Nikon 1 AW1 User manual

Other manuals for 1 AW1

2

Table of contents

Popular Digital Camera manuals by other brands

Mercury

Mercury 350K user manual

Pentax

Pentax Optio LS 465 operating manual

Sanyo

Sanyo VPC-S1085 instruction manual

GE

GE SMART A1255 user manual

Point Grey

Point Grey Gazelle Getting started

Pentax

Pentax P-5 manual

BlazeVideo

BlazeVideo A280 instruction manual

Sony

Sony MCA-20 manual

Sony

Sony Alpha DSLR-A290 instruction manual

ATIK Cameras

ATIK Cameras One user manual

CohuHD Costar

CohuHD Costar 3930 Series Installation and operation manual

Leica

Leica M10-R quick start guide

FujiFilm

FujiFilm FinePix A700 owner's manual

Lorex

Lorex LNZ81P25 Series quick start guide

GE

GE J1470S user manual

Sony

Sony A6700 Startup guide

Canon

Canon EOS ELAN7 instructions

Samsung

Samsung SCC-C4253 user manual

INTERMEDIATE

Caring for your Nikon 1 AW1

Waterproof Camera

Before Use

Before using the Nikon 1 AW1 waterproof camera under water, it is important that

you attach a 1 NIKKOR waterproof lens onto the camera. [At the time of writing this

article, there are two waterproof 1 NIKKOR lenses, a 10mm and an 11.5-27.5mm

lens.]

If you’ve been using the AW1 with a non-waterproof lens, or if you had the body

cap on the camera, you’ll just need to inspect the O-ring before attaching the

waterproof lens. Make sure there is no dirt or foreign matter on the O-ring; check

that it is correctly positioned and it is not nicked or cracked. Also check the O-ring

seal area of the lens to make sure there is no dust, dirt or foreign matter adhered to

it. If so, clean it off.

Aligning the mounting mark on the body with the lens, carefully place the lens over

the O-ring and press it into position, and then rotate the lens until it stops.

For use underwater, it is recommended that you remove the camera strap that

came with the AW1 and instead use a third-party floating strap. Make sure that the

battery is fully charged and inserted into the camera, and that a blank media card

has also been placed in the card slot. Be careful as you’re closing the battery

chamber door and the media card slot door to make sure that no foreign matter is

adhering to the watertight channels. Clean any dirt with a blower or cotton swab.

Make sure the latches and security locks are fully closed.

FEBRUARY 14, 2020

Before using the waterproof Nikon 1 AW1 and its attached waterproof lens, do a quick

waterproof integrity test by placing the camera in a basin of water and looking for any escaping

air bubbles. After the camera is removed from the water, dry it off and check for leaks.

As a final check, immerse the camera with its waterproof lens attached in a sink or

basin of water to make sure that you don’t see leaks. Turn the camera on and test

the zoom ring and camera controls. Air may escape from the pressure-

equalization vent and microphone and speaker covers, and that’s normal.

If however, you see air escaping from the lens mount or the connector and battery-

chamber/media card slot covers, immediately remove the camera from the water

and dry it thoroughly. Check to see that the O-ring and connector and battery

chamber/media card slot covers are properly sealed. If you find the camera to be

leaking during normal use, consult a Nikon-authorized service center.

If the camera passes the water submersion test, you’re ready to take it shooting

under the sea or in a pool.

After Use

After using the Nikon 1 AW1 underwater, thoroughly rinse the camera in clean water, pressing

the various buttons and extending the built-in pop-up flash to ensure that any salt or foreign

matter is removed from all parts of the camera.

Nikon recommends cleaning the AW1 within 60 minutes of underwater use.

Immerse the camera in fresh water, with its waterproof 1 NIKKOR lens attached to

remove salt or other foreign matter. Leave the camera/lens submerged in a basin

for about 10 minutes. Press the flash pop-up button, rotate the zoom ring if you’ve

got that lens attached and operate the camera’s controls while in fresh water.

After rinsing the Nikon 1 AW1 camera, pat it dry and then let it fully air dry in a cool, shady spot.

Wipe the camera dry. Using a soft, dry cloth, dry the camera and lens barrel.

Let the camera fully air dry before you detach the lens or open the battery door or media card

door.

Let the camera with lens still attached fully dry in a shady spot.

Carefully open the connector and battery compartment/media card slot door and use a soft cloth

to fully dry any water that may have made its way inside.

