Nabco 710 User manual

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com

DN0011

Automatic

Entrance

Systems

NABCO ENTRANCES Inc.

S82 W18717 Gemini Drive

P.O. Box 906

Muskego, WI 53150

Phone: 877-622-2694

Fax: 888-679-3319

www.nabcoentrances.com RetrofitKit Manual

Model 710 Swing Door System

Low Energy Operator

WARNING

Do not install, operate or service this product unless you have read and understand the Safety Practices,

Warnings, Installation and Operating Instructions contained in this manual. Failure to do so may result

in property damage, or bodily injury.

Part Number 15-10677

August 23, 2004 Revision INSTALLATION MANUAL

G Y R O T E C H

Magnum Board IV.

Retrofit kit (Old Casting)

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 2 -

CAUTION:

Read these safety practices before installing, operating or servicing the automatic door. Failure to follow

these practices may result in serious consequences.

Read, study and understand the operating instructions contained in or referenced in this manual before

operating.If you do not understand the instruction, ask the installing qualified technician to teach you

how to use the door.

This manual and the owners’ manual must be given to and retained by the purchasing facility or end

user.

1. If the door appears broken or does not seem to work correctly, it should be immediately removed

from service and a qualified service technician contacted for corrective action.

2. Disconnect power at the fused disconnect during all electrical or mechanical service. When uncertain

whether power supply is disconnected, always verify using a voltmeter.

3. All electrical troubleshooting or service must be performed by qualified electrical technicians and

must comply with all applicable governing agency codes.

4. It is the responsibility of the installing door technician to install all warning and instructional labels in

accordance with ANSI A156.19.

5. It is the responsibility of the purchasing facility or end user to keep warning and instructional labels

and literature legible, intact and with the door.

6. Replacement labels and literature may be obtained from local NABCO Entrances Inc. distributors.

If the name of the local distributor is unknown, contact NABCO Entrances Inc. at (877-622-2694)

for assistance.

7. Do not place finger or uninsulated tools inside the electrical control box. Touching wires or other

parts inside the enclosure may cause electrical shock, serious injury or death.

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 3 -

Contents

Overview 4

Specifications 5

Handing Requirements 6

Hardware Kit List 7~8

Magnet Switch Assembly 9

Single Door Conversion 10

Simultaneous Pair Conversion 11

Hydraulic Closer 12

Hydraulic Closer Adjustment 13

Setting Back Check and Door Closed Switches 14~18

Simultaneous Pair Installations 19

Control Switches 19

Signage 19

Troubleshooting 20

ANSI/BHMA Specs. 21-22

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 4 -

DN0036

To The Installer The purpose of this manual is to familiarize the purchaser with the proper

installation and operation of this system. It is essential that this equipment be

properly installed and operational before the door is used by the public. It is the

purchaser’s responsibility to inspect the operation of the entrance system to be

sure it complies with any applicable standards. In the United States, ANSI

Standard 156.19 usually covers this type of door. Other local standards or codes

may apply. Use them in addition to the ANSI Standard. The GT 710 is listed

with the Underwriters Laboratory and is identified as such on the label.

Instruct the building owners/operator on the essentials of the operation of the door

and this device. The owner should follow these instructions to determine whether

the door is operating properly and should immediately call for service if there is

any malfunction.

All installation changes and adjustments must be made by qualified, NABCO

trained technicians.

Overview Earlier version of the NABCO GT710 can be retrofitted with the newer Magnum

Control Board (Magnum IV). This combination offers several control features

that accommodate most installations.

This Manual offers step-by-step instructions on how to upgrade an existing

GT710 installation with the Magnum IV and related hardware.

Figure 1 –Overview of GT710 with Magnum IV

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 5 -

Table 1 –Comparison of Magnum IV to the original GT710 Controller

Magnum IV Board GT710 Controller

Adjustable opening speed. Adjustable opening speed.

Adjustable current limit/door block

trip.

Adjustable current limit/door block

trip.

Adjustable activation timer (0 to 60

seconds)

One adjustable timer for activation and

push-n-go (0 to 60 seconds)

Adjustable separate push-n-go timer

(0 to 60 seconds)

None

Adjustable door action when detection

(continuous safety) occurs –allow

door to stop, creep open or creep

closed.

No adjustment.

Automatic shut-off of motor if door

does not open within 30 seconds.

Shut-off occurs when the timer for

activation expired.

Connection provided for swing side

mats and swing side presence detector

(Continuous safety and safety with

lockout).

N/A

Enable/disable sequential operation

via dip switch.

Enable/disable sequential operation via

onboard jumper.

Enable/disable push-n-go via dip

switch.

Wiring change required to activate

push-n-go.

Specifications Power Input 120 (±10%) AC 50-60 Hz, 5Amps

Available current for Accessories 0.5 Amps 24 Volts AC

Available Wire Size for Incoming

Power 14 AWG

Minimum Frame Face for Mounting 1¾” (44 mm)

Minimum Clearance from Top of

Door to Ceiling

7” (178 mm)

Door Hinge Requirements ¾” Butt, Offset Pivot, or Center Pivot

Door Thickness 1 ¾” (44 mm) Minimum

Door Width Specify When Ordering

Tools required 5/32”Hex Key (Allen Wrench)

Phillips Screwdriver #2

Slotted Screwdrivers, Small and Medium

Drill Bits: 11/64”and 7/8”

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 6 -

LEFT HAND

OUT-SWING

(LH)

RIGHT HAND

OUT-SWING

(RH)

LEFT HAND

IN-SWING

(LH)

RIGHT HAND

IN-SWING

(RH)

DN0015

Handing Requirements The type of door will determine whether a left-hand or a right-hand operator is

required. Figure 2can be used to determine which unit is required.

Note:

The hand of the unit and the hand of the door must be the same. The

hand of the unit is not reversible and cannot be converted in the field.

Figure 2–Determine the Swing (Hand) of the Door.

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 7 -

Hardware Kit List

This kit has been shipped with the following installation hardware.

MAGNUM IV RETRO FIT for SINGLE –P/N 11-10361-01

MAGNUM IV RETRO FIT for SIM.PAIR –P/N 11-10361-02

QtyPart #Part Description

Single Sim-

Pair

Notes

All items (#1~#24) would be packed into 8”x6”x6” box (P/N 14-1159).

1 24-9800-04 Magnum IV Control Board 1 2

2 22-10065 Main Harness -Single 1--- With Terminal Block

3 22-10270 Main Harness –Simultaneous Pair --- 1With Terminal Block

4 11-10286 Motor Harness 1 2 Four Pin Connector

5 21-9933 Power Harness -Single 1---

6 14-5883 Power Harness –Simultaneous Pair --- 1

7 11-10272 Rocker Switch Assy 1 1 No connector

8 21-9941-01 Magnetic Switch Assy - RH --- 1

9 21-9941-02 Magnetic Switch Assy - LH --- 1

10 21-10005 Magnetic Switch Plate Assy 1---

11 14-9940-01 Label for RH Operator 1---

12 14-9940-02 Label for LH Operator 1---

Use one of Labels.

13 15-10677 GT710 Retrofit Kit Manual 1 1

Packed into a 3”x4” ziplock bag (P/N 14-0828-01).

14 14-9944 Epoxy Package & Stir Stick 1 2

Packed into a 4”x6” ziplock bag (P/N 14-0828-03).

15 14-9960 Wire Saddle 3 6

16 24-1447 Wire Harness Clip 4 8

17 14-9959 Cable Clamp --- 4

18 14-9943 Ceramic Magnet 2 4

19 14-8743 Spacer for Magnum Board 4 8

20 14-1218 Wire Nut 2 4

21 14-1838 Male Pin Housing , 4 circuit 1--- For Magnetic Switch

22 24-0011-014 #10-32x1/2”Phillips Black Oxide

Screw

2 2 For Rocker Switch

23 24-4941-19 3/8-16x3/4”Hex Washer Head Screw,

2 4 For Magnetic Switch

24 24-0010-01 #10-24x7/8”Socket Head Cap Screw 4 8 For Magnum Board

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 8 -

LED

TRANSFORMER

CAPACITOR

1 2

AUX

PWR

AC IN

SW2

SW1

RELAY

R4 R5 R6 R7 R8

TDAS

SIGNAL

INPUT

TDPG LCHK CLOSE

Fuse 2: 0.5A 24 VAC

STOP OPEN BCHK

CURRENT

LIMIT MOTOR

R28

MAGNUM IV

Fuse 1: 3A 120/240

P/N 24-0010-01

Socket Head Cap Screw

#10-24x7/8"

