NCE NCE897DVD User manual
NCE897DVD
USER MANUAL
RV AUDIO SYSTEM
Please read this manual carefully prior to installation
Single Din Flip down panel
DVD/CD/AM/FM/Multimedia player
Remote
4x50 Watt High Power Out
Bluetooth Audio Streaming
USB/SD/3.5mm AUX Input
C
CONTENTS
Installation steps 1-3
Controls 4-7
Radio operation 8
USB operation 8
Clock operation 8
SD Card operation 9
AUX input operation 9
Sound control 9
Bluetooth operation 10
Troubleshooting 11
Specifications 12
Warranty 13
PL ASTIC TR IM
SERVICE KEYS
O P E N bu tto n
CRADLE
UNIT
1
1. Remove the unit from the cradle as follows.
a. Remove the plastic trim.
b. Insert service keys and then slide the cradle off as illustrated below.
2. Complete all wiring as per instructions on page 2.
3. Remove the control panel from the unit as follows.
a. Press the release button (18) to open the control panel.
b. Hold the right end of the control panel and pull to the right a little
then remove it.
INSTALLATION STEPS
2
In s ta lla tio n d ia g ra m
DASH BO AR D
M E TA L M O UNTING
S TRA P
HEX NUT
PLAIN WASHER
TAPPING SCR EW
CO N SO LE
SLIDE BRACKET
HO U SIN G
HEX BO LT
Make all electrical connections as follows.
Notes:
a. You must only connect one 4ohm speaker per speaker connection.
b. Red ACC wire must be connected to a switched power source.
c. Never connect the yellow B+ wire and red ACC wires together.
d. Any device connected to the blue ANT wire must not exceed 200mA.
INSTALLATION STEPS
RIGHT REAR
SPEAKER +
RIGHT FRONT
SPEAKER +
RIGHT REAR
SPEAKER -
RIGHT FRONT
SPEAKER -
LEFT FRONT
SPEAKER +
LEFT FRONT
SPEAKER -
LEFT REAR
SPEAKER +
LEFT REAR
SPEAKER -
AUTOMATIC
ANTENNA
OUTPUT 12+
IGNITION
12V +
CONSTANT
12V +
GROUND
12V -
3
B u l g e
H o l l o w
B u l g e
H o l l o w
P a n e l C o n n e c t o r
a. Flip the control panel up untill you hear a click sound this indicates that
the control panel is latched onto the unit.
4. Attach the control panel onto the unit as illustrated below.
* Frequent detachment, opening and closing of the control panel will cause
panel connections to accumilate dirt and dust. It is recommended that you
periodically gently wipe the connections with a clean, dry, soft cloth.
5. Plug in your wiring harness and test that all functions work correctly.
6. Install the main unit according to the installation diagram on page 2.
a. Slide the cradle into the dash cavity.
b. Bend tabs of the cradle where necessary to ensure the cradle is secure.
c. Slide the unit into the cradle.
d. Use the metal strap to secure the unit at the rear if possible.
INSTALLATION STEPS
4
UNIT WITH REMOVED CONTROL PANEL
1. Mode button
2. Play/ Pause or station 1 preset button
3. Intro or station 2 preset button
4. Repeat or station 3 preset button
5. Random or station 4 preset button
6. -10 or station 5 preset button
7. +10 or station 6 preset button
8. Clock button
9. SD card slot
10. Volume knob
11. Forward button
12. Back button
13. Band button
14. Preset station Auto
scan.
15. Mute button
16. USB input
17. 3.5mm AUX input
18. Open panel button
19. Reset button
20. Disc slot
21. Disc Eject
CONTROLS
1 2 34
5 6 78
9
10 11121314
15
16
17
18
19
20
21
5
1. Mode
Press the Mode button to switch between Tuner, USB, SD Card,
Bluetooth, Disc, Aux. Please note that if there is no USB or Card device
inserted you will not be able to select that function.
2. Preset 1/Play pause
In radio mode , long press to store the displayed radio station, short
press to retrive the radio station programmed. In SD, USB or Disc mode
press to play or pause the track.
3. Preset 2/Intro
In radio mode , long press to store the displayed radio station, short
press to retrive the radio station programmed. In SD, Disc or USB mode
press to play the first few seconds of the track.
4. Preset 3/Repeat
In radio mode , long press to store the displayed radio station, short
press to retrive the radio station programmed. In SD, Disc or USB mode
press to repeat the current track.
5. Preset 4/Random
In radio mode , long press to store the displayed radio station, short
press to retrive the radio station programmed. In SD, Disc or USB mode
press to play the selected source tracks randomly.
6. Preset 5/-10
In radio mode , long press to store the displayed radio station, short
press to retrive the radio station programmed. In SD, Disc or USB mode
press to move back tracks in multipals of 10 for exemple if you are on
track 50 press 3 times to go to track 20. Long press to move back
through folders.
7. Preset 6/+10
In radio mode , long press to store the displayed radio station, short
press to retrive the radio station programmed. In SD, Disc or USB mode
press to move tracks forward in multipals of 10 for example to go to
track 30 press 3 times. Long press to move forward through folders.
CONTROLS
6
8. Clock
Press to display the time, in tuner mode press and hold to
adjust the clock, the time will flash. Use the volume button (10),
anticlockwise to adjust the hour and clockwise to adjust the minute.
Once completed wait a few seconds and the clock will store.
9. SD card slot
Insert the SD card to automatically begin playback of the sd card.
(Please note some files may not play if this happens please reconfigure
tracks into different formats)
10. Volume knob
Rotate to adjust volume up and down, press the button to toggle
between BASS-TREBLE-BALANCE-FADER use the knob clockwise and
anticlockwise to adjust these features.
11. Forward
In radio mode long press to auto search to the next available radio
station or short press to manually search for radio stations (this
feature is usefull when in low signal areas. In USB, Disc, BT audio and
SD mode short press to move forward to the next track long press to
move forward into the track.
12. Back
In radio mode long press to auto search to the previous available radio
station or short press to manually search for radio stations (this
feature is usefull when in low signal areas. In USB, Disc, BT audio and
SD mode short press to move back to the previous track long press to
move back through the track.
13. Band/End call
Press to toggle between the radio bands, F1 (FM1) - F2 (FM2) -
F3 (FM3) - M1 (AM1) - M2 (AM2) in each band you are able to preset
6 radio station giving you a total 18FM presets and 12AM presets.
CONTROLS
7
14. Preset station scan / Answer
Press to automatically scan all your preset stations.
15. Power / Mute
Press to turn the unit on, long press to turn the unit off. In on position
press to mute the volume, press again to reinstate the volume.
16. USB slot
Open the cover to expose the USB slot. Insert your usb device, this
will begin to playback automatically. (Note some files may not play if
this happens please reconfigure tracks into different formats).
17. 3.5mm AUX input
Plug in your 3.5mm cable into your device then into the unit, press the
mode button to select AUX. (Note that the volume of your device will
directly affect the volume of the output from the unit so take caution).
18. Panel open
Press to open the panel so it can be removed to either insert an SD
card or for security.
19. Reset switch
With a sharp object push the reset button to return the unit to factory
defaults. (Note you will loose all saved preferences).
CONTROLS
8
Radio operation
Turn on the unit by pressing button 1 (Once installed the unit will
turn on and off automatically with your ignition). Press button 1 again
to select the radio mode and button 13 to select the band. You can
then use the forward and back buttons 11 and 12 to select your desired
stations. You can use buttons 2-7 to preset your radio stations, to
preset your desired station firstly choose the station you wish to
programe then hold down one of the buttons from 2-7 to program
into that particular location.
USB operation
Turn on the unit by pressing button 1 (Once installed it will
turn on and off automatically with your ignition). Open the USB panel
exposing the USB connection, plug in your USB device. Press button 1
to select USB mode it will begin to playback automatically (Dependent
on your device), use forward and back buttons 11 and 12 to navigate
through your tracks, press buttons 6 and 7 to move forward and back in
10 track incraments. Long press buttons 6 and 7 to move forward and
back through folders. To remove your device press button 2 to stop
playback then remove device. Should the unit fail to playback contents
of your device it is possible that the recorded format is not supported,
there are many different types of formats some even sharing the same
main name, if this occurs try changing the format of your recordings.
Clock operation
To setup the clock, in tuner mode press button 8 to display the time
press and hold the to adjust the clock, the time will flash. Use the
button (10), anticlockwise to adjust the hour and clockwise to adjust
the minute. Once completed wait a few seconds and the clock will store.
OPERATIONS
Table of contents
Other NCE Ventilation Hood manuals
