National Instruments AT-GPIB/TNT User manual

Getting Started with Your AT-GPIB/TNT and

the NI-488.2™Software for Windows

Graphics Applications

September 1994 Edition

Part Number 370880A-01

National Instruments Corporate Headquarters

6504 Bridge Point Parkway

Austin, TX 78730-5039

(512) 794-0100

Technical support fax: (800) 328-2203

(512) 794-5678

Branch Offices:

Australia (03) 879 9422, Austria (0662) 435986, Belgium 02/757.00.20,

Canada (Ontario) (519) 622-9310, Canada (Québec) (514) 694-8521,

Denmark 45 76 26 00, Finland (90) 527 2321, France (1) 48 14 24 24,

Germany 089/741 31 30, Italy 02/48301892, Japan (03) 3788-1921,

Mexico 95 800 010 0793, Netherlands 03480-33466, Norway 32-84 84 00,

Singapore 2265886, Spain (91) 640 0085, Sweden 08-730 49 70,

Switzerland 056/20 51 51, Taiwan 02 377 1200, U.K. 0635 523545

Limited Warranty

The AT-GPIB/TNT and AT-GPIB hardware are warranted against defects in materials

and workmanship for a period of two years from the date of shipment, as evidenced by

receipts or other documentation. National Instruments will, at its option, repair or replace

equipment that proves to be defective during the warranty period. This warranty includes

parts and labor.

The media on which you receive National Instruments software are warranted not to fail

to execute programming instructions, due to defects in materials and workmanship, for a

period of 90 days from date of shipment, as evidenced by receipts or other

documentation. National Instruments will, at its option, repair or replace software media

that do not execute programming instructions if National Instruments receives notice of

such defects during the warranty period. National Instruments does not warrant that the

operation of the software shall be uninterrupted or error free.

A Return Material Authorization (RMA) number must be obtained from the factory and

clearly marked on the outside of the package before any equipment will be accepted for

warranty work. National Instruments will pay the shipping costs of returning to the

owner parts which are covered by warranty.

National Instruments believes that the information in this manual is accurate. The

document has been carefully reviewed for technical accuracy. In the event that technical

or typographical errors exist, National Instruments reserves the right to make changes to

subsequent editions of this document without prior notice to holders of this edition. The

reader should consult National Instruments if errors are suspected. In no event shall

National Instruments be liable for any damages arising out of or related to this document

or the information contained in it.

EXCEPT AS SPECIFIED HEREIN, NATIONAL INSTRUMENTS MAKES NO

WARRANTIES, EXPRESS OR IMPLIED, AND SPECIFICALLY DISCLAIMS ANY

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

CUSTOMER'S RIGHT TO RECOVER DAMAGES CAUSED BY FAULT OR NEGLIGENCE

ON THE PART OF NATIONAL INSTRUMENTS SHALL BE LIMITED TO THE AMOUNT

THERETOFORE PAID BY THE CUSTOMER. NATIONAL INSTRUMENTS WILL NOT BE

LIABLE FOR DAMAGES RESULTING FROM LOSS OF DATA, PROFITS, USE OF

PRODUCTS, OR INCIDENTAL OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF

THE POSSIBILITY THEREOF. This limitation of the liability of National Instruments will

apply regardless of the form of action, whether in contract or tort, including negligence.

Any action against National Instruments must be brought within one year after the cause

of action accrues. National Instruments shall not be liable for any delay in performance

due to causes beyond its reasonable control. The warranty provided herein does not

cover damages, defects, malfunctions, or service failures caused by owner's failure to

follow the National Instruments installation, operation, or maintenance instructions;

owner's modification of the product; owner's abuse, misuse, or negligent acts; and power

failure or surges, fire, flood, accident, actions of third parties, or other events outside

reasonable control.

Under the copyright laws, this publication may not be reproduced or transmitted in any

form, electronic or mechanical, including photocopying, recording, storing in an

information retrieval system, or translating, in whole or in part, without the prior written

consent of National Instruments Corporation.

Trademarks

NAT4882®, NI-488®,Turbo488®, NI-488.2™, and TNT4882C™are trademarks of

National Instruments Corporation.

Product and company names listed are trademarks or trade names of their respective

companies.

WARNING REGARDING MEDICAL AND CLINICAL

USE OF NATIONAL INSTRUMENTS PRODUCTS

National Instruments products are not designed with components and testing intended to

ensure a level of reliability suitable for use in treatment and diagnosis of humans.

Applications of National Instruments products involving medical or clinical treatment can

create a potential for accidental injury caused by product failure, or by errors on the part

of the user or application designer. Any use or application of National Instruments

products for or involving medical or clinical treatment must be performed by properly

trained and qualified medical personnel, and all traditional medical safeguards,

equipment, and procedures that are appropriate in the particular situation to prevent

serious injury or death should always continue to be used when National Instruments

products are being used. National Instruments products are NOT intended to be a

substitute for any form of established process, procedure, or equipment used to monitor

or safeguard human health and safety in medical or clinical treatment.

FCC/DOC Radio Frequency Interference Compliance

This equipment generates and uses radio frequency energy and, if not installed and used

in strict accordance with the instructions in this manual, may cause interference to radio

and television reception. This equipment has been tested and found to comply with the

following two regulatory agencies:

Federal Communications Commission

This device complies with Part 15 of the Federal Communications Commission (FCC)

Rules for a Class B digital device. A Class B device is distinguishable from a Class A

device by the appearance of an FCC ID number located on the Class B device.

Canadian Department of Communications

This device complies with the limits for radio noise emissions from digital apparatus set

out in the Radio Interference Regulations of the Canadian Department of

Communications (DOC).

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de classe B prescrites dans le règlement sur le

brouillage radioélectrique édicté par le ministère des communications du Canada.

Instructions to Users

These regulations are designed to provide reasonable protection against harmful

interference from the equipment to radio reception in residential areas.

There is no guarantee that interference will not occur in a particular installation.

However, the chances of interference are much less if the equipment is installed and used

according to this instruction manual.

If the equipment does cause interference to radio or television reception, which can be

determined by turning the equipment on and off, one or more of the following

suggestions may reduce or eliminate the problem.

• Operate the equipment and the receiver on different branches of your AC electrical

system.

• Move the equipment away from the receiver with which it is interfering.

• Reorient or relocate the receiver’s antenna.

• Be sure that the equipment is plugged into a grounded outlet and that the grounding

has not been defeated with a cheater plug.

Notice to user: Changes or modifications not expressly approved by National

Instruments could void the user’s authority to operate the equipment

under the FCC Rules.

If necessary, consult National Instruments or an experienced radio/television technician

for additional suggestions. The following booklet prepared by the FCC may also be

helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet is

available from the U.S. Government Printing Office, Washington, DC 20402, Stock

Number 004-000-00345-4.

Bescheinigung des Herstellers/Importeurs

Hiermit wird bescheinigt, daß die AT-GPIB in Übereinstimmung mit den Bestimmungen

der Vfg. 1046/1984 funk entstört ist.

Der Detuschen Bundespost wurde das Inverkehrbringen dieses Gerätes angezeigt und die

Berechtigung zur Überprüfung der Serie auf Bestimmungen eingeräumt.

