National Instruments 9472 User manual

(217) 352-9330 | [email protected] | artisantg.com

ARTISAN

TECHNOLOGY

GROUP

Your definitive source

for

quality

pre-owned

equipment.

Artisan Technology

Group

Full-service,

independent

repair

center

with

experienced

engineers

and

technicians

on staff.

buy

your

excess,

underutilized,

and

idle

equipment

along

with

credit

for

buybacks

and

trade-ins

Custom

engineering

your

equipment

works

exactly as

you

specify.

•

Critical

and

expedited

services

•

Leasing

Rentals/

Demos

• In

stock/

Ready-to-ship

•

!TAR-certified

secure

asset

solutions

Expert

team

ITrust

guarantee

100%

satisfaction

All

ademarks,

names, a

s a

earing here

are

e property of

pecti

ner

Find the National Instruments NI 9472 at our website: Click HERE

OPERATING INSTRUCTIONS AND SPECIFICATIONS

NI 9472/9474

8-Channel Digital Output Modules

ni.com/manuals

DeutschFrançais

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

NI 9472/9474 2 ni.com

This document describes how to use the National Instruments 9472

and National Instruments 9474 and includes specifications and

terminal or pin assignments. In this document, the NI 9472/9474

with screw terminal and NI 9472 with DSUB are referred to

inclusively as the NI 9472/9474. Visit ni.com/info and enter

rdsoftwareversion to determine which software youneed for

the modules youare using. For information about installing,

configuring, and programming the system, refer to the system

documentation. Visit ni.com/info and enter cseriesdoc for

information about C Series documentation.

Note The safety guidelines and specifications in this

document are specific to the NI 9472/9474. The other

components in the system might not meet the same safety

ratings and specifications. Refer to the documentation for

each component in the system to determine the safety

ratings and specifications for the entire system. Visit

ni.com/info and enter cseriesdoc for information

about C Series documentation.

Safety Guidelines

Operate the NI 9472/9474 only as described in these operating

instructions.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Hot Surface This icon denotes that the component may be

hot. Touching this component may result in bodily injury.

Safety Guidelines for Hazardous Voltages

Yo ucan connect hazardous voltages only to the NI 9472/9474 with

screw terminal. Do not connect hazardous voltages to the NI 9472

with DSUB.

If hazardous voltages are connected to the module, take the

following precautions. A hazardous voltage is a voltage greater

than 42.4 Vpk or 60 VDC to earth ground.

Caution Ensure that hazardous voltage wiring is

performed only by qualified personnel adhering to local

electrical standards.

Caution Do not mix hazardous voltage circuits and

human-accessible circuits on the same module.

Caution Make sure that devices and circuits connected to

the module are properly insulated from human contact.

Caution When module terminals are hazardous voltage

LIVE (>42.4 Vpk/60 VDC), youmust ensure that devices

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

NI 9472/9474 4 ni.com

and circuits connected to the module are properly

insulated from human contact. Youmust use the NI 9932

connector backshell kit to ensure that the terminals are

not accessible.

Figure 1 shows the NI 9932 connector backshell.

Note Yo ucan use the NI 9932 connector backshell only

with the NI 9472/9474 with screw terminal.

Figure 1. NI 9932 Connector Backshell

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Safety Guidelines for Hazardous Locations

The NI 9472/9474 is suitable for use in Class I, Division 2,

Groups A, B, C, D, T4 hazardous locations; Class I, Zone 2,

AEx nC IIC T4 and Ex nC IIC T4 hazardous locations; and

nonhazardous locations only. Follow these guidelines if youare

installing the NI 9472/9474 in a potentially explosive environment.

Not following these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or connectors

unless power has been switched off or the area is known

to be nonhazardous.

Caution Do not remove modules unless power has been

switched off or the area is known to be nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2.

Caution For Zone 2 applications, install the system in an

enclosure rated to at least IP 54 as defined by IEC 60529

and EN 60529.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

NI 9472/9474 6 ni.com

Caution For Zone 2 applications, install a protection

device between the Vsupand COM terminals on the

NI 9472/9474. The device must prevent the input

Vsup-to-COM voltage from exceeding 42 V if there is a

transient overvoltage condition.

Special Conditions for Hazardous Locations Use in Europe

This equipment has been evaluated as EEx nC IIC T4 equipment

under DEMKO Certificate No. 03 ATEX 0324020X. Each module

is marked II 3G and is suitable for use in Zone 2 hazardous

locations. If youare using the NI 9472/9474 in Gas Group IIC

hazardous locations or in ambient temperatures of

–40 °C ≤Ta ≤70 °C, youmust use the device in an NI chassis that

has been evaluated as EEx nC IIC T4, Ex nA IIC T4, or

Ex nL IIC T4 equipment.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

Special Conditions for Marine Applications

Some modules are Lloyd’s Register (LR) Type Approved for

marine applications. To verify Lloyd’s Register certification, visit

ni.com/certification and search for the LR certificate, or

look for the Lloyd’s Register mark on the module.

Caution To meet radio frequency emission requirements

for marine applications, use shielded cables and install

the system in a metal enclosure. Suppression ferrites

must be installed on power supply inputs near power

entries to modules and controllers. Power supply and

module cables must be separated on opposite sides of the

enclosure and must enter and exit through opposing

enclosure walls.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

NI 9472/9474 8 ni.com

Connecting the NI 9472/9474

The NI 9472/9474 provides connections for eight digital output

channels.

Figure 2. NI 9472/9474 Terminal and Pin Assignments

DO0

DO1

DO2

DO3

DO4

DO5

DO6

DO7

Vsup

COM

Vsup

COM

Vsup

COM

Vsup

COM

Vsup

COM

DO0

Vsup

DO1

DO2

Vsup

DO3

DO4

Vsup

DO5

DO6

Vsup

DO7

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

The NI 9472/9474 with screw terminal has a 10-terminal,

detachable screw-terminal connector. The NI 9472 with DSUB has

a 25-pin DSUB connector. Each channel of the NI 9472/9474 has

a terminal or pin, DO, to which youcan connect a device. The

eight digital output channels are internally referenced to the

common terminal or pin, COM. National Instruments recommends

youprovide independent COM and Vsup wiring for each channel of

the NI 9472 with DSUB to minimize current flow in the COM and

Vsup wiring. The COM pins on the NI 9472 with DSUB are

internally connected..

Note Yo umust use 2-wire ferrules to create a secure

connection when connecting more than one wire to a

single terminal on the NI 9472/9474 with screw terminal.

Each channel has an LED that indicates the state of the channel.

When a channel LED is lit, the channel is on. When the LED is

dark, the channel is off. The LEDs are disabled when the chassis is

in sleep mode. Refer to the Sleep Mode section for more

information about sleep mode.

Artisan Scientific - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisan-scientific.com

This manual suits for next models

Table of contents

Other National Instruments Control Unit manuals

National Instruments

National Instruments NI ISM-7401 User manual

National Instruments

National Instruments NI PXIe-4080 User manual

National Instruments

National Instruments NI 4472 User manual

National Instruments

National Instruments NI-9208 Manual

National Instruments

National Instruments SCC-FV01 User manual

National Instruments

National Instruments 5174 User manual

National Instruments

National Instruments NI 9882 User manual

National Instruments

National Instruments IMAQ PXI-1428 User manual

National Instruments

National Instruments NI 9212 User manual

National Instruments

National Instruments NI 9218 User manual

National Instruments

National Instruments sbRIO-9609 User manual

National Instruments

National Instruments NI 9401 User manual

National Instruments

National Instruments PXI-8214 User manual

National Instruments

National Instruments NI 9203 Manual

National Instruments

National Instruments NI 9247 User manual

National Instruments

National Instruments TB-4304 User manual

National Instruments

National Instruments NI 9237 User manual

National Instruments

National Instruments NI 5772R User manual

National Instruments

National Instruments NI 9225 Manual

National Instruments

National Instruments PXIe-8246 User manual

National Instruments

National Instruments NI 9436 User manual

National Instruments

National Instruments SCXI SCXI-1102 User manual

National Instruments

National Instruments NI 6585 User manual

National Instruments

National Instruments NI MID-7604 Installation guide

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual