Nice MC200 Technical specifications

EN - Instructions and warnings for installation and use

IT - Istruzioni ed avvertenze per l’installazione e l’uso

FR - Instructions et avertissements pour l’installation et l’utilisation

ES - Instrucciones y advertencias para la instalación y el uso

DE - Installierungs-und Gebrauchsanleitungen und Hinweise

PL -

NL - Aanwijzingen en aanbevelingen voor installatie en gebruik

RU - Инструкции ипредупреждения по монтажу иэксплуатации

Control unit

Nice

MC200

1 – English

The following warnings are taken directly from the Regulations and apply, as far as possible, to the product described herein

WARNING Important safety instructions. Observe all the instructions as improper installation may cause serious damage

WARNING Important safety instructions. It is important to comply with these instructions to ensure personal safety. Store these

instructions

•

your guided part. Should it be unsuitable, DO NOT proceed with the installation

•

WARNING According to the most recent European legislation, the implementation of an automation system must comply with

the harmonised standards set forth in the Machinery Directive in force, which allow for declaring the presumed

conformity of the automation. On account of this, all operations regarding connection to the mains electricity, as



technician!

•Before proceeding with the product’s installation, check that all materials are in good working order and are suitable for the intended

applications

•The product is not intended for use by persons (including children) with reduced physical, sensory or mental capacities, nor by anyone lack-



•Children must not play with the appliance

•Do not allow children to play with the control devices of the product. Keep the remote controls out of reach of children

WARNING In order to avoid any danger from inadvertent resetting of the thermal cut-off device, this appliance must not be powered through



GENERAL WARNINGS: SAFETY - INSTALLATION - USE

(instructions translated from Italian)

ENGLISH

English – 2

•Provide a disconnection device (not supplied) in the plant’s mains power supply, with a contact opening distance that ensures complete

disconnection under the conditions envisaged by Overvoltage Category III

•Handle the product with care during installation, taking care to avoid crushing, knocks, falls or contact with liquids of any kind. Keep the



or malfunctions. If this should happen, stop installation immediately and contact the Customer Service

•The manufacturer assumes no liability for damage to property, items or persons resulting from non-compliance with the assembly instructions.

In such cases the warranty does not cover material defects

•Cleaning and maintenance to be carried out by the user must not be effected by unsupervised children

•Before intervening on the system (maintenance, cleaning), always disconnect the product from the mains power supply

•The packaging materials of the product must be disposed of in compliance with local regulations

•When performing a manoeuvre, keep an eye on the automated mechanism and keep all bystanders at a safe distance until the movement

has been completed

•Do not operate the automation if any people in the vicinity are working on it; disconnect the power supply before permitting any work to be

carried out

PRODUCT DESCRIPTION AND INTENDED USE

MC200 is an electronic control unit that allows for controlling and commanding a motor designed to automate a shutter, overhead door, sectional

door, rolling shutter or other similar applications.



to be considered improper and is forbidden!





• it can be programmed by setting 8 dip-switches;

• it is equipped with an incorporated radio receiver that allows for controlling the automation through a radio transmitter;

-



edge, etc.





3 – English

USE LIMITATIONS

a) powered from the mains

and sized for the same voltage that powers the control unit; b) equipped with a thermal cut-off; c) equipped with a mechanical device that limits

its movement (limit switch); d)

• The radio receiver incorporated in the control unit is only compatible with transmitters that adopt the FLOR, O-CODE or SMILO radio coding

protocols (these are Nice standards).



INSTALLATION

Important! - Prior to installing the product, check its use limitations by reading Chapters 2 and 7.

Check that the temperature is suitable for the type of application.

The product must not be installed outdoors.

When drilling the control unit box for passing the cables (Fig. 1-C), it is important to remember that the cables must always

enter the box from below. Moreover, take suitable precautions to guarantee the required protection rating (IP 44) for the type of

installation.

Before proceeding with the installation, prepare the electrical cables required for the system by referring to Fig. 2b and to “Table



Warning! – When laying the tubes for protecting the electrical cables and when laying the cables into the control unit housing,

bear in mind that due to possible water deposits in the junction wells, the cable protection tubes might create water vapour the

control unit, with consequent damage to the electronic circuits.

Install the control unit by referring to Fig. 1.

English – 4

45 mm128 mm

112 mm

Ø 3,5 x 35

x 2

Electrical

connections.

Refer to Chapter 4

A B C

D E F G

If necessary,

use the cable

entry openings

at the rear of the

but only

with suitable

.

Drill the

underside

of the

control

unit box.

5 – English

ELECTRICAL CONNECTIONS

WARNING! – All electrical connections must be made with the system disconnected from the power supply. Incorrect connec-

tions can damage the equipment or injure people.



4.1 - Arranging the electrical cables to connect devices to the control unit (Table A)

Table A - Characteristics of electrical cables for the relevant connections

Device to be connected Cable cross-section Maximum cable length



UNIT 230 m (*1)

WARNING LIGHT WITH RADIO AN-

TENNA

2 (for the lamp)

 20 m



DEVICES CONNECTED TO TERMINALS

8-9-10-11-12-13 2 (*2) 

 210 m

(*1) 2.

(*2)2 cable.

WARNING! – The cables used must be suited to the type of environment of the installation site.

4.2 - List of control unit parts

During the successive control unit connection and programming phas-

  Fig. 2

and its key.

A - Line fuse (6.3 A)

B - Connector for inserting the IBT4N interface

C  

D  

E - T2 button, for memorising a transmitter and for cancelling a trans-

mitter or the entire control unit memory

F - T1 button, for programming and for sending step-by-step com-

mands

G - Dip-switch for programming the functions

English – 6

H  

I - Terminals for radio antenna

L - Low-voltage input terminals

M - Terminals for connecting the power supply line and for the motor

12345678

CLN

Com

24V

Photo

Test

Photo

SbS

Stop

7 – English

4.3 - Basic connections

• Connecting the motor to the MC200 control unit

Connect the 3 conductors coming from the motor (Up phase, Common, Down phase) respectively to terminals 3, 4 and 5 of the control unit,

as shown in Fig. 3.

WARNING! Before connecting the motor, it is imperative to verify that the conductor connected to terminal 3 causes the door to

OPEN, that the conductor connected to terminal 5 causes the door to CLOSE, and that the conductor connected to terminal 4

is the COMMON conductor.

Warning! – 



• Connecting the power supply to the MC200 control unit

Connect the 2 wires coming from the mains (Live and Neutral) respectively to terminals 6 and 7 of the control unit, as shown in Fig. 3.

• Earthing the motor

Warning! - To comply with the electrical safety requirements of the relevant product class (Class II), it is mandatory to earth the motor outside

of the MC200 control unit.

“S”

8,2kΩ

Sensitive edge

English – 8

4.4 - Connection of accessories

To connect the relevant accessories refer to Table B, to Fig. 3 and to the instruction manual of each accessory. Table B summarises all the ac-

Before proceeding,

carefully read the table and its notes. Note – Due to the fact that certain inputs offer different functions for connecting the accessories, once the



Table B

Terminals Description of the function

1 - 2 Output

3 - 4 - 5 Output for controlling the motor (open, common, close).

6 - 7 Input of the power supply line coming from the mains (live, neutral).

8 Reference to 0 V for the “9, 10, 11, 12 and 13.

9 24 V output. 

10 Photo test output. 24 V output

11 Stop input. Input 

12 SbS input. Input for a normally open (NO) button, for sending commands in step-by-step mode.

13 Photo input. Input for a normally closed (NC) reception photocell (RX), or for a normally open (NO) button.

14 - 15 Input for an antenna-radio receiver.



4.5.1 - Photo test output (terminal 10)

7



NOTES9. • The “door open indica-



light off = door closed; light on = door open;  = door in opening phase;  = door in closing phase.

4.5.2 - Stop input (terminal 11)

1 - 2 depending  normally closed (NC) con-

 Warning!

1 - 2 guarantees the minimum level of resistance against faults, requested by the regulations. Normally the

9 – English

intervention of the device connected to the Stop input causes the immediate stoppage of the motor’s movement, with a brief inversion of the

manoeuvre (selectable through dip-switch 3



to the sensitive edge (see Fig. 4). The  contact must be placed so that it closes in the last 30/40 mm of the closing manoeuvre, before the

sensitive edge intervenes. In this way, when the -

tion stops without inverting the manoeuvre and the door remains fully closed. In this condition, the system allows for commanding the opening

manoeuvre only.

The status of the Stop inputTable C.

Table C

 Meaning (status of the Stop input)

On Active (consent for manoeuvre)

Off Not active (manoeuvre stopped)

50% on + 50% off Inversion deactivated

20% on + 80% off Not active, with inversion deactivated (allowed only after the opening manoeuvre)

4.5.3 - SbS input (terminal 12)

Whenever the button connected to this input is pressed, the system runs the command following the last command sent, according to a default



pressed (from 4 to 10 seconds), the system always commands an opening manoeuvre; if instead the button is held for more than 10 seconds, the

system always commands a closing manoeuvre. This particular function can be useful whenever there are multiple control units, when the user

wishes to control them simultaneously and have the doors perform the same manoeuvre, regardless of the current status of each control unit.

4.5.4 - Photo input (terminal 13)

4-



be set to ON. Note – If a normally closed (NC) reception photocell (RX) has been connected, if there is no consent only the opening manoeuvre

can be carried out.

Other manuals for MC200

Table of contents

Other Nice Control Unit manuals

Nice

Nice TTPRO Technical specifications

Nice

Nice UST1-FU Quick start guide

Nice

Nice POA1/A Technical specifications

Nice

Nice mindy TT1N Product manual

Nice

Nice UDL 2 Quick start guide

Nice

Nice TT4 Product manual

Nice

Nice HSTS2 Technical specifications

Nice

Nice MC424L Technical specifications

Nice

Nice Mindy A824 Product manual

Nice

Nice FGR-223 User manual

Nice

Nice TT6 Technical specifications

Nice

Nice ROBO PLUS Service manual

Nice

Nice MOONCLEVER MC424 Technical specifications

Nice

Nice Moon MC824H Technical specifications

Nice

Nice RC2 Technical specifications

Nice

Nice TT1VR Technical specifications

Nice

Nice MC800 Technical specifications

Nice

Nice mindy A60 User manual

Nice

Nice CLB207 Technical specifications

Nice

Nice MINDY A02 Product manual

Nice

Nice mindy A60 Product manual

Nice

Nice TCE Product manual

Nice

Nice Oview User manual

Nice

Nice RO 1000 Product manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual