National Instruments 9219 User manual

GETTING STARTED GUIDE

NI 9219

100 S/s/channel, 4-Channel C Series Universal

Analog Input Module

This document explains how to connect to the NI 9219.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9219. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9219 only as described in this document.

Caution This icon denotes a caution, which advises

you to consult documentation where this symbol is

marked.

Caution Do not operate the NI 9219 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

2| ni.com | NI 9219 Getting Started Guide

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

Hazardous Voltage This icon denotes a warning

advising you to take precautions to avoid electrical

shock.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the device, take the

following precautions. A hazardous voltage is a voltage greater

than 42.4 Vpk voltage or 60 V DC to earth ground.

Caution Ensure that hazardous voltage wiring is

performed only by qualified personnel adhering to local

electrical standards.

Caution Do not mix hazardous voltage circuits and

human-accessible circuits on the same module.

Caution Ensure that devices and circuits connected to

the module are properly insulated from human contact.

Caution When terminals are hazardous live, you must

ensure that devices and circuits connected to the

NI 9219 Getting Started Guide | © National Instruments | 3

module are properly insulated from human contact. You

must use the NI 9972 backshell kit to ensure that the

terminals are not accessible.

Safety Voltages

Connect only voltages that are within the following limits.

Isolation

Channel-to-channel

Continuous 250 V AC, Measurement

Category II

Withstand 1,500 V AC, verified by a 5 s

dielectric withstand test

Channel-to-earth ground

Continuous 250 V AC, Measurement

Category II

Withstand 3,000 V AC, verified by a 5 s

dielectric withstand test

4| ni.com | NI 9219 Getting Started Guide

Zone 2 hazardous locations applications

Channel-to-

channel and

channel-to-earth

ground

60 V DC, Measurement

Category I

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Note Measurement Categories CAT I and CAT O are

equivalent. These test and measurement circuits are for

other circuits not intended for direct connection to the

MAINS building installations of Measurement

Categories CAT II, CAT III, or CAT IV.

Measurement Category II is for measurements performed on

circuits directly connected to the electrical distribution system.

This category refers to local-level electrical distribution, such as

NI 9219 Getting Started Guide | © National Instruments | 5

that provided by a standard wall outlet, for example, 115 V for

U.S. or 230 V for Europe.

Caution When using the NI 9219 above 2,000 m or in

explosive atmospheres, do not connect to signals or use

for measurements within Measurement Categories II,

III, or IV.

Caution Do not connect the NI 9219 to signals or use

for measurements within Measurement Categories III

or IV.

Safety Guidelines for Hazardous Locations

The NI 9219 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

Gc and Ex nA IIC T4 Gc hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9219 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

6| ni.com | NI 9219 Getting Started Guide

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2, or Zone 2.

Caution The system must be installed in an enclosure

certified for the intended hazardous (classified)

location, having a tool secured cover/door, where a

minimum protection of at least IP54 is provided.

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9219 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO 07 ATEX 0626664X and is IECEx UL 14.0089X

certified. Each NI 9219 is marked II 3G and is suitable for use

in Zone 2 hazardous locations, in ambient temperatures of -40 °C

≤ Ta ≤ 70 °C. If you are using the NI 9219 in Gas Group IIC

hazardous locations, you must use the device in an NI chassis that

has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or

Ex nL IIC T4 equipment.

NI 9219 Getting Started Guide | © National Instruments | 7

Caution Transient protection shall be provided that is

set at a level not exceeding 140% of the peak rated

voltage value of 85 V at the supply terminals to the

equipment.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC/EN 60664-1.

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

limits provide reasonable protection against harmful interference

8| ni.com | NI 9219 Getting Started Guide

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

product in strict accordance with the instructions in the product

documentation.

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance,

operate this product only with shielded cables and

accessories.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and search

NI 9219 Getting Started Guide | © National Instruments | 9

for the LR certificate, or look for the Lloyd’s Register mark on

the product.

Notice In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

and cables to ensure that the desired EMC performance

is attained.

Preparing the Environment

Ensure that the environment in which you are using the NI 9219

meets the following specifications.

Operating temperature

(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 70 °C

Operating humidity

(IEC 60068-2-78)

10% RH to 90% RH,

noncondensing

Pollution Degree 2

Maximum altitude 2,000 m

10 | ni.com | NI 9219 Getting Started Guide

Other manuals for 9219

Table of contents

Other National Instruments I/O System manuals

National Instruments

National Instruments NI REM-11115 User manual

National Instruments

National Instruments PXI-7830R User manual

National Instruments

National Instruments 9213E User manual

National Instruments

National Instruments DAQPad-6508 User manual

National Instruments

National Instruments NI-9244 User manual

National Instruments

National Instruments NI 6581 User manual

National Instruments

National Instruments NI 9219E User manual

National Instruments

National Instruments SC Express Series User manual

National Instruments

National Instruments 7831R User manual

National Instruments

National Instruments NI 9231 Manual

National Instruments

National Instruments NI USB-6008 User manual

National Instruments

National Instruments PCIe-7820R User manual

National Instruments

National Instruments BNC-2090A User manual

National Instruments

National Instruments PXIe-4339 User manual

National Instruments

National Instruments 6738 Manual

National Instruments

National Instruments SCB-68 User manual

National Instruments

National Instruments SCC-PWR01 User manual

National Instruments

National Instruments USB-6221 OEM User manual

National Instruments

National Instruments PXIe-7856R User manual

National Instruments

National Instruments CB-2162 User manual

National Instruments

National Instruments AT-MIO-16D User manual

National Instruments

National Instruments NI 9437 User manual

National Instruments

National Instruments SCC-AI Series User manual

National Instruments

National Instruments NI 9411 User manual

Popular I/O System manuals by other brands

WAGO

WAGO 750-344 manual

Teknim

Teknim TWM-1887 Installation & user manual

Intelligent Appliance

Intelligent Appliance IA-2662-E user manual

BERGHOF

BERGHOF ECC DIO 16/16 User handbook

Advantech

Advantech PCM-27J3AU Startup manual

Festo

Festo CP-E08-M12-CL manual

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 user guide

Hitachi

Hitachi HX-RIO3 Series user manual

NUUO

NUUO SCB-A08 user manual

M-system

M-system R3Y-RS8 instruction manual

jablotron

jablotron JB-110N user manual

Omron

Omron SYSMAC C200H Operation guide

DOLD

DOLD SAFEMASTER M Safety Technique

ABB

ABB OPT-MF-001 user manual

Omron

Omron SYSMAC C2000H Operation guide

Helmholz

Helmholz TB20 manual

ICP DAS USA

ICP DAS USA tM-AD2 quick start

Automationdirect.com

Automationdirect.com DL305 manual