Nibe F110 User manual

Installation manual

Hot water heat pump

NIBE F110

LEK

IHB EN 2344-1

731934

Quick guide

Navigation Ok button (confirm/select)

Back button (back/undo/exit)

Up/down buttons

(move/increase/reduce)

A detailed explanation of the button functions can be found on page 23.

How to scroll through menus and make different settings is described on page 24.

Increase hot water volume

true

off

To temporarily increase the amount of hot water, first press the down button to mark menu 2 (water droplet) and then

press the OK button twice. Read more about the settings on page 26.

In event of disturbances in comfort

If a disturbance in comfort of any type occurs there are some measures that can be taken before you need to contact

your installer. See page 33 for instructions.

41 Important information

4Safety information

4Symbols

4Marking

5Serial number

5Recovery

6Inspection of the installation

72 Delivery and handling

7Transport

7Assembly

8Supplied components

8Handling panels

113 The Heat pump design

12List of components

134 Pipe and air connections

13General pipe connections

14Dimensions and pipe connections

15Cold and hot water

16Installation alternative

18General ventilation connections

19Ventilation flows (exhaust air)

19Adjusting ventilation (exhaust air)

19Dimensions and ventilation connections

205 Electrical connections

20General

20Connections

20Optional connections

216 Commissioning and adjusting

21Preparations

21Filling and venting

21Start-up and inspection

237 Control - Introduction

23Display unit

23Menu system

258 Control - Menus

25Menu 1 - ventilation

26Menu 2 - HOT WATER

28Menu 3 - INFO

29Menu 4 - MY SYSTEM

30Menu 5 - SERVICE

329 Service

32Service actions

3310 Disturbances in comfort

33Info menu

33Manage alarm

33Troubleshooting

3511 Accessories

35Separable valve connector

35Base extension EF 45

35Top cabinet TOC 40

3612 Technical data

36Dimensions

37Technical specifications

38Energy labelling

39Electrical circuit diagram

40Item register

43Contact information

3Table of ContentsNIBE F110

Table of Contents

Safety information

This manual describes installation and service procedures

for implementation by specialists.

The manual must be left with the customer.

For the latest version of the product’s documentation, see

nibe.eu.

This appliance can be used by children

aged from 8 years and above and per-

sons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning use

of the appliance in a safe way and under-

stand the hazards involved. Children shall

not play with the appliance. Cleaning and

user maintenance shall not be made by

children without supervision.

This is an original manual. It may not be

translated without the approval of NIBE.

Rights to make any design or technical

modifications are reserved.

©NIBE 2023.

Do not start F110 if there is a risk that the

water in the system has frozen.

Water may drip from the safety valve’s

overflow pipe. The overflow pipe must be

routed to a suitable drain, to prevent hot

water splashes from causing harm. The

overflow pipe must be inclined along its

entire length to prevent pockets where

water can accumulate, and must be frost-

proof. The overflow pipe must be at least

the same size as the safety valve. The

overflow pipe must be visible and its mouth

must be open and not placed close to elec-

trical components.

The safety valve must be actuated regularly

to remove dirt and to check that it is not

blocked.

Electrical installation and wiring must be

carried out in accordance with national

provisions.

If the supply cable is damaged, only NIBE,

its service representative or similar author-

ised person may replace it to prevent any

danger and damage.

Symbols

Explanation of symbols that may be present in this manual.

NOTE

This symbol indicates danger to person or machine.

Caution

This symbol indicates important information about

what you should consider when installing or servi-

cing the installation.

TIP

This symbol indicates tips on how to facilitate us-

ing the product.

Marking

Explanation of symbols that may be present on the product’s

label(s).

Read the User Manual.

Read the Installer Manual.

NIBE F110Chapter 1 | Important information4

Important information

Serial number

The serial number can be found at the bottom right of the

front cover.

Serial number

Caution

You need the product's (14 digit) serial number for

servicing and support.

Recovery

Leave the disposal of the packaging to the installer

who installed the product or to special waste sta-

tions.

Do not dispose of used products with normal

household waste. It must be disposed of at a special waste

station or dealer who provides this type of service.

Improper disposal of the product by the user results in ad-

ministrative penalties in accordance with current legislation.

5Chapter 1 | Important informationNIBE F110

Inspection of the installation

Current regulations require the heating installation to be inspected before it is commissioned. The inspection must be

carried out by a suitably qualified person.

