NETGEAR FSM7328S - ProSafe Switch User manual

Other manuals for FSM7328S - ProSafe Switch

7

Table of contents

Other NETGEAR Switch manuals

NETGEAR

NETGEAR GS724T - ProSafe Switch Instruction Manual

NETGEAR

NETGEAR FS308 - Switch User manual

NETGEAR

NETGEAR GS728TS Smart Switch User manual

NETGEAR

NETGEAR MS510TX Manual

NETGEAR

NETGEAR GS508T - Switch User manual

NETGEAR

NETGEAR GSS108E User manual

NETGEAR

NETGEAR ProSafe GS116v2 User manual

NETGEAR

NETGEAR GSM7224R - ProSafe Switch User manual

NETGEAR

NETGEAR ProSafe GS516TP User manual

NETGEAR

NETGEAR GS605v4 User manual

NETGEAR

NETGEAR EN106TP EN106TP EN106TP User manual

NETGEAR

NETGEAR ProSafe GSM5212P Manual

NETGEAR

NETGEAR XS708T User manual

NETGEAR

NETGEAR ProSAFE S3300-28X User manual

NETGEAR

NETGEAR ProSAFE S3300 Manual

NETGEAR

NETGEAR GS724TPS - ProSafe - Gigabit Stackable PoE Smart... User manual

NETGEAR

NETGEAR GS316 User manual

NETGEAR

NETGEAR ProSafe Plus User manual

NETGEAR

NETGEAR XS728T ProSAFE Manual

NETGEAR

NETGEAR JFS516v2 User manual

NETGEAR

NETGEAR GSS108E User manual

NETGEAR

NETGEAR GS105A User manual

NETGEAR

NETGEAR XS728T ProSAFE User manual

NETGEAR

NETGEAR FS728TS - ProSafe Smart Switch User manual

Popular Switch manuals by other brands

URC

URC Total Control MFS-8 installation manual

Azbil

Azbil HPQ-D11 user manual

Sony

Sony DFS-900M operating instructions

SICK

SICK i17S operating instructions

F&F

F&F SZR-277 quick start guide

Shure

Shure UAMS/BK user guide

Dräger

Dräger X-zone Switch Off Instructions for use

Asco

Asco Joucomatic 349 Series manual

BT

BT Mini Hub user guide

D-Link

D-Link DES-1226G manual

Johnson Controls

Johnson Controls FS80-C installation instructions

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Configuration guide

MicroNet

MicroNet SP1200A user manual

Ruijie

Ruijie RG-PF2920 Series Hardware installation and reference guide

Altinex

Altinex DA1914SX user guide

MiLAN

MiLAN MIL-SM2401M user guide

RJM

RJM MASTERMIND PBC/6X user manual

Atlas

Atlas MMK-KVM8 owner's manual

7000 Series (Firmware 6.0.0.15)

Configuring VLANs and Routing

Scenario:

Creation of a 2 VLAN Routed network with access to the Internet via

an FVS Router/Firewall.

VLAN 3 being the Users PC domain

VLAN 2 being the Internet domain

Network Diagram:

Physical Setup:

1x FSM7328S Prosafe Layer 3 Managed switch - Firmware 6.0.0.15

4x Windows XP Computers (2x on each VLAN)

1 x FVS___ Prosafe Firewall Router

Logical Setup:

FVS___ : 192.10.10.1/24

VLAN 2 –192.10.10.0/24

VLAN 3 –172.10.11.0/24

VLAN2 IP address 192.10.10.254

VLAN3 IP address 192.10.11.254

WORKING INSTRUCTIONS

Set the Management IP address

1) Plugged the console cable to the Serial port of the switch and the serial port on the

PC

2) Open a new Hyper Terminal session (connecting via the COM port) –settings 9600,

8 , None , 1, None

3) Power Cycle the switch

4) Upon POST the User: prompt will appear

5) Username is admin , password “blank”

6) Type Enable to access the privileged mode (password “blank” )

7) Type network protocol none to reset the network settings

8) Type network parms <<Management IP>> <<Subnet Mask>> <<Default Gateway

IP>>. For example network parms 192.168.0.1 255.255.255.0 192.168.0.1

9) User copy system:running-config nvram:startup-config to save the configuration

10) Check with show network if the settings are correct

The switch should now be accessible patching a CAT5 Straight-through cable. The PC

NIC must be configured with an IP address within the same subnet used to configure the

management IP of the switch (Example: 192.168.0.2 255.255.255.0

Creating a Routing VLAN2 and Routing VLAN3 via the SmartWizard

1) Access the GUI

2) Browse to Smart Wizard –VLAN routing Wizard

3) Assign the VLAN ID

4) Select the port(s) members of the VLAN (Use CTRL to select multiple ports)

5) Assign the VLAN IP address and Subnet Mask

6) Click on Submit. The UNIT/SLOT/PORT entry will show the Virtual PORT created

and associated to the new VLAN.

7) Perform point 1-6 to create VLAN3 (with relevant IP address)

WEB GUI instructions

Creating a Routing VLAN2 and Routing VLAN3 via the SmartWizard

1) Access the GUI

2) Browse to Smart Wizard –VLAN routing Wizard

3) Assign the VLAN ID

4) Select the port(s) members of the VLAN (Use CTRL to select multiple ports)

5) Assign the VLAN IP address and Subnet Mask

6) Click on Submit. The following statement should be prompted.

7) Perform point 1-6 to create VLAN3 (with relevant IP address)

8) The following summary should be obtained:

Checking routing is in place on the switch

1) Browse to Routing –RIP –Interface Summary

2) The following situation should appear

NOTE: The RIP admin mode will show ENABLE only if at least one active device is

patched into a port in the relevant VLAN

NOTA BENE:

Router/Firewall:

If the firewall as in this case is patched into a port in a specific VLAN (VLAN2 here),

ensure its static routing table contains a route back to the VLAN IP address for each of

the other VLANS on the switch that require Internet access.

For example in this case the FVS Firewall must contain the following route:

192.10.11.0 (Subnet) 255.255.255.0 (Subnet Mask) 192.10.10.254 (Default Gateway).

On the other hand another option would be to run RIP on the Firewall.