MXN MXN-HD8DVRQ User manual
8" Digital Video Recorder for Car
Instruction Manual(Ver. 1.0)
Thank you for purchasing our DVR for car. Please read this manual before
you use the product. The product may be different from the described in
the manual depending on renewal and/or upgrade of S/W version and
performance and it can be altered without notice.
Index
1. Caution
2. Components of the product
3. How to use the product
4. How to install the product
5. How to use PC Player
6. Specification
4ch.
MXN-HD8DVRQ
IP67
Water
Proof
Caution
For your safe operation, please read this manual before you start to use the product.
We inform you that our company shall not be responsible for failures and troubles
that are occurred due to misuse or neglection of the cautions written on this manual.
Operating this equipment when driving a car might cause an accident. Use the
equipment after parking or stopping the car in a safe area.
When wiping off the dust, use a soft fabric instead of liquid solvents (thinner,
benzene etc.) solution or a wet rag.
Do not press the liquid crystal screen hard. It might be damaged by hard pressure.
Do not drop or give shock. It might cause breakdown or damage.
Do not dismantle the product arbitrarily. We do not supply free after service for
an arbitrarily dismantled product.
Touching the power with a wet hand causes electric shock. Caution required.
For accessories or cables to connect with the product, it is recommended to
use honest goods from our company. We are not responsible for any problems
caused by fraudulent articles.
Do not disconnect the power cable during using the product. It might cause
damage to the product.
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Modifications not expressly approved by the manufacturer could void the user's
authority to operated the equipment under FCC rules.
FCC (Federal Communications Commission)
1
Caution
SD Card
Do not pull out the SD card during playing or recording process.
Use proper type SD card: it should be higher than Class 10 level SD card.
Recommended brands of SD card: Sandisk, Transcend or Samsung.
Please check the mark as "Class10 & Full-HD" on the package before you
purchase SD card.
Removal Magnet
There is a magnet in the monitor's backside to prevent discharge of the internal
back-up battery.
This magnet needs to be removed before first time use of model MXN-HD8DVRQ.
Unscrew the bolt in the monitor's backside by L-wrench and then remove the magnet
under the bolt.
After removing the magnet, the built-in back-up battery is activated.
Back-up Battery Recharge
The back-up battery can be recharged when the ACC is on (Drive Mode).
(If the ACC if off, it is not recharged for protection of the car battery.)
When it is fully charged, recharging is automatically stopped.
It takes about 5 or more hours to fully charge the battery.(Recharging time may be
different depending on temperature and circumstances.)
It may take longer to charge batteries unused for a long time.
The voltage of the back-up battery can be checked on [Battery Voltage] menu.
(See: Battery Voltage, Page 27.)
Caution : This part informs what to keep in mind or understand and
what caution is required to use the product.
Ref (reference) : Reference is about functional explanation
Amplified explanation is as follows.
2
Components of the product
1112
1
2
3
4
5 6 7 8
9
10
15
14
1
2
3
4
5
6
7
8
Remo-con Receiving Window
Recording Display LED
Recording START/STOP Button
Event Recording Button
Screen ON/OFF Button
Channel Switch Button
Menu ON/OFF Button
Power ON/OFF Button
9
10
11
12
13
14
15
illuminance Sensor
SD Card Cover and Lock
Power Cable (Blue Cable)
Camera Cable (Black Cable)
Touch Screen
SD Card Slot (4 slots)
Reset Button
3
7
System Connection
1
2
3
4
5
6
7
8
VIDEO IN/OUT
EXT. GPS Module
AUDIO IN/OUT
5
4
3
2
1
6
8
AUDIO in
DC 12VVIDEO in
NC
(Optional : Heater/Shutter)
GROUND
Camera connection
Camera Cable
Blue
Black
Blue
Black
Black
Yellow
Red
Power Cable
Camera 1
Camera 2
Camera 3
Camera 4
Camera 5
NO. Wire Color Label
GRAY Trigger 3 ( 9 ~ 30V DC, via direction light, etc. )
BLUE Trigger 4 ( 9 ~ 30V DC, via direction light, etc. )
GREEN Trigger 2 ( 9 ~ 30V DC, via direction light, etc. )
ORANGE Trigger 1 ( 9 ~ 30V DC, via direction light, etc. )
BROWN ACC Power ( 12 ~ 36V DC, via ignition )
WHITE Speed Pulse (via tachograph, 10 ~ 200 Hz )
RED B+ Power (12 ~ 36V DC, via Battery )
BLACK Ground
AUDIO in
DC 12V VIDEO in
NC
(Optional : Heater/Shutter)
GROUND
Monitor connection
Components of the product
4
Components of the product
SD Card Cover & Lock
The SD card cover protects SD card on the top of the device.
SD Card Cover is locked up and you can use only the enclosed key to open and
close it.
When removing the card, push the end of it with a finger tip. Then it is unlocked and
comes out. If the card is pushed too hard it might popped out toward your face.
Please push it gently.
How to use SD Card
There are total 4 slots for the SD card.
For each slot, it is possible to equip a SD card (separate purchase) with up to 32 GB
capacity. (total capacity of 128GB)
How to insert/remove card: Pay attention not to confused with the front and the back
sides of the card before inserting it and push the card into the slop entirely.
Reset
When there is an error or malfunction in the operation of the product please
press the reset button.
Reset button is located in the hole between No.1 and No.3 SD cards under
the SD card cover on the top of this product.
Caution:
Please make it sure that the front side of the card is up. When the card is inserted
in a wrong way, there might be break down or the card wouldn't come out.
Caution:
The SD card might not be recognized depending on manufacturer and memory.
5
Components of the product
Touch Screen
How to use Touch Screen:
It is also possible to control or set functions of the equipment by touching the screen.
For full instructions about the touch screen function, please see [How to use the
product] in the manual.(See: How to use the product, Page 12.)
Touching the small screen of each channel at the multi-screen mode brings a full
screen for the channel.
6
Components of the product
Manual Operation of Record Button(Manual Recording)
Event Recording Button (Emergent Recording)
E.save button can be used for emergency recording at the moment. (Unlike REC
button, it also records former 15 seconds before pressing the button.)
E.save Recording Time
1) Unless normal recording is on, it helps to record total 30 seconds more of
15 seconds each before and after the operation.
2) During normal recording, it is possible to record by using Event Rec. Time Set.
function.(See: Event Rec. Time Set, Page 19.)
Note:
Constant recording (recording by REC button click, by Power On Auto Rec
setting)refers to recording at the drive mode.(See: Power On Auto Rec, Page18.)
During record, red LED on the left side of REC button is on.
It is not possible to stop it manually and it is automatically stopped when
recording is done.
When recording is finished LED also goes off.
Recorded files are stored in Event folder of Player.
When REC button is clicked, all channels are recorded.
During record, red LED on the left side of REC button is on.
One more click ceases recording and LED will be off.
Recorded files are stored in Normal folder of Player.
Recording Display LED
Recording Start/Stop Button
Event Recording Button
7
Components of the product
LCD Button (Screen ON/OFF)
Screen Switch (by Channel) Button
Channel moves in order as below when pressing the button.
( CAM1-CAM2-CAM3-CAM4-SPLIT1-SPLIT2-SPLIT3-NORMAL-CAM1... )
When LCD button is clicked, the screen is turned off.
When the button is clicked again, the screen is turned on.
The LCD is turned off automatically by setting Screen On Time
(See: Screen On Time, Page 21.)
Screen ON/OFF Button
Screen Switch (by Channel) Button
Main Menu Button (Menu Open/Close)
When you click [M] button on the front, six main buttons will be displayed on the
screen.(See: Main Menu Start, Page 13.)
If you click it again, Main Menu will be disappeared.
You can have Main Menu closed automatically by setting Menu Display Time.
(See: Menu Display Time, Page 13.)
Main Menu Button
8
Components of the product
Power ON/OFF
illuminance sensor
This window is to setup sensor that detects brightness of the exterior of the car.
Set up Dimmer on Configuration to control brightness of the screen as you want.
(See: Dimmer, Page 22.)
Caution :
When turning the Power button on or off, it is not changed to the Parking mode.
Use the ACC On/Off button of the car if you want to have the Parking mode.
When you click the Power button, the device is turned on and starts booting.
When turning On/Off the power with Power button, it is not changed to the parking
mode.
Clicking the button at the parking mode turns on the screen and the mode will be
changed to the drive mode.
When you click the button when the power is on a pop-up window will be displayed
to ask whether to close the power or not. [Cancel] button helps to cancel closing
and [Yes] buttons closes the power.
Power ON/OFF Button
illuminance Sensor
9
Table of contents