P/N 24-4941-19

Hex Washer Head Screw, Type F

3/8-16x3/4"

P/N 24-0011-014

Phillips Head Black Oxide Screw

#10-32x1/2"

P/N 14-8743

for Magnum Board

Spacer

P/N 14-1838

4 circuit

Male Pin Housing

P/N 14-1218

Wire Nut

P/N 14-9943

Ceramic Magnet

(2)

Wire Nut

P/N 14-9944

Epoxy & Stir Stick

Epoxy and Stir Stick

P/N 24-1447

Wire Harness Clip

P/N 14-9959

Cable Clamp

P/N 14-9960

Wire Saddle

P/N 14-5883

Power Harness - Sim.Pair

P/N 11-10272

Rocker Switch Assy.

Off

Hold Open

Off

P/N 22-10065

Main Harness - Single P/N 21-9933

Power Harness - Single

P/N 11-10286

Motor Harness

P/N 24-9800-04

Magnum IV Board

P/N 22-10270

Main Harness - Sim. Pair

DN0037 Figure 3 –Installation Hardware

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 9 -

R/L

Mounting Magnetic Switch subassy

5/16-18 x 3/4" Hex Washer Head, Type F

P/N 24-4941-19

Door

Closed

Switch

Back

Check

Switch

For

RIGHT HAND

Units

For

LEFT HAND

Units

Door

Closed

Switch

Back

Check

Switch

4 2 1124 3

Magnetic Switch

Right Hand

P/N 21-9941-01

Magnetic Switch

Left Hand

P/N 21-9941-02

DN0038

Figure 4 –Magnetic Switch assembly

Model 710 Swing Door System

NABCO

ENTRANCES INC 877-622-2694 www.nabcoentrances.com - 10 -

WIRE Hrness Clip

P/N 24-1447

WIRE SADDLE

P/N 14-9960

2. Push the Clip

into the Clip.

1. Insert wires

SCREWS & SPACERS

P/N 24-4941-16 & 14-8743

MAGNUM IV BOARD

P/N 24-8900-04

MAIN HARNESS

P/N 22-10065

SINGLE DOOR CONVERSION of GT710

into the Extrusion.

DN0039

Figure 5 –Single Door Conversion of GT710

Table of contents

Other Nabco Door Opening System manuals

Nabco

Nabco Acusensor 3 User manual

Nabco

Nabco GYRO TECH GT-1175 User manual

Nabco

Nabco GT 300 User manual

Nabco

Nabco GYRO TECH GT-1175 User manual

Nabco

Nabco GYRO TECH GT-1175 Owner's manual

Nabco

Nabco GT20 Owner's manual

Nabco

Nabco GYRO TECH GT-1175 User manual

Nabco

Nabco GT20 User manual

Nabco

Nabco ICU 2400 User manual

Nabco

Nabco GT20 8300 User manual

Nabco

Nabco 243681-05 User manual

Nabco

Nabco GT20 Owner's manual

Nabco

Nabco GT-710 User manual

Nabco

Nabco Opus Control User manual

Nabco

Nabco GT-1400 User manual

Nabco

Nabco C-00139 User manual

Popular Door Opening System manuals by other brands

Pamex

Pamex KT-INP35 Installation instruction

Label

Label NEPTIS/LE installation manual

Cal-Royal

Cal-Royal N-F77CVR Installation instruction

Scrigno

Scrigno OPEN1000 Assembly manual

TriMark

TriMark UM 34 instructions

BFT

BFT WIND RMB 130B 200 installation manual

Alecto

Alecto ADI-250 user manual

Besam

Besam Swingmaster MP Installation, adjustment and maintenance instructions

CRL

CRL SENIOR PRIMA manual

Assa Abloy

Assa Abloy SARGENT 1431 Series instructions

GAL

GAL MOVFR Quick setup

Olide

Olide 120B installation manual

Normstahl

Normstahl IDO7 installation manual

Häfele

Häfele Finetta T 70 VF manual

AGS

AGS D-PL Instructions for fitting, operating and maintenance

Stanley

Stanley MA900ñ Installation and owner's manual

WITTUR

WITTUR Hydra Plus UD300 Instruction handbook

Alutech

Alutech TR-3019-230E-ICU Assembly and operation manual