NordicTrack PathFinder User manual

Serial Number

Decal

USERʼS MANUAL

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. eep this manual

for future reference.

QUESTIONS?

f you have questions, or if parts are

damaged or missing, DO NOT

CONTACT THE STORE; please

contact Customer Care.

IMPORTANT: Please register this

product (see the limited warranty

on the back cover of this manual)

before contacting Customer Care.

CALL TOLL-FREE:

1-888-825-2588

Mon.–Fri. 6 a.m.–6 p.m. MT

Sat. 8 a.m.–4 p.m. MT

ON THE WEB:

www.nordictrackservice.com

www.nordictrack.com

Model No. NTEL00909.2

Serial No.

Write the serial number in the

space above for reference.

TABLE OF CONTENTS

WARNNGDECALPLACEMENT ..............................................................2

MPORTANTPRECAUTONS ................................................................3

BEFOREYOUBEGN ......................................................................4

ASSEMBLY ...............................................................................5

HOWTOUSETHEELLPTCAL .............................................................12

MANTENANCEANDTROUBLESHOOTNG ...................................................20

EXERCSEGUDELNES ...................................................................22

PARTLST ..............................................................................23

EXPLODEDDRAWNG ....................................................................25

ORDERNGREPLACEMENTPARTS ..................................................BackCover

LMTEDWARRANTY ..............................................................BackCover

WARNING DECAL PLACEMENT

NordicTrack is a registered trademark of CON P, nc.

This drawing shows the location(s) of the warning

decal(s). If a decal is missing or illegible, see

the front cover of this manual and request a

free replacement decal. Apply the decal in the

location shown. Note: The decal(s) may not be

shown at actual size.

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical before using your elliptical. ICON

assumes no responsibility for personal injury or property damage sustained by or through the use

of this product.

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over age 35 or per-

sons with pre-existing health problems.

2. Use the elliptical only as described in this

manual.

3. It is the responsibility of the owner to ensure

that all users of the elliptical are adequately

informed of all precautions.

4. The elliptical is intended for home use only.

Do not use the elliptical in a commercial,

rental, or institutional setting.

5. eep the elliptical indoors, away from mois-

ture and dust. Place the elliptical on a level

surface, with a mat beneath it to protect the

floor or carpet. Make sure that there is at

least 3 ft. (0.9 m) of clearance in the front

and rear of your elliptical and 2 ft. (0.6 m) on

each side.

6. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

7. eep children under age 12 and pets away

from the elliptical at all times.

8. The elliptical should not be used by persons

weighing more than 350 lbs. (159 kg).

9. Wear appropriate clothes while exercising;

do not wear loose clothes that could become

caught on the elliptical. Always wear athletic

shoes for foot protection while exercising.

10. Hold the handlebars or the upper body arms

when mounting, dismounting, or using the

elliptical.

11. The pulse sensor is not a medical device.

Various factors may affect the accuracy of

heart rate readings. The pulse sensor is

intended only as an exercise aid in determin-

ing heart rate trends in general.

12. eep your back straight while using the ellip-

tical; do not arch your back.

13. Over exercising may result in serious injury

or death. If you feel faint or if you experience

pain while exercising, stop immediately and

cool down.

14. The elliptical does not have a freewheel; the

pedals will continue to move until the fly-

wheel stops. Reduce your pedaling speed in

a controlled way.

IMPORTANT PRECAUTIONS

BEFORE YOU BEGIN

Thank you for selecting the revolutionary NordicTrack®

PATHF NDER elliptical. The PATHF NDER elliptical

provides an impressive selection of features designed

to make your workouts at home more effective and

enjoyable.

For your benefit, read this manual carefully before

you use the elliptical. f you have questions after

reading this manual, please see the front cover of this

manual. To help us assist you, note the product model

number and serial number before contacting us. The

model number and the location of the serial number

decal are shown on the front cover of this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Pulse Sensor

Cushion Cylinder

Upper Body Arm

Handlebar

Pedal Disc

Wheel

Pedal

Water Bottle Holder*

Console

Handle

Leveling Foot *Water bottle is not included

Ramp

Reset/Off

Switch

Access Cover

Pedal Arm Latch

Latch Button

Power Cord

ASSEMBLY

Assembly requires two persons. Place all parts of the elliptical in a cleared area and remove the packing

materials. Do not dispose of the packing materials until assembly is completed.

In addition to the included tool(s), assembly requires a Phillips screwdriver , an adjustable

wrench , and a rubber mallet .

As you assemble the elliptical, use the drawings below to identify small parts. The number in parentheses below

each drawing is the key number of the part, from the PART L ST near the end of this manual. The number fol-

lowing the parentheses is the quantity needed for assembly. Note: If a part is not in the hardware kit, check

to see if it has been preassembled.

M8 Split

Washer (103)–4

M8 Washer

(95)–8

M6 Washer

(112)–8

Wave Washer

(118)–2

M4 x 16mm

Screw (106)–8

M8 x 16mm Patch

Screw (102)–16

M8 x 25mm Patch

Screw (121)–2

M6 x 50mm

Patch Screw (62)–4

M10 x 95mm Patch Screw (100)–4

M6 x 12mm Patch

Screw (111)–4

Have a second person hold the Folding Frame

(2) to prevent the elliptical from tipping until this

step is completed.

Attach the Rear Stabilizer (4) to the Folding

Frame (2) with two M10 x 95mm Patch Screws

(100).

Next, hold the handle on the Rear Stabilizer (4),

press the Latch Button (67), and unfold the

elliptical so that the Rear Stabilizer is resting on

the floor.

2. Orient the Front Stabilizer (3) so that the small

welded tubes are facing away from the Main

Frame (1).

Attach the Front Stabilizer (3) to the Main Frame

(1) with two M10 x 95mm Patch Screws (100).

100

Handle

Welded

Tubes

To make assembly easier, read the

information on page 5 before you begin.

100

4. Apply a generous amount of the included

grease to the Upright Axle (48) and to two Wave

Washers (118).

Tip: Avoid damaging the Wire Harness (60).

nsert the Upright Axle (48) through the Upright

(5) and center it. Slide a Wave Washer (118)

onto each side of the Upright Axle.

Next, identify the Right and Left Upper Body

Legs (6, 7), which are marked with “Right” and

“Left” stickers, and orient them as shown.

Slide the Right and Left Upper Body Legs (6, 7)

onto the right and left sides of the Upright Axle

(48).

Tighten an M8 x 16mm Patch Screw (102) and

an M8 Washer (95) into each end of the Upright

Axle (48).

Avoid damaging

the Wire

Harness (60)

3. Orient the Upright (5) as shown. Have a second

person hold the Upright near the Main Frame

(1).

Locate the wire tie in the Upright (5). Tie the

lower end of the wire tie to the Wire Harness

(60). Next, pull the upper end of the wire tie

until the Wire Harness is routed through the

Upright. Then, untie and discard the wire tie.

Tip: To prevent the Wire Harness (60) from

falling into the Upright (5), secure the Wire

Harness with a rubber band or tape.

Tip: Avoid pinching the Wire Harness (60).

nsert the Upright (5) into the Main Frame (1).

Attach the Upright (5) with four M8 x 16mm

Patch Screws (102) and four M8 Split Washers

(103); do not tighten the Patch Screws yet.

3Wire Tie

Wire Tie

Grease

103

102

118

102

118

Avoid pinching

the Wire

Harness (60)

6. See drawing 6a. Locate the Pedal Arm Roller

(32) on the Right Pedal Arm (12).

Lift the Right Ramp Cover (27) and set the

Pedal Arm Roller (32) on the Right Ramp (131).

Then, press the Right Ramp Cover into place.

Repeat this step on the other side of the

elliptical.

See drawing 6b. Apply grease to the axle on

the right Crank Arm (39).

Orient a Pedal Arm Sleeve (46) so that the flat

side is facing the elliptical. Slide the Pedal Arm

Sleeve onto the axle on the right Crank Arm

(39).

Attach the Pedal Arm Sleeve (46) with an M8 x

25mm Patch Screw (121), a Large Axle Cover

(113), and an M8 Washer (95). Tip: Avoid

damaging the Large Axle Cover when tight-

ening the Patch Screw.

Next, pull upward on the Latch (50) on the Right

Pedal Arm (12). Press the Right Pedal Arm onto

the Pedal Arm Sleeve (46). Make sure that the

Right Pedal Arm latches into place.

Repeat this step on the other side of the

elliptical.

5. dentify the Right Pedal (14) and the Right

Pedal Arm (12), which are marked with “Right”

stickers, and orient them as shown.

Attach the Right Pedal (14) to the Right Pedal

Arm (12) with two M6 x 12mm Patch Screws

(111) and two M6 Washers (112); do not

tighten the Patch Screws yet.

Next, tighten two M6 x 50mm Patch Screws

(62) and two M6 Washers (112) into the Right

Pedal Arm (12) and the Right Pedal (14). Then,

tighten the two M6 x 12mm Patch Screws

(111).

Attach the Left Pedal (not shown) to the Left

Pedal Arm (not shown) in the same way.

111

112

113

Flat

Side

112

131

Grease

121

7. dentify the Right Link Arm (43), which is

marked with an “R” sticker. Orient the Right Link

Arm as shown.

Apply grease to the axle on the Right Pedal

Arm (12). Slide the Right Link Arm (43) onto the

axle.

Attach the Right Link Arm (43) with an M8 x

16mm Patch Screw (102), a Small Axle Cover

(56), and an M8 Washer (95).

Next, apply grease to a Link Arm Axle (114).

nsert the Link Arm Axle into the Right Upper

Body Leg (6) and the Right Link Arm (43) from

the side shown.

nsert a hex key into the M8 x 16mm Patch

Screw (102) in the Link Arm Axle (114). Using a

second hex key, tighten another M8 x 16mm

Patch Screw (102), a Small Axle Cover (56),

and an M8 Washer (95) into the other end of

the Link Arm Axle. Tip: Avoid damaging the

Small Axle Cover when tightening the Patch

Screw.

Repeat this step on the other side of the

elliptical.

114

102

Narrow

Tube

Wide

Tube

102

8. dentify the Right Upper Body Arm (8), which is

marked with a “Right” sticker, and orient it as

shown.

Have a second person hold the Right Upper

Body Arm (8) near the Right Upper Body Leg

(6).

Attach the Right Upper Body Arm (8) to the

Right Upper Body Leg (6) with three M8 x

16mm Patch Screws (102).

Attach the Left Upper Body Arm (9) to the

Left Upper Body Leg (7) in the same way.

102

Grease

9. Have a second person hold the Console (33)

near the Upright (5).

Connect the wires on the Console (33) to the

Wire Harness (60) and to the Pulse Wire (105).

nsert the Pulse Wire (105) upward into the

Console (33). nsert the Wire Harness (60)

downward into the Upright (5).

Tip: Avoid pinching the wires. Attach the

Console (33) to the Upright (5) with four M4 x

16mm Screws (106).

See step 3. Tighten the four M8 x 16mm Patch

Screws (102).

105

106

Avoid pinching

the wires

10. Attach the Rear Upright Cover (25) to the

Upright (5) with four M4 x 16mm Screws (106).

106

This manual suits for next models

Table of contents

Other NordicTrack Elliptical Trainer manuals

NordicTrack

NordicTrack NTEL07915.2 User manual

NordicTrack

NordicTrack CXT 990 Quick start guide

NordicTrack

NordicTrack 14.0 Elliptical User manual

NordicTrack

NordicTrack Elite 11.0 NTEVEL99915.1 User manual

NordicTrack

NordicTrack Commercial 14.9 User manual

NordicTrack

NordicTrack NTEL59012 User manual

NordicTrack

NordicTrack Freestride Trainer F55i User manual

NordicTrack

NordicTrack E 12.0 Elliptical User manual

NordicTrack

NordicTrack FREESTRIDER 35 S User manual

NordicTrack

NordicTrack NTEL01712.2 User manual

NordicTrack

NordicTrack E5 si 831.23855.0 User manual

NordicTrack

NordicTrack E 12.2 Elliptical Configuration guide

NordicTrack

NordicTrack Elliptical E7.5 User manual

NordicTrack

NordicTrack Elliptical E7.1 User manual

NordicTrack

NordicTrack 831.23949.2 User manual

NordicTrack

NordicTrack E 8.5 Elliptical User manual

NordicTrack

NordicTrack Commercial PRO NTEL91211.1 User manual

NordicTrack

NordicTrack E 9.9 Elliptical User manual

NordicTrack

NordicTrack E9.2 NTEVEL99812.0 User manual

NordicTrack

NordicTrack E11.0 Elliptical User manual

NordicTrack

NordicTrack CXT 970 User manual

NordicTrack

NordicTrack E4.0 Elliptical User manual

NordicTrack

NordicTrack E9.5 23949.0 User manual

NordicTrack

NordicTrack E7 Rear Drive Elliptical User manual

Popular Elliptical Trainer manuals by other brands

Weslo

Weslo Momentum 4.0 Elliptical Manuale d'istruzioni

Progear Fitness

Progear Fitness Air elliptical pro 1307 owner's manual

Torque Fitness

Torque Fitness XPLLP owner's manual

Octane Fitness

Octane Fitness PRO3700C Operation manual

Xterra

Xterra FS5.8e owner's manual

Bodyguard

Bodyguard E-40 user manual

Bonn Germany

Bonn Germany Concept 2.2 user manual

Precor

Precor Resolute RSL 620 Assembly guide

Vision Fitness

Vision Fitness X6600iNetTV Assembly guide

Matrix

Matrix MX-A5x owner's manual

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 owner's manual

Sears

Sears FREE SPIRIT C249 30737 0 owner's manual

True

True FS-64 Assembly manual

Sport-thieme

Sport-thieme ST 310 manual

VIRTUFIT

VIRTUFIT CTR 1.1 user manual

Kettler

Kettler GIRO C 1 manual

CIRCLE FITNESS

CIRCLE FITNESS E7 owner's manual

Reebok

Reebok 1000 Zx Elliptical Manuel de l'utilisateur