Nautel VS2.5 User manual
VS2.5 Transmitter
Installation Manual
Document:NHB-VS2.5-INS
Issue: 11.0 2019-05-10
Status: Standard
Nautel Limited
10089 Peggy’s Cove Road
Hackett’s Cove, NS Canada B3Z 3J4
Phone: +1.902.823.3900 or
Toll Free: +1.877.6NAUTEL (6628835) (Canada & USA only)
Fax: +1.902.823.3183
Nautel Inc.
201 Target Industrial Circle
Bangor, Maine USA 04401
Phone: +1.207.947.8200
Fax: +1.207.947.3693
Customer Service (24 hour support)
+1.877.628.8353 (Canada & USA only)
+1.902.823.5100 (International)
Email: [email protected]
Web: www.nautel.com
The comparisons and other information provided in this document
have been prepared in good faith based on publicly available
information. The reader is encouraged to consult the respective
manufacturer's most recent published data for verification.
© Copyright 2019 NAUTEL. All rights reserved.
VS2.5 Installation Manual Table of contents
Page v
Contents
Release control record vii
Preparing for installation 1-1
Mounting the transmitter 2-1
Connecting to station reference ground 3-1
Installing the RF feed line 4-1
Connecting ac power 5-1
Installing the ac entrance box 5-3
Installing program inputs 6-1
Planning 6-1
Connecting cables 6-1
Installing control and monitoring wiring 7-1
Planning 7-1
Connecting cables 7-1
Commissioning 8-1
Pre-Commissioning 8-2
Commissioning 8-3
Network Setup 8-7
Changing the OS Password 8-9
VS2.5 Installation Manual Table of contents
Page vi Issue 11.0 2019-05-10
Parts and tools 9-1
Contacting Nautel 9-1
Parts supplied by Nautel 9-2
Parts not supplied by Nautel 9-2
Parts ordering 9-2
Module replacement program 9-3
Tools for installation 9-3
Pre-installation / Installation assistance 10-1
Pre-installation consulting 10-1
Installation and commissioning service 10-1
Online documentation 10-3
On-site support 10-3
Training 10-4
Standard warranty 10-5
Extended warranties 10-8
List of terms 11-1
VS2.5 Installation Manual
Issue 11.0 2019-05-10 Page vii
Release control record
Issue Date Reason
11.0 2019-05-10 Hardware Release 11 (NARF66I/04 and NARF66I/05).
Supports software version VS SW 5.2 and higher.
VS2.5 Installation Manual
Page viii Issue 11.0 2019-05-10
VS2.5 Installation Manual Preparing for installation
Issue 11.0 2019-05-10 Page 1-1
Section 1: Preparing for installation
Before installing your VS2.5 transmitter, perform the following steps:
1. Ensure that you have performed the pre-installation tasks described in the
VS2.5 Pre-installation Manual.
2. Inspecttheshippingboxfordamage.ReportanydamageimmediatelytoyourNautelsales
representative and the carrier.
3. Unpack the box. Remove all items from packing and place them on a suitable work
area. Check your packing list to make sure that you received all the components,
including the VS2.5, VS2.5 Quick Start Guide, VS2.5 USB device (contains technical
manual set and unpacking/installation video), installation kit and ancillary kit.
4. Assemble your parts and tools. For a list of required tools, see “Parts and tools” on
page 9-1.
5. When you are ready to install the VS2.5 transmitter, follow the steps shown in
Figure 1.1 on page 1-2.
TIP When you have completed a task or step, put a check mark beside the step
number.
Note:
The VS2.5 Quick Start Guide provides a more streamlined method to unpack,
install and commission your transmitter. If you used the Quick Start Guide to
successfully commission your transmitter, Nautel recommends you use the
information in this Installation Manual to verify your installation or for more in-
depth information, as required.
CAUTION:
FAILURE TO COMPLY WITH RECOMMENDATIONS MAY VOID YOUR MANUFACTURER’S
WARRANTY. FOR MORE INFORMATION, REVIEW YOUR WARRANTY DOCUMENTS.
VS2.5 Installation Manual Preparing for installation
Page 1-2 Issue 11.0 2019-05-10
Figure 1.1: Flowchart - Installing the transmitter
Mounting the transmitter - see page 2-1
Connecting to station reference ground - see page 3-1
Installing control and monitoring wiring - see page 7-1
Commissioning - see page 8-1
Perform operational tasks:
“Commissioning” and “Going On-Air”, beginning on page 8-3
Installing the RF feed line - see page 4-1
Installing program inputs - see page 6-1
Connecting ac power - see page 5-1
Other manuals for VS2.5
2
Table of contents
Other Nautel Transmitter manuals
Nautel
Nautel VS300 User manual
Nautel
Nautel VX150 User manual
Nautel
Nautel NX15 User manual
Nautel
Nautel NV20LT User manual
Nautel
Nautel XR12 Programming manual
Nautel
Nautel NX50 User manual
Nautel
Nautel GV30N Programming manual
Nautel
Nautel VS2.5 Programming manual
Nautel
Nautel VS300 User manual
Nautel
Nautel XR6 Programming manual
Nautel
Nautel VS300 Programming manual
Nautel
Nautel NV5 Programming manual
Nautel
Nautel ND500II Manual
Nautel
Nautel NV30LT-N Manual
Nautel
Nautel XR3 User manual
Nautel
Nautel J1000 Operating instructions
Nautel
Nautel NX50 User manual
Nautel
Nautel NX5 AM User manual
Nautel
Nautel NX15 User manual
Nautel
Nautel VS1 User manual
Popular Transmitter manuals by other brands
Dejero
Dejero EnGo 3x manual
Rosemount
Rosemount 4600 Reference manual
Speaka Professional
Speaka Professional 2342740 operating instructions
trubomat
trubomat GAB 1000 instruction manual
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 instructions
Rondish
Rondish UT-11 quick start guide
