NEFF T22S46N0AU User manual

Neff GmbH

Carl-Wery-Stra e 34ß

81739 München

Cod. 900053268

7 A

T22

S46N0A

T26

S66N0A

This cooktop is for use with Natural Gas and Univer

sal LP

Wiring diagram

A. Switch

B. Blue wire

C. Brown wire

D. Terminal

E. Ignition module

Gas type NG

HGC (MJ)

Preinstalled NG

In compliance with AS/NZ 3100 and AS 4551

Made in Spain

Injectors marks

1,0

LHR

118

LHF

160

RHR

155

RHF

2,75

Gas type NG

HGC (MJ)

Preinstalled NG

In compliance with AS/NZ 3100 and AS 4551

Made in Spain

Injectors marks

LHR

118

LHF

RHR

155

RHF

1,0

118

2,75

85/140

46/71

32,90 30,50 45,40 43,50

eff- Gmb

-Nr T22S46N0AU

eff- Gmb

-Nr T26S66N0AU

Test point pressure (kPa) Test point pressure (kPa)

ULPG

GMK 10

032

GMK 10032

Content

Safety considerations . . . . . . . . . . . . . . . . 5

For your safety . . . . . . . . . . . . . . . . . . . . . . . 5

What to do if you smell gas . . . . . . . . . . . . . . 5

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation . . . . . . . . . . . . . . . . . . . . . . . . . 7

Statutory requirements . . . . . . . . . . . . . . . . . . 7

Preparing to install . . . . . . . . . . . . . . . . . . . . . . . 7

Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Installation of cooktop into the kitchen bench . . 9

Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Conversion from Nat. Gas to Universal LPG . . 12

To change injectors . . . . . . . . . . . . . . . . . . . . 12

Changing the nozzles of the burners on the

cooktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Adjustment of the taps . . . . . . . . . . . . . . . . . 13

Operating instructions. . . . . . . . . . . . . . . . 16

Burner locations . . . . . . . . . . . . . . . . . . . . . . . . 16

The gas burners. Operation . . . . . . . . . . . . . . . 16

Switching on automatically . . . . . . . . . . . . . . . 17

Safety system . . . . . . . . . . . . . . . . . . . . . . . . . 17

Switching off a burner . . . . . . . . . . . . . . . . . . . 17

Power levels . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Suitable pans . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Additional wok pan support . . . . . . . . . . . . . . 19

Additional coffee maker support. . . . . . . . . . . 19

Cooking recommendation . . . . . . . . . . . . . . . . 20

Precautions for use. . . . . . . . . . . . . . . . . . . . . . 21

Cleaning and maintenance . . . . . . . . . . . . . . 22

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Unsuitable products . . . . . . . . . . . . . . . . . . 22

Maintenance . . . . . . . . . . . . . . . . . . . . . . . 22

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Wiring diagram . . . . . . . . . . . . . . . . . . . . . . . . 24

Dear customer,

Congratulations on your choice and thank you for purchasing one of our appliances. This

practical, modern and functional appliance is manufactured using materials of the highest

quality which are subject to strict quality control checks throughout the entire manufacturing

process. The appliance is meticulously tested to ensure that it meets your demands and

produces perfect cooking results.

Do not remove the appliance from its protective packaging until it is installed in the unit.

Please read these instructions carefully before proceeding to install and use the appliance.

The information contained in these instructions is essential for the correct operation of the

appliance and, more importantly, for your safety.

The packaging of your appliance has been manufactured using only the materials which are

strictly necessary to guarantee efficient protection during transport.

These materials are 100% recyclable, thus reducing the environmental impact. You can also

contribute to caring for the environment, by following the advice below:

- dispose of the packaging in the appropriate recycling bin

- before you get rid of an old appliance, make sure you disable it. Contact your local authority

to find out the address of your nearest recycling centre to dispose of your appliance

- do not pour used oil down the sink. Collect it in a sealed container and take it to an

appropriate collection point or, failing that, place it in the rubbish bin (it will end up in a

controlled dump; this is probably not the best option, but it will avoid contaminating ground

water)

IMPORTANT:

In the unlikely event that the appliance should be damaged or not meet your expectations

in terms of quality, please inform us as soon as possible. For the warranty to be valid, the

appliance must not have been tampered with, or used inappropriately.

Safety considerations

For your safety If the information in this manual is not followed exactly, a

fire or explosion may result causing property damage,

personal injury or death.

Do not store articles on or against this appliance.

