NSB FAN JUMBO User manual

INSTRUCTION MANUAL

JUMBO / BIANCA

CEILING FAN

SAFETY PRECAUTION

IMPORTAN: PLEASE READ BEFORE INSTALLATION

1. Installation must be carried out by a qualified wiring installer

2. Turn off the electrical mains at the circuit breaker fuse box

3. Use power supply 220-240V/50Hz.

4. The ceiling mounting must be able to with hold a min of 16kg.

5. Install ceiling fan blade more than 2.3 M above floor.

6. Do not place any objects in the path of the blades.

7. When all electrical connection is done, store all wire neatly.

8. Make sure that all screws and connection are tightly screwed and secured.

9. This appliance is not intended for use by persons (including children) with Reduced physi-

cal, sensory or mental capabilities, or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the appliance by a person responsi-

ble for their safety. Children should be supervised to ensure that they do not play with the

appliance.

10. his appliance can be used by children aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or lack of experience and knowledge if they

have been given supervision or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by

children without supervision.

11. An all‐pole disconnection must be incorporated in the fixed wiring in accordance with the

wiring rules, a all‐pole disconnection incorporated in the fixed wiring is to be provided.

PARTS & ACCESSORIES

1 Mounting bracket x 1

2 Fan motor assembly x 1

3 Fan blade bracket x 1

4 Fan bladesx 3

5 Fan blades fixing cap x 3

6 Fan blades screw x 9 (and 1 spare)

7 Wire Nut x 3

8 Expansion screws x 2

9 Remote receiver x 1 set

10 Remote transmitter x 1 set

ROTATE

TURBO

MED

LOW

OFF

Fig.1

FAN INSTALLATION INSTRUCTION

The fan must be installed so that the lowest point of the fan blade must be 2.3m from the floor.

NOTE: The lowest point of the fan blade is when the fan head is adjusted to 45°.

The ceiling fan must be installed in a location so that the blades are a minimum 1M spacing

from the tip of the blade to the nearest objects or walls.

Fig. 2

Foor

Wall or any

other object

＞2.3M

＞1M

WARNING: Make sure electricity off at the main power box before commencing work.

• Install the hanging bracket to the ceiling joist or structure that is capable of carrying a load of

at least 16kg, with the two long screws(expansion screws) provided.(3)

• Remove the key pin from the side of hanging bracket.(4)

• Lift the fan assembly onto the mounting bracket, put the holes of down rod and plug aligning

the hanging bracket holes, Make sure to tighten the key pin to prevent the fan from falling .(5)

All electrical connections must be in accordance with local and national electrical code

standards. If you are unfamiliar with proper electrical wiring connections obtain the

services of a qualified electrician.

• Make the wire connection L, N, and Rotate to the remote receiver as shown the diagram

below in Fig. 6

• Carefully insert the Remote Receiver above the hanger ball in the remainder spacing in the

mounting bracket. Take care not to damage or loosen any of the wiring Fig. 7

INSTALLATION OF THE MOUNTING BRACKET

ELECTRICAL WIRING DIAGRAM

Hanging bracket

Expansion screws

Key pin Key pin

Plastic plug

Down rod

TO MOTOR N Remote

Receiver

TO MOTOR N

Quick connector for

infra red sensor

Infra red sensor

for remote control

TO MOTOR L

FOR ROTATE

FOR ROTATE AC IN L

220-240V/50Hz

Power supply

AC IN N

Fig.3

Fig.6

Fig.7

Fig.4 Fig.5

CANOPY ASSEMBLY

• After completing electrical connection, cover the MOUNTING BRACKET with the CANOPY.

• Ensure that all electrical wiring is carefully tucked inside the canopy.

• Locate 2 screws on underside of mounting bracket.

• Attach canopy to the mounting bracket by placing screws into slotted holes in canopy.

• Twist clockwise to lock into place. Tighten screws firmly.

Fig.8

Screws

• Align the 3 mounting holes on the blade (3) to the 3 mounting holes of the blade bracket (2);

• Insert the fixing cap (4) into the mouting holes from the bottom of the blade (3) and secure

by tightening the 3 screws (1) from the top of the blade bracket (2).

• Once completed, repeat the same process on the remaining blades.

• Install the assembled fan-blades (7) to the motor part (5).

• Tighten the 2 set screws (6) on the side of the motor shaft.

NSTALLATION OF THE FAN BLADES

(1)

(2)

(3)

(4)

(5)

(6)

(7)

Fig.9

Fig.10

• Loosen the two set screws on both sides of the motor; (Fig.11)

• Rotate the fan head and aim the arm screw at the desired angle (There are only three angles

available: 0°, 45°, 90°.They are labelled on the motor part) (Fig.12)

• Retighten the set screws after adjusting to the desired angle. Ensure the set screws are

tighten and postioned well into the slot of the desired angle. (Fig.13)

ADJUSTMENT OF THE FAN HEAD

45 degree Horizontal 90 degree

Vertical 0 degree

Arm Screws

Set Screws

Arm

Screws

Fig.11

Fig.12

Fig.13

Due to fan’s natural movement, connections may get loose after a period of usage.

To ensure a proper and safety usage, We are highly recommended to inspect and

tighten all connections every 6 months.

CLEANING

Clean your fan periodically to prolong its new appearance. Basic cleaning procedures are as

follows:

1. Use only lukewarm water. Do not use detergent, corrosive or acidic solution.

2. Damp the cloth lightly. Use only soft or lint-free cloth to clean the fan. Rough fabric will

scratches the surface.

3. Apply a thin coat of furniture polish to the wooden blades will protect and enhance the

appearance.

4. To cover small scratches, apply a light coat of shoe polish over it.

5. There is no need to lubricant the fan.

MAINTENANCE

TROUBLESHOOTING

Check on the following before lodging a service report.

SYMPTOM

PROBLEM

SOLUTION

Fan not moving

•

Main cables not connected

•

Wire connection loose

Fan noisy

Remote control

Not working

•

Housing screws are loose

•

Wire and nut connections rattles

against each other.

•

Canopy touches the ceiling.

•

Tighten all screws

•

Separate and store neatly the

wire connections from the nut.

•

Check to ensure the canopy is

not touching or too close to the

Ceiling.

•

Check main and branch

circuit breakers or fuse.

•

Check the line wires connec-

tions to the fan and switch

housing.

•

Remote and receiver code different

•

Battery not installed

•

Weak battery

• Check that the codes to ensure

exactly the same.

• Install the remote control

battery

This manual suits for next models

Table of contents

Other NSB FAN Fan manuals

NSB FAN

NSB FAN TEEGA User manual

NSB FAN

NSB FAN CUPID Installation and operating instructions

NSB FAN

NSB FAN XTRA User manual

NSB FAN

NSB FAN FA701 User manual

NSB FAN

NSB FAN MOORE User manual

NSB FAN

NSB FAN Veera User manual

NSB FAN

NSB FAN ANISE Installation and operating instructions

NSB FAN

NSB FAN Ovio+ 60 User manual

NSB FAN

NSB FAN NEO User manual

NSB FAN

NSB FAN ALOHA User manual

NSB FAN

NSB FAN Jaya Deluxe User manual

NSB FAN

NSB FAN KELLY Installation and operating instructions

NSB FAN

NSB FAN X LED User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual