MTX RZRXP-10 User manual

MTX.COM

OWNER’S MANUAL

RZRXP-10

POLARIS®RZR®AMPLIFIED SUBWOOFER ENCLOSURE

MTX.COM

IMPORTANT NOTICE

If you have any questions regarding wire routing in a vehicle, please contact MTX Technical Support

at 1-800-225-5689.

When connecting power and ground wires ensure that the red power wire is fused at the point

where it is connected to the vehicle’s battery. Failure to do so can result in damage to the vehicle if a

short circuit develops between the vehicle connection point and the product.

PRODUCT INFORMATION

Model #

Serial #

Dealer’s Name

Date of Purchase

IN THE BOX

• RZRXP-10AmpliedSubwooferEnclosure

• EBCandEBCExtensionWire

• Mounting Hardware

  (1)1"T30TorxScrew

  (2)1.5"T30TorxScrews

ADDITIONAL ACCESSORIES NEEDED AND NOT INCLUDED

MTX recommends using StreetWires PS1K-10 amp kit which includes the following:

• PowerandGroundWiretoRuntotheBattery

• 20AATCFuseHolderandFuse

• AccessoryConnectionWire

• RCACablestoConnecttotheSource

INSTALLATION TOOLS

The following is a list of suggested tools needed for installation:

• Torx-T40

• Torx-T30

• Torx-T25

• 10mm Wrench or Socket

• Razor Knife

INTRODUCTION

ThankyouforpurchasingtheMTXAudioampliedsubwooferenclosuredesignedforthePolaris®

RZR®.TheeasytoinstallsubwooferistheperfectdirecttbasssolutionforyourPolaris®RZR®.

CongratulationsandenjoytheultimateaudioexperiencewithMTX!

FITS THE FOLLOWING VEHICLES

• RZR®XP/XP41000(2014andUp)

• RZR®XP/XP4TURBO(2016andUp)

• RZR®900/900S/1000S(2015andUp)

• RZR®4900EPS(2015andUp)

NOTE:Willnottonvehicleswiththeaddedheateraccessory.

MTX.COM 3

FEATURES

• 10"All-WeatherAmpliedSubwooferEnclosure

• Integrated250-WattRMS/500-WattPeakPowerAmplier

• IntegratedPowerandGroundConnections

• LowLevelInputwithExternalGainControl

• DashMountBassControlKnob(Included)

• MountsUnderneathDashboard-DirectFit,NoDrillingRequired

SPECIFICATIONS

• RMS Power Handling: 250-Watts

• Peak Power Handling: 500-Watts

• FrequencyResponse:34Hz-120Hz

MTX.COM

INSTALLATION

Step 1 - Release the two quick locks to remove the hood from the vehicle.

Step 2 - Lift up the hood and slide towards the front of the vehicle.

Step3-Removethetwo(2)T40screwsholdingdownthetopdashcover.

MTX.COM 5

Step4-Liftandpullbackthetopdashcovertoreleasetheclipsholdingitinplace.Unplugthegauge

and switches making sure not to damage the vehicle and ignition wiring. Make note to remember

whatconnectorisassociatedwitheachspecicswitch.

Step5-RemovetheTorxheadscrewfromthedashpocketbrace.Afterthisisremovedtheplastic

dash pocket and bracket can be pulled out of the dash.

MTX.COM

Step6-Removethetwo(2)T40screwsholdingthedashboardinplace.

Step 7 - Pull the dashboard towards the back of the vehicle. There are locking clips on the right and

left side that hold it in place. The dash will pop out.

MTX.COM 7

Step 8 - Carefullylift the dash out of the vehicle. If the locking clips have fallen off, place them back

onto the locking tabs on the dash. These are needed to re-assemble the dashboard.

Step9-Removethetwo(2)10mmhexboltsthatareholdingthegloveboxtothevehicleframe.When

thescrewsareremovedthegloveboxcanbelowereddownandoutoftheenclosure.

