National Instruments 9266 User manual

GETTING STARTED GUIDE

NI 9266

8 AO, 0 mA to 20 mA, 16 Bit Simultaneous

This document explains how to connect to the NI 9266. In this

document, the NI 9266 with screw terminal and the NI 9266 with

DSUB are referred to inclusively as the NI 9266.

Note Before you begin, complete the software and

hardware installation procedures in your chassis

documentation.

Note The guidelines in this document are specific to

the NI 9266. The other components in the system might

not meet the same safety ratings. Refer to the

documentation for each component in the system to

determine the safety and EMC ratings for the entire

system.

Safety Guidelines

Operate the NI 9266 only as described in this document.

Caution This icon denotes a caution, which advises

you to consult documentation where this symbol is

marked.

2| ni.com | NI 9266 Getting Started Guide

Caution Do not operate the NI 9266 in a manner not

specified in this document. Product misuse can result in

a hazard. You can compromise the safety protection

built into the product if the product is damaged in any

way. If the product is damaged, return it to NI for

repair.

Hazardous Voltage This icon denotes a warning

advising you to take precautions to avoid electrical

shock.

Safety Guidelines for Hazardous Voltages

If hazardous voltages are connected to the device, take the

following precautions. A hazardous voltage is a voltage greater

than 42.4 Vpk voltage or 60 V DC to earth ground.

Caution Ensure that hazardous voltage wiring is

performed only by qualified personnel adhering to local

electrical standards.

Caution Do not mix hazardous voltage circuits and

human-accessible circuits on the same module.

Caution Ensure that devices and circuits connected to

the module are properly insulated from human contact.

NI 9266 Getting Started Guide | © National Instruments | 3

Caution When terminals are hazardous live, you must

ensure that devices and circuits connected to the

module are properly insulated from human contact. You

must use the NI 9928 backshell kit to ensure that the

terminals are not accessible.

NI 9266 with Screw Terminal Safety Voltages

Connect only voltages that are within the following limits:

AO-to-COM and

Vsup-to-COM

±36 V DC maximum

Isolation

Channel-to-channel None

Channel-to-earth ground, Vsup-to-earth ground, or

COM-to-earth ground

Continuous 250 V RMS,

Measurement Category II

Withstand up to

3,000 m

3,000 V RMS, verified by a 5 s

dielectric withstand test

Measurement Category II is for measurements performed on

circuits directly connected to the electrical distribution system.

4| ni.com | NI 9266 Getting Started Guide

This category refers to local-level electrical distribution, such as

that provided by a standard wall outlet, for example, 115 V for

U.S. or 230 V for Europe.

Caution Do not connect the NI 9266 with screw

terminal to signals or use for measurements within

Measurement Categories III or IV.

NI 9266 with DSUB Safety Voltages

Connect only voltages that are within the following limits.

AO-to-COM and

Vsup-to-COM

±36 V DC maximum

Isolation

Channel-to-channel None

NI 9266 Getting Started Guide | © National Instruments | 5

Channel-to-earth ground

Continuous 60 V DC,

Measurement Category I

Withstand up to

3,000 m

1,000 V RMS, verified by a 5 s

dielectric withstand test

Withstand up to

5,000 m

860 V RMS

Measurement Category I is for measurements performed on

circuits not directly connected to the electrical distribution system

referred to as MAINS voltage. MAINS is a hazardous live

electrical supply system that powers equipment. This category is

for measurements of voltages from specially protected secondary

circuits. Such voltage measurements include signal levels, special

equipment, limited-energy parts of equipment, circuits powered

by regulated low-voltage sources, and electronics.

Caution Do not connect the NI 9266 with DSUB to

signals or use for measurements within Measurement

Categories II, III, or IV.

Note Measurement Categories CAT I and CAT O are

equivalent. These test and measurement circuits are for

6| ni.com | NI 9266 Getting Started Guide

other circuits not intended for direct connection to the

MAINS building installations of Measurement

Categories CAT II, CAT III, or CAT IV.

Safety Guidelines for Hazardous Locations

The NI 9266 is suitable for use in Class I, Division 2, Groups A,

B, C, D, T4 hazardous locations; Class I, Zone 2, AEx nA IIC T4

Gc and Ex nA IIC T4 Gc hazardous locations; and nonhazardous

locations only. Follow these guidelines if you are installing the

NI 9266 in a potentially explosive environment. Not following

these guidelines may result in serious injury or death.

