MTD 390-674-000 Installation instructions

SNOWTHROWER

SNOW CAB

Model #390-674-000

PARTS LIST / ASSEMBLY / OPERATION

! IMPORTANT !

READ THIS ASSEMBLY MANUAL CAREFULLY AND KEEP FOR FUTURE REFERENCE

REMOVE THE VINYL COVER BEFORE TRANSPORTING THE SNOW BLOWER IN AN OPEN

TRUCK OR TRAILER.

9550704 1

WARNING

1. This cab is designed to provide foul weather protection only. It does not provide protection from

noise, exhaust fumes, chemicals or injury from collision, rollover or other accidents.

2. Do not operate machine in confined areas without proper ventilation.

3. Thoroughly check area of operation before using machine.

4. The cab adds height to the machine. Low tree limbs and other overhead structures that did not

interfere with the operation of the machine before, may now be obstacles.

MAINTENANCE INSTRUCTIONS

A. Periodically check all bolts to see that they are tight. If bolts become loose, failure of cab parts

may occur.

DO NOT CLEAN THE CLEAR PLASTIC WINDOWS WHEN THE PLASTIC IS DRY.

THE CLEAR PLASTIC WILL SCRATCH.

B. Avoid contact with plastic windows. Keep plastic windows clean by washing them with clear

running water and rubbing with your bare hands, only. The use of a rag, sponge or brush will

scratch the plastic. Liquid soap may also be used for window cleaning. During freezing weather,

an automotive windshield washer solvent may be used.

C. Use liquid soap and water to clean colored vinyl portions. Scrubbing with a brush or rag is also

permitted on the colored vinyl portions.

STORAGE INSTRUCTIONS

Prior to storage clean the windows and colored vinyl parts with a mild automotive detergent, rinse

with clean water and allow to thoroughly dry, Store cab in a clean dry place out of direct sunlight.

Avoid folding plastic windows.

SNOWTHROWER SNOWCAB MODEL #390-674-000

CARTON CONTENTS

KEY # PART # QTY DESCRIPTION

1 9546 1 BRACKET, RH

2 9547 1 BRACKET, LH

3 4977 2 POST, FRONT

4 2389 1 HORIZONTAL CURVED BOW

5 4968 1 REAR VERTICAL BOW

6 2230 1 TOP FRAME

7 9354-B 1 VINYL COVER

8 9234 4 1” “U” Clamp

9 2236 2 1 1/4” “U” Clamp

9548 1 HARDWARE PACKAGE (Contents Listed Below)

0788 6 1/4”-20 X 3/4” Cap Screw

0926 2 1/4” –20 X 1” Cap Screw

6653 2 1/4”-20 X 2” Cap Screw

4556 4 1/4” Fender Washer

0730 10 1/4”-20 Two Way Locknut

1175 4 5/16”-18 x 1 3/4” Cap Screw

0729 4 5/16” Two Way Locknut

7929 2 Caplug

STEP 1; SEE FIGURE 1:

Use figure one to identify all of the steel frame parts.

Figure 1

INSTALLATION INSTRUCTIONS

READ THESE INSTRUCTIONS COMPLETELY BEFORE INSTALLATION.

The right side of the cab is determined from the operator’s position.

NOTE: Match your snowblower handlebar to the

illustration and follow the corresponding

instructions

STEP 2; SEE FIGURE 2:

Install Brackets, Left and Right (1&2)

For 2004 & up Models

A. Remove the bolt at Reference A. Place the

right Bracket onto the side of the handlebar and

replace the bolt. Do not tighten at this time.

B. Place the 1” U Clamp over the handlebar open

end forward. Insert a 5/16” x 1 3/4” bolt inwards

through the clamp. Place the lower hole of the

Bracket over the bolt on the inside of the

handlebar. Add a nut. Do not tighten at this time.

STEP 2; SEE FIGURE 3:

Install Brackets, Left and Right (1&2)

For 1990 to 2003 models

A. Attach bottom end of Bracket with a 1” U

Clamp and 5/16” x 1 3/4” bolt and locknut.

Keep U Clamp open end up with Bracket on the

outside. Do not tighten at this time.

B. Remove the carriage bolt at Reference M.

Insert a 5/16” x 1 3/4” bolt through the Bracket

and then the handlebar. Add a 5/16” locknut. Do

not tighten at this time.

Figure 2 2004 & up Models

FIGURE 3 1990 to 2003 models

! WARNING!

Make sure that the installed brackets

do not interfere with the operator

controls.

STEP 2; SEE FIGURE 4:

Install Brackets, Left and Right (1&2)

For 1990 to 2003 Economy Models

A. Remove the bolts at Reference N. Drill the

hole out to 5/16”.

