NETGEAR WNXR2000 User manual
Wireless N 300+ Powerline AV Router
WNXR2000
NETGEAR
Installation Guide
©2010 NETGEAR, Inc. All rights reserved.
Technical Support
Thank you for selecting NETGEAR products.
Locate the serial number on the label of your product and use it to register
your product at http://www.NETGEAR.com/register. Registration is required
before you can use the telephone support service. Registration at the
NETGEAR website is strongly recommended.
Go to http://support.netgear.com for product updates and Web support.
For complete DoC please visit the NETGEAR EU Declarations of
Conformity website at: http://kb.netgear.com/app/answers/detail/a_id/
11621/
Trademarks
NETGEAR, the NETGEAR logo, ProSafe, Smart Wizard, and Auto Uplink
are trademarks or registered trademarks of NETGEAR, Inc. Microsoft,
Windows, Windows NT, and Vista are registered trademarks of Microsoft
Corporation. Other brand and product names are registered trademarks or
trademarks of their respective holders.
Statement of Conditions
In the interest of improving internal design, operational function, and/or
reliability, NETGEAR reserves the right to make changes to the products
described in this document without notice. NETGEAR does not assume
any liability that may occur due to the use or application of the product(s) or
circuit layout(s) described herein.
3
Package Contents
NETGEAR
N300 Wireless Router
Resource CD
Ethernet Cable
Wireless N 300+ Powerline AV Router
WNXR2000
XAVP1000 Y-Cable Adapter
4
About Your WNXR2000
The WNR2000 router works with the XAVP1000 Y-cable
adapter to help you create a Powerline and wireless network.
To set up your network, do the following:
• Set Up the XAVP1000 Adapter
• Connect the WNXR2000 Powerline AV Router
Set Up the XAVP1000 Adapter
Follow these steps to connect the XAVP1000 adapter to the
router:
1. Plug the network connector on the Y-cable adapter into one
of the orange Ethernet ports on the router.
2. Plug the Power connector on the Y-cable adapter into the
power inlet on the router.
3. Plug the XAVP1000 adapter into an electrical outlet.
Make sure that:
• You do NOT plug the adapter into a Power Strip.
• The electrical outlet is not controlled by a wall switch to
avoid someone unknowingly turning off the power to
the outlet.
5
4. Power on the router using the Power On/Off button on the
back of the router.
5. Check that the power lights on both the XAVP1000 adapter
and on the router are lit. For more information on the status
lights, see “WNXR2000 Router Status Lights” on page 15
and “XAVP1000 Adapter LEDs and Buttons” on page 17.
6. When the router indicates that the Ethernet port connected to
the Y-cable adapter is linked and active (the LED for the
Ethernet port on the front of the router will be solid
green), check that the Ethernet and Powerline LEDs
on the adapter are also on and blinking.
Connect the WNXR2000
Powerline AV Router
Follow the connection instructions as shown in the drawing on
the next page.
Step 4:
Modem
DSL
or Cable
Internet
Step 1:
Unplug the power
to turn off your modem.
Step 2:
Connect one end of the
yellow cable ( ) to your
modem, and connect the
other end to your router.
Power on your router.
Wait until the wireless LED
turns on.
6
Step 6:
Insert Your CD.
Click Router Setup and follow
the steps to set up a secure
wireless network.
Step 5:
N300 Wireless Router
(not included)
Power on/off
Resource CD
Laptop or Desktop
Computer
Wireless on/off
WirelessN 300+ Powerline AV Router
WNXR2000
Note: If your laptop does not have a
CD drive, see “No CD Drive” Installation
on the back to complete your router setup.
Step 7:
Connect your Powerline
devices. See next page.
Step 3:
Power on your modem.
Wait until your modem
cycles on (approximately
2 minutes).
Note: If you have a modem with a battery-backup,
remove and re-insert the battery before connecting
your modem to power.
Connect your computer.
Connect with a wired connection
(as shown in this diagram) or
connect wirelessly to the router
with these settings:
Wireless Network (SSID): ______________
Wireless Password: ___________________
7
8
Existing Powerline Network — Room 1 (example)
This drawing (Room 1) shows how the Y-cable Powerline
adapter and WNR2000 router might fit into an existing
Powerline network in your house.
9
Existing Powerline Network — Room 2 (example)
Reset
(additional Powerline
adapters not included)
10
Setting Up Internet Access
1. In the address field of your browser, type http://
www.routerlogin.net and click Enter.
2. Enter the router User Name
admin and default Password
password to open your
router’s main settings page.
3. When the main settings
page opens, you will be
asked if you want to “Check
for Update.” Click Cancel.You can always check for new
firmware later after you are connected to the Internet.
4. Select the first menu item on the left: Setup Wizard. Make
sure Yes is selected. Then click Next and follow the prompts
to complete the Setup Wizard.
When the Setup Wizard has completed detecting your
connection, the Basic Settings page displays showing your
settings. You are now connected to the Internet.
This manual suits for next models
1
Table of contents
Other NETGEAR Wireless Router manuals
NETGEAR
NETGEAR Nighthawk RAX29 User manual
NETGEAR
NETGEAR WGR614 v4 User manual
NETGEAR
NETGEAR RangeMax WPN824 User manual
NETGEAR
NETGEAR JNR3000 Guide
NETGEAR
NETGEAR R6260 User manual
NETGEAR
NETGEAR Orbi RBR750 User manual
NETGEAR
NETGEAR MBRN3000 - 3G/4G Mobile Broadband Wireless-N... User manual
NETGEAR
NETGEAR Nighthawk RAX200 User manual
NETGEAR
NETGEAR WGR614 User manual
NETGEAR
NETGEAR HR314 - Wireless Router User manual
NETGEAR
NETGEAR WGU624 User manual
NETGEAR
NETGEAR Orbi RBS50 User manual
NETGEAR
NETGEAR Nighthawk X10 User manual
NETGEAR
NETGEAR Nighthawk X6S User manual
NETGEAR
NETGEAR WGR614 User manual
NETGEAR
NETGEAR MBRN3000 - 3G/4G Mobile Broadband Wireless-N... User manual
NETGEAR
NETGEAR WNDR3700 - RangeMax Dual Band Wireless-N Gigabit Router... User manual
NETGEAR
NETGEAR Orbi NBR750 User manual
NETGEAR
NETGEAR MR70 User manual
NETGEAR
NETGEAR WPN824v1 - RangeMax Wireless Router Operation manual