Caution Do not disconnect I/O-side wires or

connectors unless power has been switched off or the

area is known to be nonhazardous.

Caution Do not remove modules unless power has

been switched off or the area is known to be

nonhazardous.

Caution Substitution of components may impair

suitability for Class I, Division 2, or Zone 2.

Caution The system must be installed in an enclosure

certified for the intended hazardous (classified)

NI 9266 Getting Started Guide | © National Instruments | 7

location, having a tool secured cover/door, where a

minimum protection of at least IP54 is provided.

Special Conditions for Hazardous Locations Use in

Europe and Internationally

The NI 9266 has been evaluated as Ex nA IIC T4 Gc equipment

under DEMKO 12 ATEX 1202658X and is IECEx UL 14.0089X

certified. Each NI 9266 is marked II 3G and is suitable for use

in Zone 2 hazardous locations, in ambient temperatures of -40 °C

≤ Ta ≤ 70 °C. If you are using the NI 9266 in Gas Group IIC

hazardous locations, you must use the device in an NI chassis that

has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or

Ex nL IIC T4 equipment.

Caution Transient protection shall be provided that is

set at a level not exceeding 140% of the peak rated

voltage value of 85 V at the supply terminals to the

equipment.

Caution The system shall only be used in an area of

not more than Pollution Degree 2, as defined in

IEC/EN 60664-1.

8| ni.com | NI 9266 Getting Started Guide

Caution The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum

ingress protection rating of at least IP54 as defined in

IEC/EN 60079-15.

Caution The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory

requirements and limits for electromagnetic compatibility (EMC)

stated in the product specifications. These requirements and

limits provide reasonable protection against harmful interference

when the product is operated in the intended operational

electromagnetic environment.

This product is intended for use in industrial locations. However,

harmful interference may occur in some installations, when the

product is connected to a peripheral device or test object, or if the

product is used in residential or commercial areas. To minimize

interference with radio and television reception and prevent

unacceptable performance degradation, install and use this

product in strict accordance with the instructions in the product

documentation.

NI 9266 Getting Started Guide | © National Instruments | 9

Furthermore, any changes or modifications to the product not

expressly approved by National Instruments could void your

authority to operate it under your local regulatory rules.

Caution To ensure the specified EMC performance,

operate this product only with shielded cables and

accessories.

Special Conditions for Marine Applications

Some products are Lloyd’s Register (LR) Type Approved for

marine (shipboard) applications. To verify Lloyd’s Register

certification for a product, visit ni.com/certification and search

for the LR certificate, or look for the Lloyd’s Register mark on

the product.

Caution In order to meet the EMC requirements for

marine applications, install the product in a shielded

enclosure with shielded and/or filtered power and

input/output ports. In addition, take precautions when

designing, selecting, and installing measurement probes

and cables to ensure that the desired EMC performance

is attained.

10 | ni.com | NI 9266 Getting Started Guide

This manual suits for next models

Table of contents

Other National Instruments Control Unit manuals

National Instruments

National Instruments NI 9234 Manual

National Instruments

National Instruments PXIe-4322 User manual

National Instruments

National Instruments 9775 Manual

National Instruments

National Instruments Isolated Analog Output Module SCC-AO10 User manual

National Instruments

National Instruments NI 9213 User manual

National Instruments

National Instruments NI 6520 User manual

National Instruments

National Instruments SCC-A10 User manual

National Instruments

National Instruments NI 9402 User manual

National Instruments

National Instruments 9221 User manual

National Instruments

National Instruments PXIe-4302 Manual

National Instruments

National Instruments PXIe-8522 User manual

National Instruments

National Instruments SCXI-1581 User manual

National Instruments

National Instruments NI 9930 User manual

National Instruments

National Instruments Phase Matrix PXI-1430B User manual

National Instruments

National Instruments NI FlexRIO PXI-7951R User manual

National Instruments

National Instruments NI R Series User manual

National Instruments

National Instruments FIeldPoint FP-AO-200 User manual

National Instruments

National Instruments PC/104-GPIB User manual

National Instruments

National Instruments SCXI-1000 User manual

National Instruments

National Instruments FP-RLY-422 User manual

National Instruments

National Instruments FIELDPOINT FP-1600 User manual

National Instruments

National Instruments NI 9214 User manual

National Instruments

National Instruments NI PXIe-8374 User manual

National Instruments

National Instruments NI PCIe-1430 User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual