Notifier ID50 SERIES Instruction sheet

ID50/60 installation,

commissioning &

configuration

manual

997-263, Issue 4 September 2002

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Contents

i 997-263, Issue 4

Se tember 2002

Contents

1 Introduction 1

1.1 Manual Purpose 1

1.2 System Design and Planning 1

1.3 General 2

1.3.1 Date-dependent Functions 2

1.4 CE Marking 3

1.5 EN54 unctions 3

1.6 Ancillary unctions 4

1.7 Related Documents 5

1.8 Warnings and Cautions 5

1.9 Tips 5

1.10 Glossary of Icons 6

2 Installation Guide 7

2.1 How to Use this Section 7

2.2 Pre-Installation Check List 7

2.1.1 Some Panel DOs and DONTs 7

2.3 Transient Protection 8

2.4 Product Inspection 9

2.4.1 Chec ing Your Panel for Damage 9

2.4.2 What to do if Panel is Damaged

or Suspect 10

2.5 Dismantling the Panel 11

2.5.1 Removing the Cover 11

2.5.2 Removing the Panel Electronics 12

2.5.3 Bac Box Fixing 13

2.5.4 Semi-Flush Mounting Bezel (Optional) 14

2.6 Assembling the Panel 15

2.7 RS485 Communications Link 16

2.7.1 Fitting the RS485 Interface Module PCB 17

2.8 RS232 Interface Connections 18

3 Cabling 19

3.1 Cabling Instructions 19

3.1.1 Cable Terminations 20

3.2 Cabling Installation Notes 21

3.2.1 Introduction 21

3.2.2 Quality of Cable and of Cable Installation 21

3.3 EMC Considerations 22

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Contents

ii997-263, Issue 4

Se tember 2002

3.3.1 Screen Termination 22

3.3.2 Ferrite Sleeves (Optional) 22

3.4 MICC Cables 22

4 Commissioning 23

4.1 Introduction 23

4.2 Preliminary Checks 23

4.3 Internal Checks 24

4.3.1 Jumper Lin Options 24

4.4 External Wiring Checks 25

4.4.1 Loop Wiring 26

4.4.2 RS485 Communications Lin 27

4.4.3 DC Auxiliary Output 27

4.4.4 Sounder Circuit Outputs 28

4.4.5 CFG Outputs C and D 29

4.4.6 -VE Outputs 30

4.4.7 Digital / ÜE Inputs 30

4.4.8 Switch Connections 30

4.5 Powering the Panel 31

4.5.1 Start-up Language Selection 31

4.5.2 Batteries 32

4.6 Configuration and Handover 33

4.7 Commissioning Tests 34

4.7.1 Test LEDs 34

4.7.2 Test LCD 34

4.7.3 Test Zones 34

4.7.4 Test Auto High Test 34

4.7.5 Test Outputs 34

4.7.6 Test Buzzer 34

4.7.7 Test Keyboard 34

4.8 Sensors and Modules 35

4.8.1 EN54 Requirements 35

4.8.2 Loop Wiring Testing 35

5 Configuration 36

5.1 Introduction 36

5.2 Navigation and Number Entry 36

5.3 Level 2 Configuration Options 36

5.4 Level 3 Configuration Options 37

5.5 Setup Options 38

5.5.1 Language 38

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Contents

iii 997-263, Issue 4

Se tember 2002

5.5.2 Date Format 39

5.5.3 Primary/Extend Delay Timers 39

5.5.4 Extinguishing System Delay 40

5.5.5 Extinguishing System Soa 40

5.5.6 Hold Switch Operation 41

5.5.7 Device Blin ing 41

5.5.8 Pulse On/Off Ratio 42

5.5.9 Service Phone Number 42

5.5.10 Site Name 43

5.5.11 Control Keys 43

5.5.12 RS232 Protocol 44

5.5.13 Print Control or Third Party 44

5.5.14 Repeater Protocol 45

5.5.15 Number of Repeaters 46

5.5.16 Transmission Device 46

5.5.17 FW4Input Disable 46

5.5.18 Digital Input 1 47

5.5.19 Day Mode Activity 48

5.5.20 Wee end Night Mode 49

5.5.21 Auto High Test 49

5.5.22 Diagnostic Mode 50

5.5.23 VdS Compatibility 50

5.6 Circuit Options 51

5.6.1 Signalling Line Circuit (SLC) - Devices 51

5.6.2 Signalling Line Circuit (SLC) - Learn 59

5.6.3 On-Board Circuits 60

5.7 Control-By-Event Output Rules 62

5.7.1 Output Type 65

5.7.2 Filter-by-type 66

5.7.3 Evacuation 67

5.7.4 Silence 67

5.7.5 Interrupt Delay 68

5.7.6 Class Change 68

5.7.7 Two Zone 69

5.7.8 Zones 70

5.7.9 Device Inputs 71

5.7.10 Soa Timer 72

5.8 Zone Texts 72

5.9 Access Options 74

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Contents

iv997-263, Issue 4

Se tember 2002

5.10 System Options 75

5.10.1 Crystal Frequency 75

5.10.2 Wipe Memory 76

5.11 Normal 76

Appendix 1 - Specification A1-1 to A1-6

Appendix 2 - ID60 Single Loop Panel

Differences A2-1 to A2-5

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

1 997-263, Issue

September 2002

1 Introduction

1.1 Manual Purpose

This purpose of this manual is to provide the user with

all recommended procedures and full technical details

for the successful installation, commissioning and

programming of a NOTIFIER ID50 Series Panel.

The descriptions and procedures also apply to the

NOTIFIER ID60 panel. Differences between the ID50 and

ID60 panels are given in Appendix 2.

Procedures described in this manual include appropriate

warnings and cautions to guide the user towards adopting

safe and methodical work practices during the installation,

commissioning and programming phases.

Important Note

This manual must be read, and its content clearly

understood, before proceeding with any work relating to

the ID50 Series Panel. Damage to the control panel may

result from NOT following the recommended procedures

described in this manual.

This manual provides all necessary instructions for the

ID50 Series Panel and applies only to fire panels fitted

with compatible software.

CAUTION: In particular, care must be taken when

powering up down any repeaters.

If there are any areas of doubt, consult your supplier

before continuing with the system installation,

commissioning and programming.

1.2 System Design and Planning

It is assumed that the system, of which the ID50 Series

Panel equipment is a part, has been designed by a

competent fire alarm system designer in accordance with

the requirements of EN5 Part 1 and any other local

codes of practice that are applicable.

The design drawings should clearly show the positions

of all the ID50 Series Panel control equipment and field

devices.

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

2997-263, Issue

September 2002

1.3 General

The ID50 Series Panel is designed for use with

NOTIFIERs range of addressable analogue sensors,

control and monitoring modules and addressable call

points. A unique signalling protocol is used, having digital

address and control signals and analogue pulse width

monitoring for the reply data from devices.

The serial communications interface operates under

RS 85 protocol and enables communications between

the fire panel and repeaters.

While every effort is made to ensure the accuracy of the

content of this manual, the manufacturer reserves the

right to change the information without notice.

Installation

The ID50 Series Panel is easy to install providing the

recommended procedures described in this manual are

followed. To avoid inadvertent contamination of the PCB

Assembly, the manufacturer recommends it be installed

in the back box only after all other trades have completed

their tasks.

Commissioning

To commission the ID50 Series Panel, follow the

recommended procedures described in this manual. The

manufacturer recommends that during commissioning

and maintenance, ALL RS 85 signal cables are

disconnected at the Panel end, BEFORE powering down

the system and are connected AFTER powering up the

system.

Configuration

To configure the panel and system, carefully read and

follow the procedures given in this manual. These

procedures describe the menus that are displayed on

the Liquid Crystal Display (LCD) Unit.

Refer to the ID50 Series Operating manual (ref: 997-

26 ) for a description of compatible addressable

Signalling Loop Circuit (SLC) analogue devices.

1.3.1 Date-dependent Functions

The calendar end date for this product is 31/12/2063

(two thousand and sixty-three) and it will perform correctly

up to this date.

The calendar function has not been tested beyond

this date.

Only fit the electronics

module after all the other

trades have completed

their tasks!

Only suitably-qualified

engineers must install,

commission and

configure this product

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

3 997-263, Issue 4

Se tember 2002

1.4 CE Marking

This anel is CE Marked to show that it conforms to the

requirements of the following Euro ean Community

Directives:

nElectromagnetic Com atibility Directive 89/336/EEC

(and the amending Directives 92/31/EEC, 93/68/EEC)

nLow Voltage Directive 73/23/EEC (and the amending

Directive 93/68/EEC).

1.5 EN54 Functions

This fire control anel is designed to com ly with the

requirements of EN54 Part2/4:1997. In addition to the

basic requirements of EN54-2, the anel may be configured

to conform with the following o tional functions - the

a licable clauses of EN54-2 are referenced as follows:

Options Clause

Indications:

Fault signals from points 8.3

Recording of the number of entries

into fire alarm condition 7.13

Controls:

Coincidence detection 7.12

Dela of the immediate actioning of outputs 7.11

Disablement of each address point 9.5

Test condition 10

Outputs:

Fire alarm device(s) (Sounders) 7.8

Fire alarm routing equipment 7.9

Fire protection equipment 7.10

Fault warning routing equipment 8.9

(requires monitoring b fault routing equipment)

The following features are rovided by the Power Su ly

Unit (PSU) of the ID50 Series Panel to com ly with

EN54-4.

Features of the ID50 EN54-4

Power Supply Unit (PSU Clause

Derive power from the mains suppl 5.1

Derive power from a standb batter source 5.2

Charge and monitor the standb

batter /batteries 5.3

Detect and signal various PSU faults 5.4

ID50 Series Panel - Installation, Commissioning & Configuration Manual

Introduction

4997-263, Issue 4

Se tember 2002

1.6 Ancillary Functions

The following is a list of ancillary functions that are

rovided by the ID50 Series anel in addition to the those

required by EN54-2/4. These functions are described in

the section of this manual as referenced (exce t those

marked thus * which are described in 997-264-XXX,

ID50 Series Panel-Operating Manual):

Ancillary Manual

Functions Section Refs.

Site Specific Setup Options 5.5

Access Options 5.9

Voltage Indications *4.11.7

Control-b -Event 5.7

Output modes 5.7.1

Input t pe pattern 5.7.9

Disable/enablement *4.9

Repeater interface 2.7

Self-learn configuration - manual 5.6.1

Self-learn configuration - auto 5.6.2

Module supervision options 5.6.1

Module silence options 5.7.4

Text editing 5.8

Sensor LED blinking on/off 5.5.7

Bell pulsing ratio 5.5.8

Displa of alarm count *4.11.6

Extend dela timer 5.5.3

Sounder Volt-free contact options 4.4.5

Rela drive output option 4.4.6

Extinguishing s stem features 5.5.4, 5.5.5, 5.5.6,

5.7.1

Other manuals for ID50 SERIES

This manual suits for next models

Table of contents

Other Notifier Fire Alarm manuals

Notifier

Notifier NBG-12LO User manual

Notifier

Notifier IFS-2600 Instruction Manual

Notifier

Notifier ONYX Series User manual

Notifier

Notifier NBG-12LA User manual

Notifier

Notifier AFP-300 Owner's manual

Notifier

Notifier FS-WST Instruction Manual

Notifier

Notifier AFP-100 User manual

Notifier

Notifier ACS Series User manual

Notifier

Notifier CAB-5 Technical manual

Notifier

Notifier NBG-12LX User manual

Notifier

Notifier NAM-232 User manual

Notifier

Notifier AM2020 User manual

Notifier

Notifier UZC-256 User manual

Notifier

Notifier LCD-80F User manual

Notifier

Notifier NFS-3030/E Owner's manual

Notifier

Notifier 1010 User manual

Notifier

Notifier NFS-640 Owner's manual

Notifier

Notifier IFS-2600 Technical manual

Notifier

Notifier 002-439 Instruction Manual

Notifier

Notifier AFC-600 User manual

Notifier

Notifier ID50 SERIES User manual

Notifier

Notifier NBG-12LX User manual

Notifier

Notifier AFP-2800 User manual

Notifier

Notifier NBG-12LOB User manual

Popular Fire Alarm manuals by other brands

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 installation manual

System Sensor

System Sensor 22051TLE-RF-26 Installation and maintenance instructions

Pittway

Pittway Notifier AM2020 troubleshooting guide

Ampac

Ampac ZoneSense user manual

Kidde

Kidde VM-1 Technical reference manual

LST

LST SIM016-3 Specification sheet

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Owner's Manual & Installation Instructions

bolid

bolid S2000-IP-03 instruction manual

GST

GST DI-9204 Installation

E2S

E2S BExTBG05D instruction manual

Fire-Lite Alarms

Fire-Lite Alarms MS-2 instructions

Siemens

Siemens FDOOT221 Technical manual

hyfire

hyfire HY5000 Series install guide

FlameStop

FlameStop PFSIFP8 Installation and operation manual

Radionics

Radionics Radionics 9124 user guide

UniPOS

UniPOS FD 7120 instruction manual

FIREWOLF

FIREWOLF FW-C01224 owner's manual

Siemens

Siemens MH-5 Series Installation instructions manual