After confirming that no more water remains on the exterior of the Nikon 1 AW1

and its attached waterproof lens, slowly open the connector and battery

chamber/media card slot covers and remove any water, sand or other foreign

matter using a soft, dry cloth.

After cleaning the camera once it has been used underwater, make sure it is fully dry. Then

remove the lens.

After you’ve confirmed that the lens and camera are dry, detach the lens and

gently wipe the lens O-ring seal with a soft, dry cloth to remove any foreign matter.

There may still be water between the camera and lens, so keep the camera flat

and remove the lens slowly and carefully.

After you carefully detach the waterproof lens from the Nikon 1 AW1, use a soft cloth to fully dry

the rear of the lens where it attaches to the camera.

Using the soft, dry cloth, carefully clean the lens.

Maintenance

Proper care and maintenance of the Nikon 1 AW1’s O-ring is important to keep the

waterproof integrity of the camera and attached waterproof 1 NIKKOR lens.

Carefully remove the O-ring to check it for wear or nicks. You can use either your fingers or an

optional O-ring remover.

When performing routine checks and lubrication of the O-ring, you can remove it

from the camera body either using your fingers or an optional O-ring remover.

While holding the camera securely, lightly stretch the O-ring by sliding your fingers

along either side and remove it from the camera.

Check the integrity of the O-ring, looking for nicks or other signs of wear. The O-ring is what

keeps the waterproof integrity of the camera, so it is important that it is cared for correctly.

Check the O-ring for nicks or cracks, and thoroughly wash it in fresh water, drying

it thoroughly.

Do not use benzene, thinner, alcohol, soap, neutral detergents, or other cleaning

products, as these could damage or weaken the O-ring!

Using a bulb blower, carefully remove dust or foreign matter that may be adhering to the O-ring

or the O-ring guide channel.

Check the O-ring guide for foreign matter and use a blower or cotton swab to clean

off any dirt. Be sure to remove any threads left behind from the cotton swab.

To grease the O-ring, use only the silicon grease that is designed for use with the camera. Place

a small amount of grease in a baggie.

To grease the O-ring, use the silicon grease that came with the Nikon 1 AW1 or

with the optional WP-G1000 silicon grease. Place a bead of the silicon grease in a

plastic bag and use your fingers to spread the grease around inside the bag.

Do not use the lubricant that is used for COOLPIX or NIKONOS underwater

camera’s O-rings!

Once the silicon grease has been inserted into the baggie, place the O-ring inside and using

your fingers, thoroughly cover the O-ring.

Then insert the O-ring in the bag and massage the bag to fully coat the O-ring.

This prevents wear on the O-ring and makes it easier to attach and remove the

waterproof lenses from the Nikon 1 AW1.

Carefully replace the O-ring, making sure that it sits correctly in the channel, and is not stretched

or bulging.

After making sure that the O-ring and the guide are free of foreign matter, place the

O-ring so that it runs evenly at the same level, all the way around the O-ring guide.

The O-ring should not be overly stretched, nor should it protrude from the camera

body.

Using the AW1 with a non-waterproof 1

NIKKOR lens

The Nikon 1 AW1 is a waterproof camera, when used with its waterproof lenses.

You can also use the Nikon 1 AW1 with non-waterproof 1 NIKKOR lenses with the

caveat that the camera will not be waterproof with a regular lens attached.

To use the Nikon 1 AW1 with a regular, non-waterproof 1 NIKKOR lens, you will

have to protect the O-ring on the camera with the supplied O-ring protector.

When you are using the Nikon 1 AW1 with a waterproof lens, place the O-ring protector on the

body cap that came with the camera for safe keeping. This way, you always know where it is

when you need it.

The O-ring protector is supplied with the camera and should be kept on the body

cap of the AW1 when it is not being used.

Because the O-ring ensures the waterproof integrity of the Nikon 1 AW1 and its waterproof lens,

it is important to protect the O-ring when you are not using the camera with a waterproof lens.

Place the O-ring protector over the O-ring before attaching a non-waterproof 1 NIKKOR lens on

the camera.

To place it on the camera, simply remove the O-ring protector from the body cap,

and place it over the O-ring, on the AW1 camera body.

With the O-ring protector covering the O-ring, you can now attach a non-waterproof 1 NIKKOR

lens to the Nikon 1 AW1 camera.

With the O-ring protector in place, the O-ring is protected from dirt and damage,

and you are now able to place a non-waterproof 1 NIKKOR lens on the camera.

To do so, just make sure you’ve got the mounting mark on the lens and on the

camera body lined up, and position the lens on the camera. Then rotate the lens