B. Insert a 5/16” x 1 3/4” bolt inwards through

the lower hole in the Bracket and then the

handlebar. Add a locknut do not tighten at this

time.

C. Remove the carriage bolt at Reference P.

Insert a 5/16” x 1 3/4” bolt through the Bracket

and handlebar. Add a locknut. Do not tighten

at this time.

STEP 2; SEE FIGURE 5:

Install Brackets, Left and Right (1&2)

For 1985 to 1990 Models

A. Remove the carriage bolts at Reference Q.

Insert a 5/16” x 1 3/4” bolt through the Bracket

and handlebar. Add a locknut. Do not tighten

at this time.

B. Place the 1 1/4” U Clamp over the

handlebar open end forward. Insert a 5/16” x 1

3/4” bolt inwards through the clamp. Place the

lower hole of the Bracket over the bolt on the

inside of the handlebar. Add a nut. Do not

tighten at this time.

STEP 2; SEE FIGURE 6:

Install Brackets, Left and Right (1&2)

For Pre 1985 Models

A. Place the 1” U clamps against the top of the

control panel open end up. Insert 5/16” x 1

3/4” bolts inwards. Add locknuts. Do not

tighten at this time.

B. Place the 1” U Clamps open end pointed

down over the handlebar. Insert 5/16” x 1 3/4”

bolts inwards. Add locknuts. Do not tighten at

this time.

Figure 4 1990 to 2003 Economy Models

FIGURE 5 1985 to 1990 Models

FIGURE 6 Pre 1985 Models

STEP 3; SEE FIGURE 7:

A. Attach the Horizontal Bow (4) and the Front Posts (3) to the Brackets (1 & 2) using two 1/4" x 3/4"

bolts and locknuts (refer to detail A).

B. Position the Front Posts on the inside of the assembly, the mounting tabs on the Horizontal Bow in

the middle and the Brackets on the outside.

C. Be sure the tops on the Front Posts point toward each other.

D. Keep the bolt heads on the exterior of the enclosure. Do not tighten the bolts at this time

STEP 4; SEE FIGURE 7:

A. Mount each leg of the Rear Vertical Bow (5) to the Brackets and the Horizontal Bow using a 1/4 x

1" bolt, two 1/4" fender washers, and a locknut (refer to detail B).

B. Be sure that the tabs on the Rear Vertical Bow are towards the front of the cab.

C. Position the bolt on the inside of the cab, with a fender washer on each side of the framework.

D. Position the Bracket on the inside of the assembly, with the Rear Vertical Bow in the

middle, and the Horizontal Bow on the outside. Do not tighten bolts at this time.

STEP 5; SEE FIGURE 7:

A. Attach the Top Frame (6) to the Rear Vertical Bow and the Front Posts using four 1/4" x 3/4" bolts

and locknuts.

B. Keep the bolt heads on the exterior of the frame.

C. Position the Rear Vertical Bow on the inside of the Top Frame.

D. Tighten all the bolts making sure that the Rear Vertical Bow (5) is at a 90-DEGREE angle to the

Horizontal Bow (4).

NOTE: This angle is critical so that the vinyl cover fits properly.

Figure 7

STEP 6; SEE FIGURE 8:

Install the Vinyl Cover (7) over the framework.

A. Place the Vinyl Cover over the frame and secure all of the snaps.

B. Place a caplug over the exposed threads of the 1" bolt on both sides at Reference C.

MTD customer service 1-800-800-7310

Figure 8

Table of contents

Other MTD Snow Blower Accessories manuals

MTD

MTD 19A30022100 User manual

Popular Snow Blower Accessories manuals by other brands

EGO

EGO SSA1200 Operator's manual

LANDY

LANDY S-SPE Operator's manual

Bercomac

Bercomac 700525-2 instructions

Boss Snowplow

Boss Snowplow MSC23000 owner's manual

Briggs & Stratton

Briggs & Stratton 1696092-00 Operator's manual

Cub Cadet

Cub Cadet 190-401-100 owner's manual

Polaris

Polaris 2882798 manual

Meyer

Meyer CP7.5 Parts & Installation Instructions

PRONAR

PRONAR PUV-3600HD Operator's manual

Boss Snowplow

Boss Snowplow SNR24024 owner's manual

Husqvarna

Husqvarna ARST5120Xv1 manual

Blizzard

Blizzard POWER PLOW 810SS Installation instructions & owner's manual

LOFTNESS

LOFTNESS 481EFT Operator's manual / parts book

Rotary

Rotary SlushPlow quick start guide

Western

Western MVP installation instructions

Meyer

Meyer Lot Pro LP-7.5 Parts & Installation Instructions

Boss Snowplow

Boss Snowplow BRX25175 owner's manual

Motoalliance

Motoalliance DENALI manual