Numatic TTB-345 User manual
TWINTEC 345
TTB 345 OPERATION - INFORMATION INDEX
1. Part Identification Diagram
2. Basic Operation Instructions
3. Dos and Donts
4. Fitting The Brush / Dri e Board
5. Filling The Clean Water Tank
6. Water Release Controls
7. Adjusting The Handle Height
8. Handle Controls
9. Emptying The Top Tank
10. Emptying The Bottom Tank
11. Cleaning The Separator Filter
12. Cleaning The Top Tank Filter
13. Cleaning The Bottom Tank Filter
14. Daily Maintenance Routine
15. Charging the Batteries
16. Changing The Squeegee Blades
17. Problem Sol ing
TWINTEC 345
TTB 345 OPERATION - PART IDENTIFICATION
HANDLE
TOP (DIRTY
WATER) TANK
BOTTOM (CLEAN
WATER) TANK
SEPARATOR
SQUEEGEE TOOL
BRUSH
CHASSIS
SPLASH
SKIRT
TWINTEC 345
TTB 345 OPERATION - OPERATING INSTRUCTIONS
1. Ensure that charging lead has been disconnected
2. Ensure that the isolator pin is in place
3. Fit pad & drive board / scrubbing brush
4. Unclip deck so that the pad / brush is positioned flat to the floor
5. Lower the squeegee blade so that it is positioned flat to the floor
6. Fill bottom tank with clean water and detergent
7. Ensure that water on/off control is set at appropriate position
8. Ensure that top tank(s) are empt
9. Ensure that separator is fitted correctl
10. Adjust handle height to suit
11. Stand behind the machine
12. Press both of the black rubber buttons on the handle displa
13. Press and hold in the ellow button on the rear of the handle and at the same
time squeeze the triggers on the handle. Release the ellow button
14. Push the machine in the direction in which ou want to clean, holding in the black
triggers
15. When ou want the machine to stop, release triggers
TWINTEC 345
TTB 345 OPERATION - DOS AND DONTS
DO ensure onl competent persons unpack and assemble the machine
DO keep the machine clean
DO keep the brushes in good condition
DO replace an worn or damaged parts immediatel
DO ensure that the working area is clear of obstructions
DO ensure that the working are is well illuminated
DO follow all the instructions supplied
DO ensure that if using a pad, it is washed after each use
DONT use steam cleaners or pressure washers to clean the machine
DONT use the machine outdoors in the rain
DONT attempt machine maintenance or cleaning with the isolator pin intact
DONT allow an inexperienced repairs
DONT leave the brush or pad on the machine when not in use
DONT allow the machine to be used b inexperienced or unauthorised personnel
DONT lift or pull the machine b an of the operating triggers
DONT leave the machine running in one spot, turn off if not being used
DONT leave the brush or pad on the machine overnight, the will flatten
WARNING
It is essential that the equipment is correctl assembled and operated in accordance
with current safet regulations. When using the equipment alwa s ensure that all
necessar precautions are taken to guarantee the safet of the operator and an other
persons who ma be affected. Wear non-slip footwear when scrubbing. Alwa s use a
respirator mask in dust environments. The use of other accessories ma affect the
safet of the scrubber dr er. A full range of brushes and other accessories are available
from Numatic International.
TWINTEC 345
TTB 345 OPERATION - FITTING THE BRUSH / DRIVE BOARD
1. MACHINE SHOWN WITH
SCRUB RING AND BRUSH. 2. PLACE SCRUB RING OVER
RIM ON MACHINE DECK.
3. POSITION BRUSH ONTO
THE GEARBOX WITH THE 3
INDENTATIONS ALLIGNING
WITH THE 3 TABS. TURN
ANTI-CLOCKWISE TO LOCK
THE BRUSH IN PLACE.
4. THE BRUSH WILL NOW
BE LOCKED IN PLACE AND
READY FOR USE.
NOTE: WHEN USING A DRIVE BOARD FOLLOW THE SAME INSTRUCTIONS
TO FIT DRIVE BOARD AND THEN FIX PAD CENTRALLY ONTO BOARD.
TWINTEC 345
TTB 345 OPERATION - FILLING THE CLEAN WATER TANK
1. SIMPLY POUR WATER
WITH A MIX OF YOUR CHO-
SEN DETERGENT INTO THE
SPOUT ON THE FRONT OF THE
BOTTOM TANK.
TWINTEC 345
TTB 345 OPERATION - WATER RELEASE CONTROLS
1.THE WATER CONTROL IS
LOCATED AT THE REAR OF
THE MACHINE (BOTTOM LH)
2. WITH THE TAP IN ITS
HORIZONTAL POSITION
THERE WILL BE NO WATER
FLOW.
3.IN ORDER TO RELEASE
WATER, PUSH TAP TOWARDS
THE FLOOR.
NOTE:
FULL WATER FLOW IS 2.5
LITRES PER MINUTE. THIS
TAP CAN BE ADJUSTED ANY-
WHERE BETWEEN NO FLOW
AND FULL FLOW TO ACHIEVE
THE DESIRED FLOW FOR THE
TASK BEING UNDERTAKEN.
TWINTEC 345
TTB 345 OPERATION - ADJUSTING THE HANDLE HEIGHT
1. SQUEEZE THE HANDLE
ADJUSTMENT LEVER ON
THE RIGHT HAND SIDE.
2. OPERATION IS EASIEST
WITH THE HANDLE AT WAIST
HEIGHT.
3. FOR TURNING IN TIGHT
SPACES OR FOR LESS FLOOR
PRESSURE, PUT THE HANDLE
INTO A HIGHER POSITION.
NOTE:
THE BEST WAY TO SCRUB IS
TO FIND A HANDLE LEVEL AT
WHICH YOU FEEL COMFORT-
ABLE AND CAN EASILY CON-
TROL THE MACHINE AROUND
CORNERS AND OBSTACLES
AS WELL AS IN A STRAIGHT
LINE.
THE HIGHER THE HANDLE
LEVEL, THE LESS FLOOR
PRESSURE AND VICE VERSA.
TWINTEC 345
TTB 345 OPERATION - HANDLE CONTROLS
WATER ON / OFF VACUUM ON / OFF
WATER
ON
BATTERY
FULLY
CHARGED
BATTERY
CLOSE
TO EMPTY
BATTERY
EMPTY
VACUUM
ON
BRUSH
ON
BRUSH
OFF
Table of contents
Other Numatic Floor Machine manuals
Numatic
Numatic Nacecare TT 1117 / 100 User manual
Numatic
Numatic TwinTec 455 User manual
Numatic
Numatic HFS 1015 User manual
Numatic
Numatic TTB 1840 User manual
Numatic
Numatic TWINTEC BATTERY ETB4045 Installation and operation manual
Numatic
Numatic NHL 15 User manual
Numatic
Numatic floorcare tt 1840 User manual
Numatic
Numatic ET 4045 User manual
Numatic
Numatic Henry PET User manual
Numatic
Numatic TTB 4550/100 ST User manual
Numatic
Numatic NuSpeed NR-1500 User manual
Numatic
Numatic HNS1550G User manual
Numatic
Numatic LoLone NLL Series Assembly instructions
Numatic
Numatic NV-450 User manual
Numatic
Numatic TTV-5565/200T Assembly instructions
Numatic
Numatic TWINTEC CABLE TT4055 Installation and operation manual
Numatic
Numatic CRO 8055 User manual
Numatic
Numatic TRO 650 User manual
Numatic
Numatic SPN 1804 User manual
Numatic
Numatic LoLine User manual