DateSignatureNotesDescription

✔

Ventilation, exhaust air (page 16)

Setting the ventilation flow

Exhaust air filter

Ventilation, surrounding air or outdoor air (page 17)

Pressure drop in the system

Hot water

System vented

Electricity (page 20)

Supply connected 230 V

Circuit fuses

Earth circuit-breaker

Miscellaneous

Type of installation

NIBE F110Chapter 1 | Important information6

Transport

F110 should be transported and stored vertically in a dry

place.

However, the F110 can be carefully laid on its back when

being moved into the building. The centre of gravity is in the

top section.

Assembly

•Position F110 on a solid foundation indoors that withstands

water and the weight of the product.

•Use the product’s adjustable feet to attain a horizontal

and stable set-up.

30 - 50 mm

15 - 40 mm

20-55 mm

•Since water comes from F110, the area where F110 is loc-

ated must be equipped with floor drainage.

•Because water comes from F110, the floor coating is im-

portant. A waterproof floor or floor membrane is recom-

mended.

•Install with its back to an outside wall, ideally in a room

where noise does not matter, in order to eliminate noise

problems. If this is not possible, avoid placing it against a

wall behind a bedroom or other room where noise may be

a problem.

•Wherever the unit is located, walls to sound sensitive

rooms should be fitted with sound insulation.

•Route pipes so they are not fixed to an internal wall that

backs on to a bedroom or living room.

•The installation area always has to have a temperature of

at least 10 °C and max. 30 °C.

INSTALLATION AREA

Leave a free space of 800 mm in front of the product. Leave

free space between F110 and wall/other machinery/fit-

tings/cables/pipes etc. It is recommended that a space of

at least 10 mm is left to reduce the risk of noise and of any

vibrations being propagated.

800

NOTE

Ensure that there is sufficient space (300 mm)

above F110 for connecting ventilation ducts.

7Chapter 2 | Delivery and handlingNIBE F110

Delivery and handling

Supplied components

LEK

Filter cartridgeSilencer

Air connection

LOCATION

The kit of supplied items is placed in the lower section of

the product.

Handling panels

REMOVE THE AIR TREATMENT UNIT’S HATCH

1. Loosen the screws for the securing plates above F110.

2. Slide the hatch upwards.

3. Pull the hatch towards yourself.

LEK

NOTE

An earth cable is installed in the hatch, which can

therefore only be lifted out 35 cm. If the hatch

needs to be removed completely, the cable must

be disconnected.

REMOVE THE FRONT

1. Pull the panel towards yourself.

NOTE

A display cable is installed in the panel, it can

therefore only be lifted out 1.5 m. If the panel

needs to be removed completely, the cable

must be detached.

LEK

NIBE F110Chapter 2 | Delivery and handling8

REMOVE SIDE PANELS

Air treatment section

1. Undo the screws at the edge.

LEK

2. Twist the panel slightly outwards.

LEK

3. Move the panel outwards and backwards.

LEK

4. Assembly takes place in the reverse order.

9Chapter 2 | Delivery and handlingNIBE F110

Water heater section

1. Remove the screws from the upper and lower edges.

LEK

2. Twist the panel slightly outwards.

LEK

3. Move the panel outwards and backwards.

LEK

4. Assembly takes place in the reverse order.

NIBE F110Chapter 2 | Delivery and handling10

Other manuals for F110

Table of contents

Popular Heat Pump manuals by other brands

MICROWELL

MICROWELL HP 1000 GREEN Installation and user manual

Sanyo

Sanyo SAP120FCH Service manual

Daikin

Daikin EHYHBH05AA Operation manual

Panasonic

Panasonic WH-SDF03E3E5 Design handbook

Bryant

Bryant 544B Specifications

Airxcel

Airxcel 45000 Series Installation, operation and maintenance instructions

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Service manual

Dimplex

Dimplex LI 16I-TUR Installation and operating instruction

Carrier

Carrier WSHP Open v3 Integration guide

TGM

TGM CTV14CN018A Technical manual

Carrier

Carrier 38MGQ Series installation instructions

Kokido

Kokido K2O K880BX/EU Owner's manual & installation guide

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Installation and service instructions

Carrier

Carrier 48EZN installation instructions

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Installation and service instructions for contractors

Ariston

Ariston NIMBUS user manual

Weishaupt

Weishaupt WWP L 7 Installation and operating instruction

GE Zoneline AZ85H09EAC datasheet