NSS PREDATOR CXC150 User manual

PREDATOR CXC150

IMPORTANT SAFETY INSTRUCTIONS

READ AND UNDERSTAND ALL INSTRUCTIONS

BEFORE OPERATING OR SERVICING MACHINE

DANGER!

Failure to ObserveThese Instructions Can Cause Personal Injury

to Machine Operator, By-standers or Possible Machine Damage.

SAVE THESE INSTRUCTIONS

•NEVER attempt to service or perform maintenance functions while machine is plugged into an electrical

outlet.

•ALWAYS unplug machine before attempting to service the motorized brush attachment.

•NEVER operate in standing water. NEVER expose to rain. ALWAYS store indoors.

•NEVER overfill recovery tank or allow water to enter vacuum standpipe.This will cause damage to the

vacuum motor and possible electrocution.

•NEVER operate machine with a cut, abraded or taped cord.

•NEVER operate machine with a broken grounding blade on the plug.

•ALWAYS replace the entire cord when the cord or plug is damaged in any manner.

•NEVER handle the machine, cord or plug with wet hands.

•NEVER drop or insert any object into any machine opening.

•ALWAYS keep face, fingers, hair or any other body part, or loose clothing away from any machine

opening or any moving part, particularly the revolving brush.

•NEVER leave the machine unattended when plugged in. Unplug the machine from the electrical outlet

when not in use.

•ALWAYS turn the machine off before unplugging it from the electrical outlet.

•NEVER operate this machine in the presence of flammable or combustible liquids or fumes.

• When any electrical motor, switch, cord or plug service is required, maintenance should only be done by

an authorized service station, an electrician or other qualified persons.

•NEVER operate this machine if it is not working properly, if it as been dropped, damaged, exposed to

weather, or dropped into water. Return the machine to a service center for examination and repair.

•NEVER operate this machine with any air opening blocked. Keep all air openings free of dust, lint, hair,

ect.

•NEVER operate this machine without solution tank filter screens or vacuum standpipe filter screen in

place or if they are clogged. Clean all filter screens after every use.

•ALWAYS store this machine indoors. Protect it from rain or snow.

•NEVER spray the top of the machine with liquids.

•DO NOT pull or carry this machine by the electrical supply cord, use the cord as a handle, close a door on

the cord, pull the cord around sharp edges or corners, or expose to heated surfaces.

•NEVER disconnect the plug by pulling on the cord.To disconnect the cord from the outlet grasp the plug,

not the cord.

•ALWAYS unplug this machine before attempting to service.

•ALWAYS use a defoamer which will prevent a buildup of foam in the recovery tank. If a defoamer is not

used, the motor can be damaged from shampoo being pulled into the vacuum motor.

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INFORMATION & OPERATING INSTRUCTIONS

DO NOT OPERATE MACHINE UNTIL YOU HAVE READ THIS SECTION

IMPROPER USE OF THE PREDATOR CXC150 WILL VOID THE WARRANTY

1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.

2. To keep fitting and lines from damage during freezing conditions, use an

anti-freeze in the pump and heater or keep equipment inside heated areas.

3. Do not let pump run dry.

4. Use neutral pH, water-based products only - NO SOLVENTS!

INSPECTION:

Carefully unpack and inspect the PREDATOR CXC150 for shipping damage. Each unit is

tested and inspected before shipment. Any damage incurred is the responsibility of the carrier,

who should be notified immediately.

CLEANING SOLUTIONS:

We recommend liquid cleaning chemicals. Powders may be used, but unless mixed very

thoroughly, they could cause build-up in the lines, pump, quick-disconnects, etc. A pH of 7-9 is

strongly recommended to avoid premature pump wear, which would void the warranty.

MAINTENANCE:

For optimum performance, flush the machine with clear water at the end of each working day.

Once a month, minimum, run a flushing compound through the machine to cut any alkaline

build-up that may have formed.

Lubricate wheels, casters and hinges as needed. The pump and vacuum motors do not require

any maintenance.

The body can be cleaned with a general all-purpose detergent and protected with a silicone

type product like Armor All®.The quick-disconnects should be lubricated with silicone, also.

Prior to each job, inspect the holding tank filter and the recovery tank float filter for hair and dirt.

The drain valve should also be inspected regularly and kept free of any debris or build-up.

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

SET-UP:

Fill the holding tank with clear water and the detergent of your choice. Mix well.The addition of

warm or hot water to the holding tank would be a plus factor.

1. Plug in the cord. (This cord runs the pump and vacuums).

2. Turn on the pump and spray through the cleaning tool for a few seconds to fill the lines with

solution.

BALL FLOAT VACUUM SHUTOFF:

When the recovery tank is full, the ball float system will shut off the incoming air flow and

prevent water from entering the vac motors.The float will not work in heavy foam. Always use a

defoamer to prevent overflow. Once the float is activated, the vac switches must be turned off

and the recovery tank emptied.

CAUTION: To avoid vac motor damage, always make sure the filter is clean and the float

travels freely before turning on the machine. Use a defoamer whenever foam is present.

Water damage to the vac motors is not covered by the warranty.

SAFETY PRECAUTIONS:

All extension cords must have a rating of at least 12/3 (#12 cord). Extension cords should be

no longer than 50 feet. Replace the plug immediately if the ground prong becomes damaged

or is broken off.The ground is necessary for safety.

VACUUM SWITCH (1 & 2 :

Each switch turns on one vac motor. Turn both switches

on for maximum lift. The vac switches illuminate when

turned on.

PUMP SWITCH (3 :

This switch will illuminate when the pump is on.

(3)

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

ITEM # PART # DESCRIPTION ITEM # PART # DESCRIPTION

#1 4091231 Drain Gate

#1A 4093041 Spout, for Drain Gate

#2 4090581 Screw, 10-32 X 5/8, S/S

#3 4091251 Latch

#4 4091161 O-Ring, Thin

#4A 4091171 O-Ring, Thick

#4B 4090701 Nut, Cast Aluminum

#5 4093191 Vacuum Tank, Black, specify model

#6 4091241 Hose Barb, 1-1/2”, plastic

#7 4091291 PVC Elbow, 1-1/2”

#8 4091391 Gasket, for Vacuum Dome

#9 4091581 Vacuum Dome

#10 4091571 Vac Shut-off, manifold Assy.

#10A 4091501 Ball & Cage

#11 4090701 Nut, Cast Aluminum

#12 4091171 O-Ring, Thick

#13 4091291 PVC Elbow, 1-1/2”

#14 4091121 Hose Clamp, size 28

#15 4093131 Hose, Rubber, 2”X 24”

#15A 4093141 Hose, Rubber, 2”X 13”

#16 4090691 Washer, Vulcanized Fiber

#16A 9122470 Washer, Brass,1”OD X9/16ID X 1/16”

#17 4093091 Nipple, !/4 p.t., S/S

#17A 4091611 Bushing, Vulcanized Fiber

#18 4093171 Stop Chain, 12”

#19 4091181 Split Ring

#20 9120930 3/16 Flat Washer, ZP

#21 9120900 1/4-20 Hex Nut, w/Ny-Lok, ZP

#22 4091211 Vacuum Motor, 2-stage

#23 4091431 Gasket, Vac Motor

#24 4091651 Manifold, Vacuum, #3 or #4

#25 4090631 1/4-20 X 5”Hex Bolt

#26 9120930 3/16 Flat Washer, ZP

#27 9120920 1/4 Hex Nut, Finish

#28 4091651 Manifold, Vacuum, #3 or #4

#29 9120900 1/4 Hex Nut, w/Ny-Lok, ZP

#30 4091401 Chrome Handle

#31 4090601 1/4-20 x 3/4 Screw, Flathead Philips

#32 4091031 Quick Disconnect, male, 1/4 p.t.

#33 4091411 Exhaust Flange

#34 4091311 Louver, 3”(includes 3 screws)

#35 4091261 Latch Strike

#36 4091081 Elbow, Brass, 1/4 pt 90

#37 4091331 PVC Reducer

#38 4091151 Cord Retainer w/Strain Relief

#39 4093211 Axle, 1/2”X 17-1/2”

#40 4091361 Wheel, 8 inch, non-marking

#41 4091021 Axle Cap

#42 9120900 1/4 Hex Nut, Ny-Lok, ZP

#43 4091141 Axle Bracket

#44 4090611 1/4-20 X 3/4”Hex Bolt, ZP

#45 4094041 Base, Black (specify model)

#46 4093051 Castor, 4”swivel

#47 4093181 Holding Tank, Black (specify model)

#48 4092031 Hose Barb, Brass

#49 4091191 Filter, Pump Inlet, 40 mesh, S/S

#50 4093201 Lid, with label (no hinges)

#51 4091131 Hose Clamp, 3/8 - 7/8

#52 4093071 Pump, (no fittings), 150 PSI

#53 4091101 Hose Barb & Elbow, Plastic

#54 4093021 Hose Barb, Straight, Plastic

#55 4093121 Hose, Pump Inlet, 3/8”X 13”

#56 4091541 Hose, Pump Outlet, 3/8”X 48”

#57 4090091 Switch Plate (empty), CXH150

#58 4090511 #4 X 3/8”” Screw, Panhead, S/S

#59 4091041 Switch, SPST, Covered, w/light

#60 4093011 Hose Barb

#61 4093151 Funnel, Black

#62 4090541 6-32 X 2”Screw, Panhead, S/S

#63 4090531 6-32 Hex Nut with Ny-Lok

#64 4091441 Cooling Fan, 100 CFM

#65 4091451 Fan Guard

#66 4090071 Label, NSS

#67 4091611 Gasket

#68 4091521 Cord Wrap, Black

#69 4090671 3/8 Acorn Nut, Nickle Plate

#70 1391161 Washer, Plastic 5/8OD X 3/8ID X 1/16

MISCELLANEOUS ASSEMBLIES/PARTS

4091461* Thermistor Control Kit w/Potentiometer

& Probe

4091471* Thermistor Control Kit w/Potentiometer,

Probe & Cutout

4093161 Drain Gate Assembly, complete with

O-Ring & Nut

(NOTE: Items in kits not sold separately.)

PREDATOR CXC150

PARTS LIST

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

PREDATOR CXC150

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

COMMON STAINS AND CLEANINGTREATMENTS

TREATMENT METHODS

First: Remove excess material by blotting to absorb liquids, or by scraping with a dull edge

(butter knife) is a solid.

Second: Clean the remaining stain as directed by the chart below. Always follow the direction

on the container. Apply the cleaning material directly to the stain (avoid over wetting

the carpet or upholstery), then remove the loosened stain material with a white ab-

sorbent cloth or tissue.

Third: When the carpet is dry, gently brush the carpet pile to restore its appearance.

Note: Treat unknown stains with a volatile solvent first and follow with other agents as re-

quired. If you are uncertain of the effect of the cleaning agent on the carpet fiber or

dye, test on an inconspicuous area first.

STAINTYPE TREATMENT MATERIAL

Asphalt Volatile solvent/detergent

Beer Liquid detergent, White vinegar

Berry stain Liquid detergent, Ammonia 3-6%, Water

Bleach Liquid detergent, Water

Blood (dried) Warm detergent, Ammonia 3-6%, Water

Blood (wet) Liquid detergent, Water

Butter Volatile solvent

Catsup or Mustard Liquid detergent

Chewing gum Volatile solvent

Chocolate Liquid detergent, Ammonia water

Coffee Detergent, White vinegar, Volatile solvent

Cola drink Liquid detergent

Creme de Menthe (green) Liquid detergent

Egg (raw) Liquid detergent

Food dye Liquid detergent, Water

Furniture dye or polish Paint/Oil/Grease remover, Detergent

Gravy Liquid detergent

Lipstick Paint/Oil/Grease remover

Mascara Paint remover, Volatile solvent, Detergent, Water

Milk Liquid detergent

Orange drink Liquid detergent, Water

Shoe polish Heated iron into clean towel, Volatile solvent

Tea Liquid detergent

Tomato Juice Liquid detergent

Urine Liquid detergent, Water

Vomit Warm detergent, Water, White vinegar

Wine Liquid detergent, Ammonia 3-6%, Water, Vinegar

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

6/27/01

FAN

BLACK

BLUE

WHITE

VAC 2

VAC 1

ORANGE

WHITE

BLACK

GROUND

WHITE

VACUUM

PUMP

CORD 1

PREDATOR CXC150

WIRING DIAGRAM

120V & 240V

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

PREDATOR CXC150 ORIG 05-00 9094008 WHW REV. B 08-01

NSS ENTERPRISES, INC.

3115 Frenchmens Road, Toledo, Ohio 43607

PHONE: 419-531-3761 ■FAX: 419-531-3761

NSS®Enterprises, Inc. European Distribution Centre

Unit II, Pinfold Trading Estate 55 Nottingham Road

STAPLEFORD, NOTTINGHAM NG9 8AD ENGLAND U.K.

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

Table of contents

Popular Floor Machine manuals by other brands

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Instructions for use

Numatic

Numatic ET 4045 Owner's instructions

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE manual

Mytee

Mytee 8070 Mytee-Lite instructions

Kärcher

Kärcher B 140 R manual

Triple S

Triple S Ace 26T1 user guide

Nilfisk-Advance

Nilfisk-Advance SW 750 Service manual

Tornado

Tornado Marathon 2000 98190 Operation & maintenance manual

Windsor

Windsor ADMIRAL Admiral 8 Specifications

Numatic

Numatic TTB 1117/100 Owner's instructions

Tennant

Tennant 8210D Operator's manual

Nobles

Nobles Frontier Operator and parts manual

lavina

lavina 21-X user manual

KENT

KENT Edge 28B Service manual

Tennant

Tennant 215 Operator and parts manual

Windsor

Windsor BDP 51/2000C operating instructions

CleanFreak

CleanFreak DURA-18HD Operator's manual

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST How-to guide