Nordson Encore HD Reference guide

EncorerHD

Manual Powder Spray Gun

Customer Product Manual

Part 1604869-13

Issued 09/19

NORDSON CORPORATION •AMHERST, OHIO •USA

For parts and technical support, call the

Industrial Coating Systems Customer Support Center

at (800) 433-9319 or contact your local Nordson representative.

This document is subject to change without notice.

Check http://emanuals.nordson.com/finishing for the latest version

and available local languages.

Part 1604869-13 E2018 Nordson Corporation

Nordson Corporation welcomes requests for information, comments, and

inquiries about its products. General information about Nordson can be

found on the Internet using the following address:

http://www.nordson.com.

Address all correspondence to:

Nordson Corporation

Attn: Customer Service

555 Jackson Street

Amherst, OH 44001

Notice

This is a Nordson Corporation publication which is protected by copyright.

Original copyright date 2014. No part of this document may be

photocopied, reproduced, or translated to another language without the

prior written consent of Nordson Corporation. The information contained

in this publication is subject to change without notice.

Trademarks

ColorMax, Color-on-Demand, Encore, HDLV, iControl, Prodigy, Nordson,

and the Nordson logo are registered trademarks of Nordson Corporation.

nLighten is a trademark of Nordson Corporation. All other trademarks are

the property of their respective owners.

Change Record i

Part 1604869-13

E2018 Nordson Corporation

Change Record

Revision Date Change

01 01/2014 New release

02 04/2014 New flat spray electrode holder and assembly, new conical nozzle kit and

conical electrode assembly

03 05/2014 Page 7−3, new trigger axle P/N 1605713

Page 7−5, new nozzle P/N’s

04 07/2014 New flat and conical electrode holders

05 09/2014 Re-zero procedure revised

06 12/2014 New powder inlet tube; 3mm and 4mm nozzles to ship with gun

07 10/2015 Revised equipment labels and parts

08 03/16 Added cleaning procedure

09 09/16 Nozzle part number change and positive power supply added

10 03/18 Added 1083205, Deflector to parts list and some callout and

nomenclature changes

11 04/18 Updated system setup images, updated certification label

12 03/18 Changed description for gun labels

13 07/18 Added nLighten LED inspection kit, added XD electrode support, new

reference document links and updated description for part number

1600819. Added power supply resistance test nomenclature changes

Change Record

Part 1604869-13 E2018 Nordson Corporation

Table of Contents iii

Part 1604869-13

E2018 Nordson Corporation

Table of Contents

Safety 1-1..................................................

Introduction 1-1.............................................

Qualified Personnel 1-1......................................

Intended Use 1-1...........................................

Regulations and Approvals 1-1...............................

Personal Safety 1-2.........................................

Fire Safety 1-2.............................................

Grounding 1-3..............................................

Action in the Event of a Malfunction 1-3........................

Disposal 1-3...............................................

Description 2-1.............................................

Introduction 2-1.............................................

Specifications 2-2...........................................

Equipment Labels 2-2.......................................

Applicator Certification Label 2-2...........................

Setup 3-1..................................................

System Connections 3-1.....................................

Spray Gun Installation 3-2..................................

Operation 4-1..............................................

European Union, ATEX, Special Conditions for Safe Use 4-1......

System Operation 4-2.......................................

Spray Gun Operation 4-2....................................

Changing Presets with the Settings Trigger 4-2...............

Changing Powder Flow with the Settings Trigger 4-3..........

Purging the Spray Gun 4-3................................

Electrode Air Wash Operation 4-4.............................

Daily Operation 4-4.........................................

Initial Startup 4-4.........................................

Startup 4-4..............................................

Standby Button 4-4.......................................

Changing Flat Spray Nozzles 4-5...........................

Converting from Flat Spray Nozzles to Conical Nozzles 4-6....

Changing Deflectors or Conical Nozzles 4-7..................

Installing the Optional Pattern Adjuster Kit 4-8................

Shutdown 4-8...............................................

Maintenance 4-8............................................

Recommended Cleaning Procedure for

Powder Contact Parts 4-9.................................

Maintenance Procedures 4-9...............................

Table of Contents

Part 1604869-13 E2018 Nordson Corporation

Repair 5-1.................................................

Spray Gun Repair 5-1.......................................

Display Module Replacement 5-2...........................

Display Module Removal 5-2............................

Display Module Installation 5-2...........................

Power Supply and Powder Path Replacement 5-4............

Gun Disassembly 5-4...................................

Power Supply Replacement 5-5..........................

Powder Path Removal 5-6..............................

Powder Path Installation 5-6.............................

Gun Re-Assembly 5-8..................................

Cable Replacement 5-9...................................

Cable Removal 5-9.....................................

Cable Installation 5-10...................................

Trigger Switch Replacement 5-10............................

Switch Removal 5-10....................................

Switch Installation 5-11..................................

Troubleshooting 6-1........................................

Spray Gun Power Supply Resistance Test 6-2..................

Electrode Assembly Resistance Test 6-3.......................

Gun Cable Continuity Test 6-4................................

Parts 7-1...................................................

Introduction 7-1.............................................

Reference Documentation 7-1..............................

Spray Gun Parts 7-2........................................

Spray Gun Parts List 7-3..................................

Spray Gun Options 7-4......................................

Miscellaneous Spray Gun Options 7-4.......................

nLightent7-5............................................

Flat Spray Nozzles 7-6....................................

Cross Cut Nozzles 7-6....................................

45-Degree Corner-Spray Nozzle 7-7.........................

45-Degree In-Line Flat-Spray Nozzle 7-7....................

Conical Nozzle, Deflectors and Electrode Assembly Parts 7-8...

Conical Nozzle and Deflectors 7-8........................

Conical Nozzle Kit (shipped with gun) 7-8..................

Conical Electrode Assembly 7-9..........................

XD Electrode Support 7-9..................................

Pattern Adjuster Kit 7-10...................................

Lance Extensions 7-10.....................................

Ion Collector Kit 7-10.......................................

Ion Collector Components for Lance Extensions 7-11..........

Powder Hose and Air Tubing 7-11...........................

Safety 1-1

Part 1604869-13

E2018 Nordson Corporation

Section 1

Safety

Introduction

Read and follow these safety instructions. Task- and equipment-specific

warnings, cautions, and instructions are included in equipment

documentation where appropriate.

Make sure all equipment documentation, including these instructions, is

accessible to all persons operating or servicing equipment.

Qualified Personnel

Equipment owners are responsible for making sure that Nordson equipment

is installed, operated, and serviced by qualified personnel. Qualified

personnel are those employees or contractors who are trained to safely

perform their assigned tasks. They are familiar with all relevant safety rules

and regulations and are physically capable of performing their assigned

tasks.

Intended Use

Use of Nordson equipment in ways other than those described in the

documentation supplied with the equipment may result in injury to persons

or damage to property.

Some examples of unintended use of equipment include

Susing incompatible materials

Smaking unauthorized modifications

Sremoving or bypassing safety guards or interlocks

Susing incompatible or damaged parts

Susing unapproved auxiliary equipment

Soperating equipment in excess of maximum ratings

Regulations and Approvals

Make sure all equipment is rated and approved for the environment in which

it is used. Any approvals obtained for Nordson equipment will be voided if

instructions for installation, operation, and service are not followed.

All phases of equipment installation must comply with all federal, state, and

local codes.

Safety

1-2

Part 1604869-13 E2018 Nordson Corporation

Personal Safety

To prevent injury follow these instructions.

SDo not operate or service equipment unless you are qualified.

SDo not operate equipment unless safety guards, doors, or covers are

intact and automatic interlocks are operating properly. Do not bypass or

disarm any safety devices.

SKeep clear of moving equipment. Before adjusting or servicing any

moving equipment, shut off the power supply and wait until the

equipment comes to a complete stop. Lock out power and secure the

equipment to prevent unexpected movement.

SRelieve (bleed off) hydraulic and pneumatic pressure before adjusting or

servicing pressurized systems or components. Disconnect, lock out, and

tag switches before servicing electrical equipment.

SObtain and read Safety Data Sheets (SDS) for all materials used. Follow

the manufacturer’s instructions for safe handling and use of materials,

and use recommended personal protection devices.

STo prevent injury, be aware of less-obvious dangers in the workplace

that often cannot be completely eliminated, such as hot surfaces, sharp

edges, energized electrical circuits, and moving parts that cannot be

enclosed or otherwise guarded for practical reasons.

Fire Safety

To avoid a fire or explosion, follow these instructions.

SDo not smoke, weld, grind, or use open flames where flammable

materials are being used or stored.

SProvide adequate ventilation to prevent dangerous concentrations of

volatile materials or vapors. Refer to local codes or your material SDS

for guidance.

SDo not disconnect live electrical circuits while working with flammable

materials. Shut off power at a disconnect switch first to prevent sparking.

SKnow where emergency stop buttons, shutoff valves, and fire

extinguishers are located. If a fire starts in a spray booth, immediately

shut off the spray system and exhaust fans.

SClean, maintain, test, and repair equipment according to the instructions

in your equipment documentation.

SUse only replacement parts that are designed for use with original

equipment. Contact your Nordson representative for parts information

and advice.

Safety 1-3

Part 1604869-13

E2018 Nordson Corporation

Grounding

WARNING: Operating faulty electrostatic equipment is hazardous and can

cause electrocution, fire, or explosion. Make resistance checks part of your

periodic maintenance program. If you receive even a slight electrical shock

or notice static sparking or arcing, shut down all electrical or electrostatic

equipment immediately. Do not restart the equipment until the problem has

been identified and corrected.

Grounding inside and around the booth openings must comply with NFPA

requirements for Class II, Division 1 or 2 Hazardous Locations. Refer to

NFPA 33, NFPA 70 (NEC articles 500, 502, and 516), and NFPA 77, latest

conditions.

SAll electrically conductive objects in the spray areas shall be electrically

connected to ground with a resistance of not more than 1 megohm as

measured with an instrument that applies at least 500 volts to the circuit

being evaluated.

SEquipment to be grounded includes, but is not limited to, the floor of the

spray area, operator platforms, hoppers, photoeye supports, and

blow-off nozzles. Personnel working in the spray area must be

grounded.

SThere is a possible ignition potential from the charged human body.

Personnel standing on a painted surface, such as an operator platform,

or wearing non-conductive shoes, are not grounded. Personnel must

wear shoes with conductive soles or use a ground strap to maintain a

connection to ground when working with or around electrostatic

equipment.

SOperators must maintain skin-to-handle contact between their hand and

the gun handle to prevent shocks while operating manual electrostatic

spray guns. If gloves must be worn, cut away the palm or fingers, wear

electrically conductive gloves, or wear a grounding strap connected to

the gun handle or other true earth ground.

SShut off electrostatic power supplies and ground gun electrodes before

making adjustments or cleaning powder spray guns.

SConnect all disconnected equipment, ground cables, and wires after

servicing equipment.

Action in the Event of a Malfunction

If a system or any equipment in a system malfunctions, shut off the system

immediately and perform the following steps:

SDisconnect and lock out electrical power. Close pneumatic shutoff

valves and relieve pressures.

SIdentify the reason for the malfunction and correct it before restarting the

equipment.

Disposal

Dispose of equipment and materials used in operation and servicing

according to local codes.

Safety

1-4

Part 1604869-13 E2018 Nordson Corporation

Other manuals for Encore HD

Table of contents

Other Nordson Paint Sprayer manuals

Nordson

Nordson Encore User manual

Nordson

Nordson WM-1 Reference guide

Nordson

Nordson Encore HD Reference guide

Nordson

Nordson Tribomatic 2 Reference guide

Nordson

Nordson ColorMax 2 User manual

Nordson

Nordson Trilogy GP Reference guide

Nordson

Nordson Encore LT User manual

Nordson

Nordson ColorMax 2 Reference guide

Nordson

Nordson Tribomatic Magnum User manual

Nordson

Nordson Universal Series Reference guide

Nordson

Nordson FP-200 User manual

Nordson

Nordson Encore PE User manual

Nordson

Nordson Trilogy Reference guide

Nordson

Nordson Sure Coat Series Reference guide

Nordson

Nordson Versa-Spray II Reference guide

Nordson

Nordson Prodigy Robot Gun Reference guide

Nordson

Nordson kinetix Reference guide

Nordson

Nordson Trilogy AS User manual

Nordson

Nordson ColorMax User manual

Nordson

Nordson Trilogy User manual

Nordson

Nordson SDS 40-CC Meter User manual

Nordson

Nordson Corona Cup Gun Ki User manual

Nordson

Nordson Encore PE User manual

Nordson

Nordson Encore LT Parts list manual

Popular Paint Sprayer manuals by other brands

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Operator's manual

Graco

Graco 246737 Repair and parts

Binks

Binks SV100 Service manual

Fimco

Fimco LG-4-3-1 owner's manual

AG SPRAY

AG SPRAY FS-ATV-25BL owner's manual

Bonide

Bonide 051 Operation and service instructions

zogics

zogics Z-DAS instruction manual

KISANKRAFT

KISANKRAFT KK-KBS-165 Operation manual

Matrix

Matrix SG 650 Translation of the original instructions

Anest Iwata

Anest Iwata SGA-3 Installation, use & maintenance instruction manual

paasche

paasche VV Instructions and parts list

Carlisle

Carlisle DeVilbiss JGA-510 Service manual

Gardena

Gardena 11120 Operator's manual

Conrad

Conrad Hobby Airbrush K3 operating instructions

wiwa

wiwa 14025 R/F operating manual

Graco

Graco EM 390 Instructions-parts list

DeVilbiss

DeVilbiss LUNA2i Operation manual

Graco

Graco HydroShield WMBH00 Instructions - parts