Neilsen CT3069 User manual
HOT GLUE GUN CT3069
ORINIAL MANUAL
SAVE THESE INSTRUCTIONS AND PRECAUTIONS.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.UNITED KINGDOM
EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety and
health requirements of the EC Directive based on its design and type, as brought
into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will
lose its validity.
Product description: HOT GLUE GUN
Model: CT3069
Applicable EC Directives:
EC Low Voltage Directive 2006/95/EC
EC Directive of Electromagnetic Compatibility 2014/30/EU
Harmonized standards：
：：
：
EN 60335-2-45, EN 60335-1, EN62233,
EN 55014-1, EN 55014-2,EN 61000-3-2, EN 61000-3-3
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2016-03-03
Due to continuing improvements, actual product may differ slightly from the product
described herein. Tools required for assembly and service may no to included.
SPECIFICATIONS
Glue Gun: 220V-240V/50Hz 40W
UNPACKING
When unpacking, make sure that the item is intact and undamaged.
Check that no parts are missing.
IMPORTANT SAFETY INFORMATION
1. Always wear approved safety goggles and heavy duty work gloves during use.
2. Contains glue; keep away from children. This product is not a toy, do not allow
children to play with or go near this item.
3. Use as intended only.
4. Inspect before every use; do not use if parts are loose or damaged.
5. Maintain product label and name-plates. These carry important safety
information.
6. Always store is a safe, secure place.
7. Keep these instructions for future use.
INSTRUCTIONS
Please read the ENTIRE IMPORTANT SAFETY INFORMATION section at the
beginning of this document including all text under subheadings therein before set
up or use of this product.
GLUE GUN – INSTRUCTIONS FOR USE
The glue sticks to many surfaces including wood, plastic ,paper and cardboard
OPERATION INSTRUCTIONS
Step 1
Insert one of the glue sticks through the
tunnel on the back of the gun
Step 2
Plug cord into an electrical outlet and
wait 5 minutes to heat up the glue.
Then apply the glue by continuously
pressing the trigger.
Step 3
Release the trigger to stop the flow of glue.
Apply pressure on the glued parts for
approximately 60 seconds for complete
bonding.
WARNING / CAUTON:
Do not touch the nozzle or melted glue. Operating temperature of the gun is 150
0
C
Always unplug the cord when the gun is not in use
Keep out of reach of children and store in a safe place.
ELECTRICAL INFORMATION
Warning
Mains plug replacement (UK & Ireland only)
If you need to replace the fitted plug of the tool, then follow the instructions below.
Machines that are connected direct to mains supply.
For machines that are double insulated, do not require a connection to earth.
If in doubt consult a qualified electrician
The wires are coloured as follows
Blue Neutral (N)
Brown Live (L)
3amp BS 1363A Fuse
Always secure the wires in the plug terminals carefully make sure no loose strands
are left exposed as they can short circuit and cause injury, fire and or damaged the
tool.
Secure the cable in the cord grip firmly.
Never use a light socket. Never connect the live (L) or neutral (N) wires to the earth
pin marked (E)
NOTE: If your mains wires differ from the above consult a qualified electrician.
Always make sure the mains supply is of correct voltage and you use the correct
fuse protection
Regularly inspect all machines electrical connection and wiring condition for
damage. Any faults detected should be immediately rectified before further use of
the machine. Always have the wiring checked by a qualified electrician
In use ensure all wiring and extension cords are kept clear of any cutting tools,
sharp objects and any other workshop hazards such as wet floors, chemicals,
solvents etc.
This machine is protected by a 3 amp fuse make sure the correct fuse is used
To prevent fire or shock hazards do not expose these products to rain or moisture.
CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Made in china
Table of contents
Other Neilsen Glue Gun manuals
Popular Glue Gun manuals by other brands
Grizzly
Grizzly T1236 instructions
EINHELL
EINHELL TE-CG 18 Li Original operating instructions
SURTECO
SURTECO Dollken Profiles HKP 2.0 E Instruction handbook
Parkside
Parkside PHPA 20-Li A1 Translation of the original instructions
SURTECO
SURTECO Dollken Profiles HKP 220 Instruction handbook
Dollken
Dollken Profiles HKP 2.0 E Instruction handbook
