Neunaber IMMERSE User manual

I M M E R S E

r e v e r b e r a t o r

US E R GU I D E

Thank you for purchasing our product. We really mean it. We hope to earn

your trust by delivering a quality product that inspires you to make great

music.

Neunaber products are designed and manufactured in Orange, California

USA. Please visit neunaber.net for more information and support.

Connections

We recommend that this pedal be placed at the end of your chain, after all

other effects. If you are using the overdrive channel of your amplifier, this

effect should be placed in the effects loop for best results.

The POWER JACK accepts a standard (5.5 mm OD x 2.1 mm ID) center-

negative pedal power adapter (not included). The power adapter must be

between 9V and 12V and capable of supplying 70mA or more.

The INPUT JACKS (right side) accept inputs directly from your instrument,

amplifier effects loop output, or other effect pedals via standard 1/4" (6.35

mm) phone connectors.



Input 1 only

accepts a mono input.



Both Inputs 1 & 2

accept a stereo input.



Input 2 only

accepts a stereo TRS input.

The OUTPUT JACKS (left side) supply output to another effect pedal, an

amplifier, or effects loop return via standard 1/4" (6.35 mm) phone

connectors. The buffered output is capable of driving long cables. If plugging

into the input of an amp, you should use the low impedance (Lo-Z) input if

available.



Output 1 only

supplies a summed mono output.



Both Outputs 1 & 2

supply a stereo output. Using both outputs creates a

stereo signal from a mono input.



Output 2 only

supplies a stereo TRS output.

The input and output connections are independent. You may—for example—

use a mono input with stereo outputs or stereo inputs with a stereo TRS

output.

Important Note:

input/output 1 and input/output 2 should not be used with

two discrete signals (such as two different instruments).

The FOOT SWITCH bypasses the effect. The LED lights when the effect is

active. Bypassing the effect does not lower power consumption, because it

does not turn off power to the pedal.

The Immerse Reverberator implements a high-quality buffered bypass. The

signal is always buffered whether on or bypassed. We chose this type of

bypass because the last output in a pedal chain should be buffered, and

reverb is typically placed at the end of a pedal chain.

The KILL DRY switch removes the dry signal, leaving only the "wet" (effect)

signal. This is useful for parallel effect loops.

The TRAILS switch changes the bypass mode between normal and trails.

Trails allows the effect to naturally trail off after the pedal is bypassed. With

normal bypassing, the effect is abruptly cut off; however, normal bypassing

results in lower noise while the pedal is bypassed.

Effects

Reverberation ("reverb") gives your instrument a sense of acoustic

spaciousness. There have been various methods of simulating this effect

over the years, several of which have evolved into their own distinct sound.

WET™is an updated version of Neunaber's renowned algorithm, with shorter

pre-delay, higher initial density and more balanced imaging.

fx level adjusts the reverb level

depth adjusts the length of the reverb tail (size of the acoustic space)

tone controls the tone of the reverb only

modulate controls the speed and depth of modulation in the reverb

HALL reverb is known for its large, open sound—similar to what one may find

in a well-designed concert hall.

fx level adjusts the reverb level

depth adjusts the length of the reverb tail (size of the acoustic space)

tone controls the tone of the reverb only

modulate controls the speed and depth of modulation in the reverb

A physical PLATE reverb uses transducers mounted to a large, suspended

metal plate. It is known for its bright, diffuse sound.

fx level adjusts the reverb level

depth adjusts the length of the reverb tail (size of the acoustic space)

tone controls the tone of the reverb only

pre delay controls the delay time before the reverb

A physical SPRING reverb uses metal springs suspended between

transducers and produces a distinctive initial "twerp."

fx level adjusts the reverb level

depth adjusts the length of the reverb tail (size of the acoustic space)

tone controls the attenuation of high frequencies in the reverb only

low cut controls the attenuation of low frequencies in the reverb only

SHIMMER A&Bare reverb effects reminiscent of a synth pad that follows

what your instrument plays.

fx level adjusts the effect level

depth adjusts the length of the reverb tail (size of the acoustic space)

tone (a) controls the tone of the effect

tone (b) controls the frequency range of the effect

shim level controls the amount of shimmer present in the effect

+ECHO combines the Wet™ Reverb with echo.

fx level adjusts the level of both reverb and echo

depth adjusts the length of the reverb tail and the repeats of the echo

echo time controls the delay time, from 50 to 720 ms.

rvb level controls the mix between echo and reverb—from 100% echo (full

counter-clockwise) to 100% reverb (full clockwise)

+DETUNE combines the Wet™ Reverb with detune, which is a chorusing-like

effect that adds in a slightly detuned double of the dry signal.

fx level adjusts the effect level—for the detune effect to be heard, set at 3

o'clock or higher

depth adjusts the length of the reverb tail

tone controls the tone of both the reverb and detune

rvb level controls the level of reverb

Warning:

This product contains no user-serviceable parts. Opening the pedal may

expose sensitive components to electro-static discharge, resulting in permanent

damage. Please do not remove the bottom cover or otherwise disassemble the pedal.

Wet™ are trademarks of Neunaber Technology, LLC. US Patent #8204240 & China

Patent #CN101689840B.

Specifications

ELECTRICAL

Nominal Input Level

-10 dBV, instrument level

Absolute Max Input Level

6 dBV

Input Impedance

1 MΩ (mono), 2 MΩ (stereo)

Output Impedance

500 Ω (mono), 1 kΩ (stereo)

Gain, enabled vs. bypass

0dB (Mix @ 0)

Frequency Response

20Hz—20kHz, +0.1dB, -0.5dB (dry signal or bypassed)

Total Harmonic Distortion

< 0.003 % typical

(dry signal or bypassed, 22Hz—22kHz, 1.0 VRMS, 1 kHz)

Signal-to-Noise Ratio

112 dB mono, 110 dB stereo (A-weighted)

POWER

Power Adapter Input

9-12 V DC, 70 mA

plug: center-negative, 5.5 mm OD x 2.1 mm ID

PHYSICAL

Dimensions

2.9" W, 4.6" L, 2.0" H / 73 mm W, 117 mm L, 51 mm H

Weight

8.5 oz / 240 g

*Specifications subject to change without notice.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

Other manuals for IMMERSE

Other Neunaber Recording Equipment manuals

Neunaber

Neunaber ECHELON ECHO v2 User manual

Neunaber

Neunaber IMMERSE User manual

Popular Recording Equipment manuals by other brands

KV2 Audio

KV2 Audio 500 Series user guide

Robotics Technologies

Robotics Technologies microBus-Cam II installation manual

Seca

Seca 460 quick start guide

Cognex

Cognex MVS-8000 Series Hardware manual

Mect

Mect MPNC006 Series user manual

Bad Caf

Bad Caf THE LEASH operating manual

Strymon

Strymon NIGHTSKY user manual

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U user manual

Tews Technologies

Tews Technologies TPMC465 user manual

Honeywell

Honeywell Excel 50 user guide

SeaLevel

SeaLevel COMM+8.LPCI user manual

Arturia

Arturia AUDIOFUSE STUDIO user manual

Rukra

Rukra RK-1240 quick start guide

Samson

Samson SCOM owner's manual

Dynacord

Dynacord DPS260 owner's manual

Nice

Nice Core user manual

Pyle Pro

Pyle Pro PSS8 manual

RF-System

RF-System TinyGate Assembly and user's manual