Do not store flammable material near this appliance.

Do not spray aerosols in the vicinity of this appliance

while it is in operation.

What to do if you

smell gas

Do not try to light the appliance.

Do not touch any electrical switch; do not use any phone

in your building.

Inmediately call your gas supplier from a neighbour’s

phone. Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire

department.

Installation and service must be performed by an

authorised person.

Warnings Do not allow the flame to extend beyond the edge of the

cooking utensil. This instruction is based on safety

considerations.

Do not forget that the unit becomes hot when in use.

Common sense is important. Just because the flame is

out, does not mean parts cannot still be hot.

This appliance shall not be used for space heating. This

instruction is based on safety considerations.

Be sure to disconnect the electrical supply before

disassembly of the appliance.

Keep the appliance area clear and free from combustible

materials, gasoline and other flammable vapours and

liquids.

This appliance must be installed in a position with the

proper level of ventilation. Do not obstruct the flow of

combustion and ventilation air.

Cabinets installed above the gas cooktop must have a

minimum clearance of 650 mm (24”).

The gas pressure regulator supplied with the appliance

must be installed in line with the gas pipe. (N.G. only).

For pressure testing in excess of 3.5 kPa (1/2 psig) the

appliance and its individual shutoff valve must be

disconnected from the gas supply piping system.

Important. When using a very large pot, leave a gap of at

least 50 mm (2”) to avoid damaging any parts in bench

top wood, plastic or other non-heat resistant materials.

Never leave oil or hot fat unattended.

The surfaces on heating and cooking appliances get hot

when in use. Be careful. Keep children away from the

appliance.

Only use your appliance for the preparation of food and

never for room-heating purposes.

This appliance leaves the factory set for the gas supply

indicated on the data label. Call the Service Centre if it

needs to be altered.

Do not tamper inside the appliance. If necessary, call

your local Service Centre.

Overheated fat or oil can easily catch fire. Never leave the

appliance unattended when cooking food with fat or oil,

e.g. chips.

Never pour water on burning fat or oil. DANGER OF

BURNS! Cover the receptacle to smother the flames and

turn the cooktop off.

In the event of a fault, cut the gas and electricity supplies

to the appliance. Call our Service Centre to repair the

fault.

Do not use unstable or uneven-based receptacles on

cooking plates or burners. They may accidentally tip over.

If a gas supply knob/valve jams, do not force it. Call your

official Service Centre immediately for them to repair or

replace it.

The illustrations used in this booklet are only intended as

a guide.

Grids become very hot during use. When operating the

appliance control knobs, take care not to make contact

with the grids.

Do not use this appliance neither in marine craft nor in

caravans.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

Make sure you keep these instructions for use and

assembly in a safe place, so that you can hand them on

with the appliance if it ever changes owner.

Note: To avoid jeopardising the electrical safety of the

appliance, it is forbidden to use high-pressure or steam

jet cleaning devices.

SHOULD THE RELEVANT CONDITIONS NOT BE

PROPERLY SATISFIED, THE INSTALLER, AND NOT THE

MANUFACTURER, SHALL HELD LIABLE.

Installation

Statutory

requirements

This installation must conform with the following:

Ø Manufacturer’s Installation instructions

Ø Local Gas Fitting Regulations

Ø Municipal Building Codes,

Ø Refer to AS/NZS 5601.1 for Gas Installations.

Ø S.A.A. Wiring Code

Ø Local Electrical Regulations

Ø Any other statutory regulations

Preparing to install Refer to AS/NZS 5601.1 for piping size details. These

built-in cooktops are intended to be inserted in a

benchtop cutout.

Only an officially authorised technician should connect

the appliance.

Before you begin, turn off the gas and electricity supply.

Installation dimensions are shown in Fig.1/1a.

Fig. 1

Before connecting the unit, check whether the local

connection conditions (type of gas) are compatible with

the unit’s setting. Observe any special conditions

imposed by local suppliers (utilities). The specifications

of this cooktop are stated on the data label located on the

bottom of the cooktop base.

A duplicate data label is supplied for adhesion to an

accessible location near the hotplate if the data label on

the base of the hotplate cannot be accessed when the

hotplate is installed.

Clearances A range hood fitted above the top must be installed

according to the installation instructions for the range

hood. A minimum distance of 650 mm is required for a

range hood and 750 mm for an exhaust fan.

Any adjoining wall surface situated within 200 mm from

the edge of any hob burner must be a suitable non-

combustible material for a height of 150 mm for the

entire length of the hob. Any combustible construction

above the hotplate must be at least 650 mm above the

top of the burner and no construction shall be within

450 mm above the top of the burner.

A minimum depth of 50 mm from the top of the worktop

surface must be provided for the appliance.

Fig. 1a

If the base of the hotplate can be touched, a protecting

shield must be fitted. This shield must be at least 10 mm

from the lowest part of the hotplate and must be capable

of withstanding the appliance temperatures. Minimum

thickness of benchtop is 30 mm. See Fig. 2.

If an oven is positioned below the cooktop the barrier

does not need to be fitted, but a space of 35 mm must

be maintained between the underside of the cooktop and

the top of the oven.

Installation of cooktop

into the kitchen bench

Installation procedure:

Side clearances: If the distance measured from the

periphery of the nearest burner to any vertical surface is

less than 200 mm, the surface shall be protected in

accordance with clauses 6.10.1.2 of AS/NZS 5601.1

1. For cutout dimensions and clearances refer Fig.1.

2. The clips and the adhesive seal (underside of the

cooktop) are already fitted (depending on the model), do

not under any circumstances remove them. The seal

ensures that the entire work surface will be watertight,

and prevents water seepage. In order to fit the appliance

into the kitchen unit, first place the cooktop in the correct

position then loosen each of the clips so that they all turn

freely (it is not necessary to completely undo them).

Insert and centre the cooktop.

Press the sides of the cooktop until it is supported around

its entire perimeter.

Turn the clips and tighten them fully. Fig. 3.

Fig. 2

Fig. 3.

Connection

Electrical An electrical 10 amp socket needs to be within 1 m of the

hotplate to allow electrical connection. The socket must

remain accessible after installation of the appliance.

Important note:

This appliance is connected to the mains (240 VAC) by

means of the connecting lead which must be fixed to the

kitchen unit to prevent it f r o m c o min g i n t o contact with hot

parts of the cooktop (or an oven installed underneath)

and remain accessible after installation of the cooktop.

When making this connection make sure that the lead

cannot come into contact with hot parts of the cooktop.

Important: This appliance must be earthed. When

connecting the cooktop ensure that the earth wire is

connected first and that all wires are connected to the

correct terminals. Fig. 4.

Gas

During the planning stage, consider the position of supply

connections.

The cooktop must be connected to the gas supply with

upstream connection of an isolation valve in accordance

with the respectively valid regulations. We recommend

that the isolation valve be fitted prior to the cooktop to

enable isolation of cooktop from gas supply. The valve

must be easily accessible at all times.

To find out the factory set gas type, see bottom of

cooktop next to gas connection.

Remove plastic cap from gas supply line prior to

installation.

Fit regulator (N.G.) or a test point (Universal LPG) directly

to the R 1/2’’ connection as per Fig. 5. and Fig. 6.

Direction of gas flow is indicated on the rear of the

regulator.

For position of the inlet connection refer Fig.1.

Use pipe compound or thread sealant, properly theaded

pipes and careful assembly procedure so that there is no

cross threading, etc., which might cause damage or

leakage.

Make sure that all connections peformed are free of

leakage.

The manufacturer does not accept any liability for

leakage on connections performed by the installer or if

the L-tube is moved or twisted.

Fig. 4

Other manuals for T22S46N0AU

This manual suits for next models

Table of contents

Popular Oven manuals by other brands

Bosch

Bosch HVA531NS0 instruction manual

Electrolux

Electrolux EOF6P46X user manual

Combi

Combi BLODGETT BC142GDS Specifications

AEG

AEG COMPETENCE 311704300 Installation and operating instructions

Falcon

Falcon DOMINATOR PLUS G3106 Series Servicing instructions

Rational

Rational SCC WE 61G installation manual

Smeg

Smeg DOSPA38X User manuals

Electrolux

Electrolux air-o-convect 20 GN 2/1 user manual

Miele

Miele HR 1954-2 operating instructions

KHIND

KHIND OT50 instruction manual

Henny Penny

Henny Penny Smoker Box installation manual

Lang

Lang ECOD-AP Installation and operation instructions

AEG

AEG BEK455310M user manual

Frigidaire

Frigidaire FNGE90JGR user manual

Hotpoint

Hotpoint FE9 S831 JSH IX user manual

GE Advantium SCB2000 owner's manual

AEG

AEG DE401301DM user manual

DeLonghi

DeLonghi XA660 Directions for use