Netum RS-8000 User manual
Package Included:
1 x Scanner; 1 x Dock;
1 x USB cable; 2 x Baeries;
1 x Quick Manual;
Model:RS-8000/RS-9000
Bluetooth Ring Scanner
V20.12.31
1. Product Informaon
(1)
① Scanning Window
② Scanner LED
③ Baery Door
④ Buzzer
⑤ Trigger Buon
⑥ Adjustable Ring Belt
① Baery Charging Dock
② DC Port
③ Type C Port
④ Bluetooth LED
⑤ Transmission LED
⑥ Baery charging LED
⑦Scanner Power charging LED
1
2
3
4
5
6
1
2
3
4
5
6
7
2. Charge The Baery
2.1. Press and push up the
baery door
2.2. Insert baery and secure
baery door
(2)
3.Scanner's Bluetooth Connecon Status
Baery Dock LED Status：
1) Solid Blue- Bluetooth
Connected
2) Flashing Blue- Bluetooth
Disconnected/Bluetooth Pairing
(3)
4
32
1
① Scanner LED
1) Solid Red- Full Charged
2) Flashing Red- Charging
② Baery LED
1) Solid Red- Full Charged
2) Flashing Red - Charging
④ Bluetooth connecon status
1) Solid Blue- Scanner has connected with the dock
2) Flashing Blue- Scanner has disconnected with the dock
③ Transmission LED
1) Solid Green- No Transmit
2) Flashing Green- Transferring data
Bluetooth
LED
4. Setup Guide
(4)
Firmware Version
Read below command barcode to check scanner firmware version.
Barcode Programming
Netum barcode scanners are factory programmed for the most common
terminal and communicaons sengs. If you need to change these
sengs, programming is accomplished by scanning the bar codes in this
guide. An asterisk (*) next to an opon indicates the default seng.
Get Started
1）Pair Netum bluetooth (refer to the secon of “Bluetooth pairing”)
2）Setup keyboard language: US keyboard is set by default. If you use
other type of keyboard please refer to the secon of “keyboard language”.
3）Locate cursor on place where you want the data to be displayed aer
that you can start to scan.
Bluetooth Pairing
How to pair scanner's bluetooth with the dock ?
1) Connect the dock with your computer via USB
cable.
Firmware Version
(5)
Keyboard Language
For example If you use French Keyboard, scan command barcode of
“French keyboard ”. If you use a US keyboard you can ignore this step.
Important Note:
Default Idle Time: Scanner will power off automacally if device is not
connected in 3mins . If you want BLE and SPP mode, please contact us.
2) Scan QR code from the dock, Bluetooth paired once blue LED on the
dock turns to solid blue.
3) If you want to disconnect it with the dock and connect it with your
device, scan "Bluetooth HID" then pair Netum Bluetooth.
Bluetooth HID (Default)
* America EN keyboard French keyboard
Germany keyboard Italy keyboard
(6)
*Quit Offline Mode
Portugal keyboard Spain keyboard
UK keyboard Czech keyboard
Hungary keyboard Belgium FR keyboard
Data Uploading Mode
If you are heading for a working area which lies outside the bluetooth signal
range, you may acvate scanner’s store mode, following steps described be-
low. Under this mode,all scanned data will be stored directly into the buffer
memory of the device. Furthermore, the data entries will be permanently
saved in the buffer memory prior to the manual upload into the working
staon, so that you may upload them when you are near your working device.
By scanning the following barcode, the device leaves the offline mode, normal
mode will be reinialised.
(7)
Output Total Entry
By scanning the following barcode, the gross quanty of the uploaded data
entries will be summarised .
Offline Mode
By scanning the following barcode, the offline mode will be acvated.
Clear Memory
By scanning the following barcode, all data in the buffer memory will be
deleted.
Output Stored Data
By scanning the following barcode, all data entries in the buffer memory
can be manually uploaded aer reconnecng to the working staon.
Output Total Entry
Offline Mode
Clear Memory
Output Stored Data
(8)
Idle me
Scanner will turn to sleep aer idle/inacve for 1min
Scan "Disable module Idle me" before you doing any other setup from this
secon.
Get Baery Volume
Scan below command barcode to get baery rough volume.
1) Voltage < 3.5V, Low baery Volume, there will have 5 beeps aer each
scan. Scanner can not be able to read any barcodes.
2) 3.7V< Voltage < 3.5V, Low baery Volume, there will have 2 beeps aer
each scan. Scanner sll be able to read barcodes.
3) Voltage >4.2V , Full Volume
Power Off Disable Sleep Mode
* 3mins 1Hour
Baery Rough Volume
(9)
IOS Keyboard POP UP/HIDE
During the scanning IOS keyboard can be hided or popped up by scanning
below command barcode.
1)Scan this barcode at Bluetooth HID connected state on IOS device, popup
IOS keyboard.
2) Popup IOS keyboard by hold trigger 4 seconds.
3) Popup IOS keyboard by double click trigger.
Note: Two short beeps aer scan indicates disable, one long sound with
three tones indicates enable.
IOS Keyboard POP UP/HIDE
Enable/Disable
Enable/Disable
This manual suits for next models
1
Table of contents
Other Netum Barcode Reader manuals
