WITH CLEAN WATER AND
EMPTY AS NORMAL.
4. IF MACHINE IS NOT TO BE
USED FOR MORE THAN 2
DAYS, RINSE AND EMPTY
THE CLEAN WATER TANK.
Other Numatic Floor Machine manuals
Numatic
Numatic floorcare tt 1840 User manual
Numatic
Numatic NR-1500M User manual
Numatic
Numatic TT 345 User manual
Numatic
Numatic TT-3450S User manual
Numatic
Numatic TTB 4055/100 User manual
Numatic
Numatic FloorCare TGB 1840 Reference guide
Numatic
Numatic TTB-345 User manual
Numatic
Numatic LOLINE HLL 332 User manual
Numatic
Numatic TTB 4055 User manual
Numatic
Numatic CleanTec NHL 15 Hi&Lo User manual
Numatic
Numatic LoLine NLL 332 User manual
Numatic
Numatic HNS1550 User manual
Numatic
Numatic NR 1500 User manual
Numatic
Numatic TTB 4055/100 User manual
Numatic
Numatic ET 4045 User manual
Numatic
Numatic NuSpeed NR-1500 User manual
Numatic
Numatic TwinTec 455 User manual
Numatic
Numatic ET 4045 User manual
Numatic
Numatic HFS 1015 User manual
Numatic
Numatic TTV-5565/200T Assembly instructions