Step10-Removetheve(5)T25screwsholdingthegloveboxtogether.Thegloveboxwillthenopen

like a book.

MTX.COM

Step11-Cutthe“binding”plastichingewitharazorknifetoseparatethefrontandbackoftheglove

box.Thebacksideofthegloveboxwillnolongerbeused.Thefrontsideofthegloveboxwillbe

attached to the enclosure.

Step12-Usingtheve(5)T25screwsthatwereremovedfromthefront/backassemblyoftheglove

box,attachthefrontofthegloveboxtotheRZRXP-10enclosure.Takecaretonotstripouttheplastic,

buttightenitenoughsothegasketsealsbetweentheenclosureandglovebox.

Step 13 - The enclosure can now be placed into the vehicle. Place the rectangular protrusion at an

angleintothedasharearst.Theenclosurecantheneasilyslideupintoplace.

MTX.COM 9

Step14-Holdtheenclosureupandalignthegloveboxscrewholeswiththevehicleframemount.

Replacethetwo(2)10mmhexboltsandtightentheenclosureinplace.Itmayhelptoplacea

supportingobjectundertheenclosuresobothhandsarefreetolineupthescrewholeswiththe

vehicle frame mount.

Step 15 - There are three mounting holes on the bottom of the enclosure to screw the base of

the enclosure into place. The furthest hole to the right uses the included 1" screw. The other two

mounting holes use the 1.5" screws. Tighten the screws down, but take care to not strip them. These

screws lock into the plastic foot board.

MTX.COM

Step 16 - Now that the enclosure is securely tightened in place, the power and signal wires need to

be connected to the battery and signal source.

• The Red wire should be connected directly to the battery’s positive terminal and fused with a

20A fuse.

• The Blackwireshouldbedirectlyconnectedtothebattery’snegativeterminal.

• If your vehicle is equipped with the Polaris®bussbarkit,theRedandBlackwirescanbe

  connectedtothebussbarunderthehoodontherewall.TheRedwirewillstillneedtobe 

fused.

• The BluewirecanbeconnectedtotheACC/KeyTurnOnlocatedonthebussbarofanyvehicle.

Step17-ConnecttheRCAinputstothesignalsourceofyourchoice

Step 18 - Turn the unit on and check to make sure everything works. Set the gain using the gain pot

that is attached to the orange / grey wires. Set the gain to the bass level desired.

Step19-TheincludedEBCcanbeconnectedandmountedtoadesiredlocationtoalloweasytrim

adjustmentofthebasslevelafterthegainhasbeenset.

Step 20 - Replace all the parts and screws that have been removed to return the RZR back to its

completely assembled state.

Table of contents

Other MTX Subwoofer manuals

Popular Subwoofer manuals by other brands

Sony

Sony XS-AW8 operating instructions

Sony

Sony XS-L836 Specifications

B&C Speakers

B&C Speakers 15 HPL 76W Specifications

Velodyne

Velodyne DD-18+ Specifications

Sonance

Sonance Cinema Series SUB 10-150 Specifications

Hifonics

Hifonics HW-12 Owners & installation manual

Magnat Audio

Magnat Audio ADR 130 BP user manual

Blitz

Blitz BZP106 Specifications

Technics

Technics SB-AS500 Operaing instructions

Lyngdorf

Lyngdorf BW-2 owner's manual

Lyngdorf

Lyngdorf BW-3 owner's manual

Pyle Pro

Pyle Pro PYLE PRO PDW15125 owner's manual

REL Acoustics

REL Acoustics Q Series operating instructions

Pioneer

Pioneer Elite S-W1EX Service manual

L-Acoustics

L-Acoustics KIVA SB15M Rigging manual

B&C Speakers

B&C Speakers Woofer 12 HPL 76 specification

KEF

KEF KUBE 200 installation manual

Yamaha

Yamaha SW500 owner's manual