Nemco Roll-A-Grill 8230 Series User manual
Model Series: 8230, 8250, Electronic Rollergrills
INTRODUCTION
1. Please read instructions before using.
2. T is roller grill will be HOT during use and for a s ort time after it is turned off – BE CAREFUL!
INSTALLATION
1. Set t e roller grill on a flat surface.
2. Position t e roller grill near t e power outlet. Avoid t e use of extension cords.
3. Plug t e roller grill into a certified electrical outlet wit a corresponding voltage rating as listed on t e
roller grill model label.
4. Clean t e roller grill t oroug ly before use.
OVERVIEW OF CONTROLS
1. T ere is a lig ted rocker switc to turn t e roller grill on.
2. T ere are two zone buttons (front and rear) w ic are also used as up and down buttons during t e
settings mode.
3. T ere are a set of four indicator lig ts for eac zone to indicate w ic p ase of t e cook cycle t at zone is
currently in (pre eat, cook, old – below 160°F, and old – above 160°F)
4. T ere is also a display t at s ows eit er t e time left before t e product is ready to serve, or t e
temperature of t e zone w en t e product is ready to serve.
5. T ere are two indicator lig ts by t e zone buttons to s ow w ic zone t e display is currently s owing.
OPERATION
1. Turn t e switc on to turn t e roller grill on. T e lig ts will all flas w en t e controls power up and t e
rocker switc will t en lig t up.
2. T e display s ows das es to indicate t at no eat cycle is active. At t is point t e product can be placed
on t e rollers and t e appropriate zone button (front or rear) can be pressed to initiate t e cook cycle for
t at zone. T e front and rear of t e grill are denoted by t e two different colors of roller end seals; black
for front, w ite for rear.
3. After pressing t e zone button, t e roller grill will begin a 10 minute pre eat p ase w ic is designed to
be part of t e cook cycle. It will t en automatically adjust t e temperature for t e cook p ase. Once t e
grill completes t e cook p ase, it will automatically adjust t e temperature for t e old p ase.
4. During t e cook p ase, t e grill will display ow muc time is left before t e product is ready (all times
are in ours and minutes). Once t e product is ready, t e display c anges to s ow t e temperature of t e
product. At t is point t e product is ready to serve. Once t e olding time as expired, t e old lig t will
begin to flas to indicate t at t e food is beyond it’s recommended olding time.
Note: T e roller grill will turn on t e appropriate indicator lig t to indicate w ic p ase it is in (pre eat,
cook old).
5. W en bot zones are in operation, t e display of t e grill will cycle from t e front zone to t e rear zone to
display t e status of eac . To see t e status of a zone immediately, tap t at zone’s button and t e display
will c ange to s ow its status.
6. If product as been used up, and t e old cycle needs cancelled, press and old t e appropriate zone
button (front or rear). T e old lig t will t en turn off to indicate t at t e zone is no longer eating.
7. Also, t e operator can skip t e pre eat cycle once it is initiated by pressing and olding t e zone button
(front or rear). T e same can be done wit t e cook cycle.
2
CHANGING THE COOK CYCLE SETTINGS
1. T e front and rear zone cook settings can be set individually. To c ange t e settings of one of t ese
zones, make sure t e grill is on and t e eat zone is off. Press and old t e “Settings” button w ile
pressing t e appropriate zone button (front or rear) and release bot w en t e cook lig ts begin flas ing.
2. T e cook lig t will begin to flas and t e display will s ow t e current cook eat setting. T is is ow
muc eat is applied to t e rollers during t e cook cycle and can be set to any number from 0.00 to 1.00.
T e settings can be adjusted up or down using t e two zone buttons w ic ave up and down arrows on
t em. To advance to t e next setting, press t e “Settings” button.