Contents

About This Manual..............................................................................................xi

Organization of This Manual.........................................................................xi

Conventions Used in This Manual.................................................................xii

Related Documentation..................................................................................xiii

Customer Communication .............................................................................xiii

Chapter 1

Introduction............................................................................................................1-1

How to Use This Manual ...............................................................................1-1

What You Need to Get Started.......................................................................1-2

Optional Equipment.......................................................................................1-2

Hardware Description ....................................................................................1-2

Software Description......................................................................................1-3

Chapter 2

Hardware Installation.........................................................................................2-1

Default Hardware Configuration....................................................................2-1

Install the Hardware.......................................................................................2-1

Note to EISA Users........................................................................................2-3

Chapter 3

Software Installation...........................................................................................3-1

NI-488.2 Software Components.....................................................................3-1

Install the Software.........................................................................................3-2

Chapter 4

Installation Verification and Troubleshooting.........................................4-1

Run the Hardware Diagnostic Test ................................................................4-1

Troubleshooting Hardware Diagnostic Test Error Messages..........4-1

Using Single-Cycle DMA.................................................4-1

Correcting Hardware Settings...........................................4-2

Run the Software Diagnostic Test .................................................................4-3

Troubleshooting Software Diagnostic Test Error Messages...........4-3

Common Questions........................................................................................4-5

Appendix A

Changing Hardware Configuration Settings............................................A-1

Selecting the Base I/O Address......................................................................A-3

Selecting the Interrupt Request Line..............................................................A-7

Note to EISA Users .........................................................................A-9

Selecting the DMA Channel ..........................................................................A-9

Note to EISA Users .........................................................................A-10

Contents

AT-GPIB/TNT for Windows Graphics viii © National Instruments Corp.

Using Programmed I/O for GPIB Transfers ..................................................A-11

Setting the Shield Ground Configuration.......................................................A-11

Appendix B

Changing Software Configuration Settings...............................................B-1

Default Software Configuration.....................................................................B-1

Note to EISA Users........................................................................................B-2

Starting and Exiting the GPIB Software Configuration Utility.....................B-2

Board Configuration.......................................................................................B-3

Expanded Board Configuration .....................................................................B-5

Device Template Configuration.....................................................................B-7

Appendix C

Hardware Specifications....................................................................................C-1

Appendix D

Customer Communication................................................................................D-1

Glossary....................................................................................................................G-1

Figures

Figure 2-1. Installing the GPIB Board...................................................................2-2

Figure 3-1. Software Installation Screen................................................................3-3

Figure A-1. AT-GPIB/TNT Parts Locator Diagram...............................................A-2

Figure A-2. AT-GPIB Parts Locator Diagram........................................................A-3

Figure A-3. Base I/O Address Switch Settings.......................................................A-6

Figure A-4. Interrupt Jumper Setting for IRQ11 (Default Setting) ........................A-8

Figure A-5. Interrupt Jumper Setting for IRQ5 ......................................................A-8

Figure A-6. Jumper Setting for Disabling Interrupts..............................................A-8

Figure A-7. DMA Channel Jumper Setting for DMA Channel 7...........................A-10

Figure A-8. DMA Jumper Setting for No DMA Channel ......................................A-11

Figure A-9. Ground Configuration Jumper Settings...............................................A-12

Figure B-1. Main Dialog Box in the GPIB Software Configuration......................B-2

Figure B-2. Board Configuration Dialog................................................................B-3

Figure B-3. Expanded Board Configuration...........................................................B-3

Figure B-4. Device Template Configuration..........................................................B-3

Contents

Tables

Table 2-1. Hardware Default Settings ..................................................................2-1

Table A-1. Possible Base I/O Address Switch Settings.........................................A-4

Table A-2. DMA Channels....................................................................................A-10

Table C-1. Electrical Characteristics of the AT-GPIB/TNT.................................C-1

Table C-2. Electrical Characteristics of the AT-GPIB..........................................C-1

Table C-3. Physical Characteristics.......................................................................C-1

Table C-4. Environmental Characteristics.............................................................C-2

About This Manual

This manual contains instructions to help you install and configure the National

Instruments AT-GPIB/TNT or AT-GPIB interface board and the NI-488.2 software for

Windows graphics applications. The NI-488.2 software is intended for use with

Windows version 3.1 or higher.

This manual uses the term AT-GPIB/TNT to refer to a National Instruments GPIB board

for the ISA (PC AT) bus equipped with the TNT4882C ASIC. The term AT-GPIB refers

to a National Instruments GPIB board for the ISA bus equipped with the NAT4882 and

Turbo488 ASICs. This manual also uses the term GPIB board in cases where the

material can apply to either board.

This manual assumes that you are already familiar with the Windows operating system.

Organization of This Manual

This manual is organized as follows:

• Chapter 1, Introduction, explains how to use this manual, lists what you need to get

started and optional equipment you can order, and briefly describes the GPIB

hardware and the NI-488.2 software.

• Chapter 2, Hardware Installation, contains instructions for installing your GPIB

board.

• Chapter 3, Software Installation, contains a description of the files on the NI-488.2

distribution disks and instructions for installing your NI-488.2 software.

• Chapter 4, Installation Verification and Troubleshooting, describes how to verify the

hardware and software installation and how to troubleshoot problems.

• Appendix A, Changing Hardware Configuration Settings, contains instructions for

changing the configuration settings of your GPIB board.

• Appendix B, Changing Software Configuration Settings, contains a description of

the GPIB software configuration utility you can use to configure the NI-488.2

software for Windows.

• Appendix C, Hardware Specifications, describes the electrical, physical, and

environmental characteristics of the GPIB board and the recommended operating

conditions.

• Appendix D, Customer Communication, contains forms you can use to request help

from National Instruments or to comment on our products and manuals.

Other manuals for AT-GPIB/TNT

This manual suits for next models

Table of contents

Other National Instruments Computer Hardware manuals

National Instruments

National Instruments PC-LPM-16/PnP User manual

National Instruments

National Instruments PXI-8335 User manual

National Instruments

National Instruments CPCI-GPIB User manual

National Instruments

National Instruments NI 6521 User manual

National Instruments

National Instruments NI 9219 User manual

National Instruments

National Instruments SCB-19 User manual

National Instruments

National Instruments MXIbus VME-AT2000 User manual

National Instruments

National Instruments Compact FieldPoint Mounting Accessories... User manual

National Instruments

National Instruments NAT7210 User manual

National Instruments

National Instruments PCI-6034E User manual

National Instruments

National Instruments NI 783 R Series User manual

National Instruments

National Instruments IMAQTM User manual

National Instruments

National Instruments NI Real-Time Hypervisor User manual

National Instruments

National Instruments DAQ PCI E Series User manual

National Instruments

National Instruments DAQ PCI-1200 User manual

National Instruments

National Instruments NI-9146 Owner's manual

National Instruments

National Instruments NI PXIe-8103 User manual

National Instruments

National Instruments PXI-6031E User manual

National Instruments

National Instruments NI PXI-8221 User manual

National Instruments

National Instruments Texas Instruments 6711 DSK User manual

National Instruments

National Instruments PXI Express PXIe-1085 Series User manual

National Instruments

National Instruments PXI User manual

National Instruments

National Instruments MXI Express x4 User manual

National Instruments

National Instruments 9260 User manual

Popular Computer Hardware manuals by other brands

EMC2

EMC2 VNX Series Hardware Information Guide

Panasonic

Panasonic DV0PM20105 Operation manual

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 user manual

Gigabyte

Gigabyte B660M DS3H AX DDR4 user manual

Raidon

Raidon iT2300 Quick installation guide

Hauppauge

Hauppauge WinTV-HVR-2250 Quick installation guide

Kontron

Kontron CP6002 user guide

Manhattan

Manhattan 702843 user manual

Aphex

Aphex 230 instruction manual

AMD

AMD Phenom II Product data sheet

Intel

Intel NUC 12 Pro user guide

dbx

dbx Zone Pro 1260 user manual

Galaxy

Galaxy GHDX2-2430S-24F4D Installation and hardware reference manual

Intel

Intel AXXRMFBU4 Quick installation user's guide

Kontron

Kontron DIMM-PC/MD product manual

ST X-NUCLEO-SAFEA1B How to use

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 installation manual

Advantech

Advantech ASMB-935 Series user manual