NEC 78014Y Series User manual

www.DataSheet4U.com

PD78014, 78014Y SUBSERIES

8-BIT SINGLE-CHIP MICROCONTROLLERS

PD78011B

PD78011BY

PD78012B

PD78012BY

PD78013

PD78013Y

PD78014

PD78014Y

PD78P014

PD78P014Y

PD78011B (A)

PD78012B (A)

PD78013 (A)

PD78014 (A)

User’s Manual

Printed in Japan

Document No. U10085EJ7V0UM00 (7th edition)

Date Published October 1997 N

1992

www.DataSheet4U.com

[MEMO]

www.DataSheet4U.com

NOTES FOR CMOS DEVICES

1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS

Note:

Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide

and ultimately degrade the device operation. Steps must be taken to stop generation of

static electricity as much as possible, and quickly dissipate it once, when it has occurred.

Environmental control must be adequate. When it is dry, humidifier should be used. It is

recommended to avoid using insulators that easily build static electricity. Semiconductor

devices must be stored and transported in an anti-static container, static shielding bag or

conductive material. All test and measurement tools including work bench and floor should

be grounded. The operator should be grounded using wrist strap. Semiconductor devices

must not be touched with bare hands. Similar precautions need to be taken for PW boards

with semiconductor devices on it.

2 HANDLING OF UNUSED INPUT PINS FOR CMOS

Note:

No connection for CMOS device inputs can be cause of malfunction. If no connection is

provided to the input pins, it is possible that an internal input level may be generated due

to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or

NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up

or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor,

if it is considered to have a possibility of being an output pin. All handling related to the

unused pins must be judged device by device and related specifications governing the

devices.

3 STATUS BEFORE INITIALIZATION OF MOS DEVICES

Note:

Power-on does not necessarily define initial status of MOS device. Production process of

MOS does not define the initial operation status of the device. Immediately after the power

source is turned ON, the devices with reset function have not yet been initialized. Hence,

power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is

notinitializeduntiltheresetsignalisreceived. Resetoperationmustbeexecutedimmediately

after power-on for devices having reset function.

www.DataSheet4U.com

FIP, IEBus, and QTOP are trademarks of NEC Corporation.

MicrosoftandWindowsareeitherregisteredtrademarksortrademarksofMicrosoftCorporation

in the United States and/or other countries.

IBM DOS, PC/AT, and PC DOS are trademarks of International Business Machines Corporation.

HP9000Series300,HP9000Series700andHP-UXaretrademarks ofHewlett-PackardCompany.

SPARCstation is a trademark of SPARC International, Inc.

SunOS is a trademark of Sun Microsystems, Inc.

Ethernet is a trademark of XEROX Corporation.

NEWS, NEWS-OS are trademarks of SONY Corporation.

OSF/Motif is a trademark of Open Softwear Foundation, Inc.

TRON is an abbreviation of The Real-time Operating system Nucleus.

ITRON is an abbreviation of Industrial TRON.

License not needed :

PD78P014DW, 78P014YDW

The customer must judge the need for license:

PD78011BCW-×××, 78011BGC-×××-AB8,

PD78011BCW(A)-×××, 78011BGC(A)-×××-AB8,

PD78011BYCW-×××, 78011BYGC-×××-AB8,

PD78012BCW-×××, 78012BGC-×××-AB8,

PD78012BCW(A)-×××, 78012BGC(A)-×××-AB8,

PD78012BYCW-×××, 78012BYGC-×××-AB8,

PD78013CW-×××, 78013GC-×××-AB8,

PD78013CW(A)-×××, 78013GC(A)-×××-AB8,

PD78013YCW-×××, 78013YGC-×××-AB8,

PD78014CW-×××, 78014GC-×××-AB8,

PD78014CW(A)-×××, 78014GC(A)-×××-AB8,

PD78014YCW-×××, 78014YGC-×××-AB8,

PD78P014CW, 78P014GC-AB8,

PD78P014YCW, 78P014YGC-AB8

The export of these products from Japan is regulated by the Japanese government. The export of some or all of these

products may be prohibited without governmental license. To export or re-export some or all of these products from a

country other than Japan may also be prohibited without a license from that country. Please call an NEC sales

representative.

www.DataSheet4U.com

Caution Purchase of NEC I2C components conveys a license under the Philips I2C Patent Rights to use

these components in an I2C system, provided that the system conforms to the I2C Standard

Specification as defined by Philips.

The information in this document is subject to change without notice.

Nopart of this documentmaybecopiedorreproduced in any formorbyanymeans without the priorwritten

consentof NEC Corporation. NECCorporationassumesno responsibility foranyerrorswhich may appear

in this document.

NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual

propertyrightsofthirdpartiesbyorarisingfromuseofadevicedescribedhereinoranyotherliabilityarising

from use of such device. No license, either express, implied or otherwise, is granted under any patents,

copyrights or other intellectual property rights of NEC Corporation or others.

While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor

devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to

persons or property arising from a defect in an NEC semiconductor device, customers must incorporate

sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features.

NEC devices are classified into the following three quality grades:

“Standard”, “Special”, and “Specific”. The Specific quality grade applies only to devices developed based

on a customer designated “quality assurance program” for a specific application. The recommended

applicationsofa device depend on its quality grade, asindicatedbelow. Customersmustcheckthequality

grade of each device before using it in a particular application.

Standard: Computers,officeequipment,communicationsequipment,testandmeasurementequipment,

audio and visual equipment, home electronic appliances, machine tools, personal electronic

equipment and industrial robots

Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-

disastersystems,anti-crimesystems,safetyequipmentandmedicalequipment(notspecifically

designed for life support)

Specific: Aircrafts,aerospace equipment, submersiblerepeaters,nuclearreactor control systems,life

support systems or medical equipment for life support, etc.

The quality grade of NEC devices is “Standard” unless otherwise specified in NEC’s Data Sheets or Data

Books.

If customers intend to use NEC devices for applications other than those specified for Standard quality

grade, they should contact an NEC sales representative in advance.

Anti-radioactive design is not implemented in this product.

M7 96.5

The application circuits and their parameters are for reference only and are not intended for use in actual design-ins.

www.DataSheet4U.com

NEC Electronics Inc. (U.S.)

Santa Clara, California

Tel: 408-588-6000

800-366-9782

Fax: 408-588-6130

800-729-9288

NEC Electronics (Germany) GmbH

Duesseldorf, Germany

Tel: 0211-65 03 02

Fax: 0211-65 03 490

NEC Electronics (UK) Ltd.

Milton Keynes, UK

Tel: 01908-691-133

Fax: 01908-670-290

NEC Electronics Italiana s.r.1.

Milano, Italy

Tel: 02-66 75 41

Fax: 02-66 75 42 99

NEC Electronics Hong Kong Ltd.

Hong Kong

Tel:2886-9318

Fax: 2886-9022/9044

NEC Electronics Hong Kong Ltd.

Seoul Branch

Seoul, Korea

Tel: 02-528-0303

Fax: 02-528-4411

NEC Electronics Singapore Pte. Ltd.

United Square, Singapore 1130

Tel:253-8311

Fax: 250-3583

NEC Electronics Taiwan Ltd.

Taipei, Taiwan

Tel: 02-719-2377

Fax: 02-719-5951

NEC do Brasil S.A.

Cumbica-Guarulhos-SP, Brasil

Tel: 011-6465-6810

Fax: 011-6465-6829

NEC Electronics (Germany) GmbH

Benelux Office

Eindhoven, The Netherlands

Tel:040-2445845

Fax: 040-2444580

NEC Electronics (France) S.A.

Velizy-Villacoublay, France

Tel:01-30-67 58 00

Fax: 01-30-67 58 99

NEC Electronics (France) S.A.

Spain Office

Madrid, Spain

Tel: 01-504-2787

Fax: 01-504-2860

NEC Electronics (Germany) GmbH

Scandinavia Office

Taeby, Sweden

Tel: 08-63 80 820

Fax: 08-63 80 388

Regional Information

Some information contained in this document may vary from country to country. Before using any NEC

product in your application, please contact the NEC office in your country to obtain a list of authorized

representatives and distributors. They will verify:

• Device availability

• Ordering information

• Product release schedule

• Availability of related technical literature

• Development environment specifications (for example, specifications for third-party tools and

components, host computers, power plugs, AC supply voltages, and so forth)

• Network requirements

In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary

from country to country.

J97. 8

www.DataSheet4U.com

Main Revisions in This Edition

Pages Description

p. 43, 44, 56, 57 The following subseries were added in sections 1.6 and 2.6, “78K/0 Series Expansion.”

PD78075B,78075BY,780018,780018Y,780058,780058Y,780034,780034Y,780024,780024Y,

78014H, 780964, 780924, 780228, 78044H, 78044F, 78098B, 780973 Subseries

p. 137 through 141 The illustrations were modified in Figures 6-6 and 6-8, “P20, P21, P23 to P26 Block Diagrams”, Figures

6-7 and 6-9, “P22 and P27 Block Diagrams”, and Figure 6-10, “P30 to P37 Block Diagrams”.

p. 215, 219 Figures 9-10 and 9-13, “Square Wave Output Operation Timings” were added.

p. 264, 321 Cautions were added in sections 15.1 and 16.1, “Serial Interface Channel 0 Configuration”.

p. 271, 330 Cautions were added in sections 15.3 and 16.3, “Serial Interface Channel 0 Control Register (2) Serial

operating mode register 0 (CSIM0)”.

p. 287, 310, 348, 371 Cautions were added in sections 15.4.3 and 16.4.3, “(2) (a) Bus release signal (REL), (b) Command

signal (CMD), (11) Cautions on SBI mode”.

p. 421 (3) MSB/LSB switching as the start bit was added in section 17.4.2, “3-wire serial I/O mode operation”.

p. 439 (3) (d) Busy control option, (e) Busy & strobe control option, and (f) Bit slippage detection function in

section 17.4.3 of the former edition were changed to (4) Synchronization control and the description

was improved.

p. 495 Caution was added in Table 22-1, “Differences between

PD78P014, 78P014Y, and Mask ROM

Version”.

p. 521 APPENDIX A DIFFERENCES BETWEEN

PD78014, 78014H, AND 78018F SUBSERIES was added.

p. 528, 529 Windows compatible 5-inch FD products was erased in APPENDIX B DEVELOPMENT TOOLS.

p. 527, 529 The following products were changed from “Under development” to “Developed”.

IE-78000-R-A

ID78K0

The mark shows major revised points.

www.DataSheet4U.com

[MEMO]

www.DataSheet4U.com

PREFACE

Readers This manual has been prepared for user engineers who want to understand the functions of the

PD78014, 78014Y Subseries and design and develop its application systems and programs.

Target subseries are as follows.

•

PD78014 Subseries :

PD78011B, 78012B, 78013, 78014, 78P014

PD78011B(A), 78012B(A), 78013(A), 78014(A)

•

PD78014Y Subseries:

PD78011BY, 78012BY, 78013Y, 78014Y, 78P014Y

Caution Of the above members, the

PD78P014DW, 78P014YDW should be used only

for experiment or function evaluation, because they are not intended for use in

equipment that will be mass-produced and do not have enough reliability.

Purpose ThismanualisintendedtohelpusersunderstandthefunctionsdescribedfollowingtheOrganization

below.

Organization The

PD78014,78014YSubseriesmanualisseparatedintotwoparts: thismanualandInstructions

(common to the 78K/0 Series)

PD78014, 78014Y SUBSERIES 78K/0 SERIES

USER’S MANUAL USER’S MANUAL

(This manual) – Instructions –

• Pin functions • CPU functions

• Internal block functions • Instruction set

• Interrupts • Explanation of each instruction

• Miscellaneous on-chip peripheral functions

How to Read This Manual

Before reading this manual, you must have general knowledge of electric and logic circuits and

microcontrollers.

When using this manual as the one for the

PD78011B(A), 78012B(A), 78013(A), 78014 (A):

→The

PD78011, 78012B, 78013, 78014 and the

PD78011B(A), 78012B(A), 78013(A),

78014(A) are different only inquality grade. For products (A), regard the product name as

follows.

PD78011B →

PD78011B(A)

PD78012B →

PD78012B(A)

PD78013 →

PD78013(A)

PD78014 →

PD78014(A)

To understand the functions in general:

→Read this manual in the order of the contents.

To interpret the register format:

→For the circled bit number, the bit name is defined as a reserved word in RA78K/0, and

in CC78K/0, already defined in the header file named sfrbit.h.

www.DataSheet4U.com

To confirm the details of the register whose register name is known:

→Refer to APPENDIX D REGISTER INDEX.

For the details of the

PD78014, 78014Y Subseries instruction function:

→Refer to the 78K/0 SERIES USER’S MANUAL, Instructions. (IEU1372).

For the electrical specifications of the

PD78014, 78014Y Subseries:

→Refer to Data Sheet.

For the application examples of

PD78014, 78014Y Subseries functions:

→Refer to Application Note.

Caution The use examples in the manual apply to the general electric devices of the standard quality grade.

Touse the use examplesin the manualfor applications requiring thespecial quality grade, examine

the quality grade of the actually used parts and circuits.

This manual suits for next models

Table of contents

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide

Silicon Laboratories

Silicon Laboratories C8051F800 user guide