Nietzsche Enterprise WZB-SMB02 User manual
WZB-SGB02, ZigBee Magnec Switch, is
a wireless device with pulse detecng funcon
which is used to secure glass from being broken
and operang with WZB-06GP ZigBee
Mul-Gateway to protect any unexpected
break through. They add an extra layer of
security to homes and small businesses, and
add peace of mind for families with young
children.
Periodic transmission of supervision
signals is used to confirm system connecvity
at all mes. The detector is powered by a
standard CR2032 baery, which is constantly
monitored, with automac reporng to the
Mul-Gateway when the baery needs to be
replaced.
By binding it to the central device of
security system, WZB-06GP ZigBee
Mul-Gateway, the ZigBee Glass Break
Detector is default as Zone #7, whenever the
magnec switch triggers, then the WZB-06GP
will send out SOS messages to assigned 4 SOS
cellphone numbers and push Digital output #7
correspondingly. Maximum distance for
wireless connecon is 150 meters (in open
areas). Although line of site is not required, the
maximum range is based on opmal condions
with minimal interference. Objects such as
walls, trees, etc affect wireless range. Actual
range may vary, depending on environment.
PRODUCT INTRODUCTION
1. Wireless Magnec door contact
2. Transming Distance: 150m (490 feet)
(Line of sight)
3. Transming Distance: 150m
4. Transming Current: 30mA
5. Sending Frequency: 2.4GHz
6. Trigger resistance: ∞Ω
7. Surge proof voltage: 2000V(Max)
8. Acvated holding me: 3~10 seconds
9. Ambient temperature: -10℃~60℃
(14℉~140℉)
10. Dimension: ψ3.7 * 1.6 cm
(ψ1.4 * 0.6 inches)
11. Baery Life: 1 to 2 year
12. Baery type: CR2032 3.0V Lithium
Ion Baery
13. Number of baeries: 1
PRODUCT PROFILE
• Superior transmission range.
• Fully supervised.
• Factory-selected ID
• Long-life standard lithium baery included.
• Low-baery signaling.
• Compable with WZB-06GP and
WZB-02485R, wireless panels and repeaters.
1. Wireless glass break detecng
2. Transming Distance: 150m (490 feet)
(Line of sight)
3. Baery Life: 1 to 2 year
SPECIFICATION
PRODUCT FEATURE
DETAILED PRODUCT DESCRIPTION
1. Taking the baery into baery box before
installaon. And make sure WZB-06GP is
powered on.
2. Press WZB-06GP S1 to JOIN the glass break
detector. Once the glass break detector
has been linked, the blue LED light on front
cover will flash every 30 seconds. If
WZB-06GP does not link with Magnec
Switch, then just press WZB-06GP S1 once
again unl the Magnec Switch is being
linked.
Please note: Do NOT power on the devices that
you do not want to link.
Please avoid pressing 2 WZB-06GPs’ S1 buons at the same me.
3. Check the glass break detector to see if it comes into operang state. Once the Magnec
Switch has been linked, the blue LED light on front cover will flash every 30 seconds.
4. Aer linking, you may hit the glass break detector to test the output of the glass break
detector. The glass break detector should send out RF signal to WZB-06GP and trigger the
digital output #7. (Installaon is completed)
5. Select proper place (normally mounted on the side of windows glass), fix it with scky strips
or glues.
6. If you want to disconnect one glass break detector, you can press WZB-06GP S1 for 2 mes
quickly, then follows pressing the intended disconnecng glass break detector S1 for 3 mes
quickly, then it will disconnect the single glass break detector from the Wireless Network.
7. If you want to dismiss all Wireless Network, then press WZB-06GP S1 for 1 me long press
unl it pops up both red and blue light; then press all other glass break detector for 1 me
long press unl it pops up long blue light. Now the whole network is dismissed. Then the
detectors are ready to join other wireless network.
NOTICE
1. The glass break detector should have two quick LED flash regularly when it is in low
baery. When low baery happens, please change the baery immediately.
2. The glass break detector cannot be installed under worse environment. E.g. coldest,
hoest, dusty.
3. Please test it monthly.
4. For various reasons, including, but not limited to changes in environmental condions,
electric disrupons and tampering, the product may not perform as expected. The user is
advised to take all necessary precauons for his/her safety and the protecon of his/her
property.
5. Please install detectors away from other 2.4GHz devices at least 2 meters to avoid from
possible interference.
INSTALLATION AND TEST
INSTALLATION AND TEST
Table of contents