3. T e next setting is t e cook time (in ours and minutes).
4. After t e cook settings are set, t e old lig ts begin to flas and t e grill s ows t e old eat setting.
5. T e last setting is t e old time (again in ours and minutes).
6. After setting t e old settings, press t e “Settings” button again to exit t e settings mode.
CLEANING
NOTE: Proper maintenance plays an important part in t e life span and functioning of t e roller grill
1. W en t e grill is off, press eac zone button (front and rear) to begin eating t e grill up.
2. Once t e grill is ot, t en t e rollers can be wiped down.
3. ALWAYS START AT THE END OF THE ROLLERS AND WIPE TOWARD THE CENTER. T is prevents
extra grease from entering t e sides of t e roller grill and into t e bearings.
♦GripsIt rollers: Use a wet, soft clot to wipe t e rollers clean. NOTE: never use any metal object on t e
GripsIt rollers at any time. Metal will cause serious damage to t e rollers.
♦Silverstone rollers: Use a scratc proof sponge made for non-stick coated products or a soft clot to
wipe t e rollers clean. If t e build up on t e rollers cannot be removed by just wiping wit a wet
sponge, wrap some ice cubes inside a soft towel and rub over t e rollers. NOTE: never use any metal
object on t e Silverstone rollers at any time. Metal will cause serious damage to t e rollers.
♦C rome rollers: Eac roller grill comes wit a two sided sponge. Use t e roug side of t e sponge to
remove all residue from t e rollers. If build up of residue cannot be removed from t e rollers by
wiping wit a course sponge you may use any type of kitc en abrasive to clean t e rollers.
4. After cleaning t e rollers, remove t e drip pan and clean wit mild soap and water.
SERVICE INSTRUCTIONS
IF ROLLERS WON’T TURN
1. C eck power source to be sure t e roller grill is plugged into t e proper voltage outlet and t at t e outlet
is in proper working order.
2. IMPORTANT: Disconnect t e roller grill from t e power source before disassembly.
3. Remove t e end covers.
4. If t e drive c ain is off t e idler sprocket, reinstall it.
5. Remove t e drive c ain from t e sprocket on t e motor s aft and if t e rollers turn easily, t en replace
t e motor.
6. Remove t e c ain guard and inspect t e sprockets on t e end of eac roller. If t ey are loose, worn, or
out of alignment, t en replace t e roller.
7. If t e rollers are ard to turn by and (wit out t e c ain attac ed) remove and clean out any
accumulated foreign matter in t e bearings and on t e rollers.
8. IMPORTANT: Reassemble t e roller grill completely before reconnecting to t e power source.
IF ROLLER GRILL BLOWS A FUSE OR CIRCUIT BREAKER
1. C eck t e capacity of t e circuit being used to be sure it is not overloaded.
2. Unplug t e roller grill and c eck it’s wiring for s ort circuits.
IF ROLLERS WON’T HEAT
C eck t e power source to be sure t e roller grill is plugged into t e proper voltage outlet and t e receptacle
is working. If properly connected and still no eat call NEMCO customer service at 1-800-782-6761.
NOTE: WARRANTY DOES NOT COVER DAMAGE TO THE ROLLERS OR ROLLER
COATING. IT IS NEMCO'S SOLE DISCRETION TO DETERMINE IF A ROLLER OR
ROLLER COATING CLAIM IS WARRANTED
.
3
NEMCO FOOD EQUIPMENT
301 Meuse Argonne, Hicksville, OH 43526
Phone: (419) 542-7751 Fax: (419) 542-6690 Toll free: 1-800-782-6761 IN82XX
www.nemcofoodequip.com 5-15-12
This manual suits for next models
1
Table of contents
Other Nemco Grill manuals
Popular Grill manuals by other brands
Kenmore
Kenmore 415.16123800 Use and care guide
Camp Chef
Camp Chef PG24CLAU Warning & instruction booklet
Tucker Barbecues
Tucker Barbecues GTR Series Assembly, installation and operating instructions
Monogram
Monogram ZGG540NCP1SS owner's manual
Equipex
Equipex Sodir Savoy Operation manual
Gaggenau
Gaggenau VR 414 610 use and care manual
