MPK 28 Manual
1
Fitting and Operating Instructions
GB
Rooight Model 28, 32, 40
Issue Nov. 2013 We reserve the right to change technical
specications without notice. E&OE
ISO 9001:2008
Cert.-No. 01 100 89747
ISO 14001:2004
Cert.-No. 01 104 069609
Metall- und Plastikverarbeitungs- GmbH & Co. KG Kierspe
Internet: www.mpk-kierspe.de
2
We only recommend installation by authorised dealers.
Please read these instructions carefully before tting and operating the
rooights.
Important: We cannot be held responsible for incorrect tting, handling or
operation.
Any product faults relating to the production and materials used should be
notied to us via an authorised dealer immediately.
Illustration
1 2 3
4 5 6
7 8
wrong
wrong
wrong wrong
wrong
3
Fitting Instructions
Warning!
Fitting position
Aperture size
Roof thickness
Fitting direction
Fitting screws
Sealing
Fitting
Never stand on the dome of the rooight!
(See picture 1)
Choose a tting position that will not interfere with other roof
mounted components (e.g. roof-racks/antenna's etc.) and avoid
internally installed electrical cables and furniture, which could
impede the correct operation of the rooight.
The rooight should only be tted to a at roof surface, both in-
ternally and externally.
Depending on rooight model (see technical data page 6 - 7).
Ensure the correct rooight is selected for the roof thickness (for
available size options see page 6).
Rooights must only be tted with the operating handles facing
the front and rear of the vehicle, not across the vehicle.
The length of the screw should be determined by the roof thick-
ness, plus approximately 10 mm tor the screw to enter the upper
frame.
Secure only with pan, or round headed screws (not supplied), 3,5
mm/ head according to DIN ISO 7049 (DIN 7981). Do not
use
countersunk screws as they will damage the rooight frame.
(See picture 4).
Use only long term exible sealant, suitable for external use, (not
supplied), and also suitable for the material of the upper frame.
Consult your sealant supplier.
Before tting the rooight remove the proles covering the ynet
and blind rollers. These are temporarily/partially tted into place
when new. PLEASE NOTE: When fully tted these proles cannot
be removed without being damaged. It is therefore important to
make sure the rooight is tted and operates correctly, before fully
installing the proles.
Correctly align the upper and lower frames and secure evenly with
the screws. Do not over-tighten as this may damage the frame, or
affect the correct operation of the rooight. If the inner frame starts
to distort, the correct torque has been reached (See picture 2-3).
Screws not supplied!
4
Operation Instruction
Instruction for use
Free-air-ow
Before driving
Cleaning
The rooight can be opened fully, or in four different directions, so
that the dome can be angled against driving weather conditions. To
open squeeze the locks (optional) into the handles and push open.
To open and close pull the ynet slightly into inner direction until
it slides beside the ynet click. Do not open more than 90°, to
avoid damaging the hinges. Do not over-bend as this may break
the ynet frame.
When closed there is a free airow through the rooight, which must
be kept free at all times (see technical data page 6-7).
Never close the openings of the free-air-ow.
IMPORTANT: All rooights must be closed and locked down before
travelling. (See picture 5-6)
Care Instructions
The rooight should only be washed by hand, using a sponge with
plenty of clean water to avoid scratching. Caustic detergents and
solvents may attack the plastic and make it brittle or disintegrate.
For easier cleaning of the dome it can be removed from the frame
by releasing the four screws holding the handle arms. (Models from
May 2010, Trox TK10 screws) (See picture 7)
Make sure that only the original screws are used when replacing
the dome and that they enter the thread in the plastic correctly. Do
not over-tighten
Never remove the screws holding the dome and the handles to-
gether (See picture 8). These are secured by a torque screwdriver
and should only be handled by an approved dealer.
Remove the ynet. The ynet is hanged in and it is removed by
rst opening fully and hanging out from the frame. Reverse the
process to install.
Attention: To avoid damage, do not bend the ynet frame. Clean
the ynet mesh only with clean water too.
5
Technical Data:
Dome/ outer frame material: Polypropylene
Model 28
Aperture: 280 x 280 mm
Size dome: 330 x 330 mm
Free-air-ow: 60 cm²
Height over roof: 78 mm
Model 32
Aperture: 320 x 360 mm
Size dome: 380 x 420 mm
Free-air-ow: 120 cm²
Height over roof: 83 mm
Model 40
Aperture: 400 x 400 mm
Size dome: 480 x 480 mm
Free-air-ow: 30 cm² / 150 cm²
Height over roof: 91 mm
Product description
- Opaque rooight with free airow
- Spring assisted mechanism, ipable into four different directions, with locks
- Concealed xing screws
- Removable ynet, optional roller blind
- ECE R43 Whole Vehicle Type Approved
(Please ask for further details.)
Technical Information
6
Technical Information
Model Options:
Model 28
Not available anymore, has been replaced by rooight model 29.
Model 32
white grey beige roller net roof thickness air-ow weight
--- --- 320VB --- --- 24-46 mm 120 cm² 1350 g.
--- --- 320VNB --- X 24-46 mm 120 cm² 1400 g.
Model 40
white grey beige roller net roof thickness air-ow weight
400VAW --- 400VB --- --- 24-46 mm 150 cm² 1700 g.
400VNAW --- 400VNB --- X 24-46 mm 150 cm² 1750 g.
--- --- 401VB --- --- 32-55 mm 150 cm² 1780 g.
--- --- 401VNB --- X 32-55 mm 150 cm² 1830 g.
--- --- 403VB --- --- 56-89 mm 150 cm² 1850 g.
--- --- 403VNB --- X 56-89 mm 150 cm² 1900 g.
7
1
2
3
5
6
4
Spare parts
Colour frame:
Nr. Spare parts beige white grey
1a Replacement dome model 28 290.52VB 290.52VAW 290.52VG
1b Replacement dome model 32 320.52VB ---------- ----------
1c Replacement dome model 40
150 cm³ air-ow 420.52VB 420.52VAW 420.52VG
2a Outer frame model 28 280.22B 280.22AW 280.22G
2b Outer frame model 32 320.22B ---------- ----------
2c Outer frame model 40/401 400.21B 400.21AW 400.21G
Outer frame model 403 400.23B ---------- ----------
3a Inner frame model 28 280.21B 280.21AW 280.21G
3b Inner frame model 32 320.21B ---------- ----------
3c Inner frame model 40 400.22B 400.22AW 400.22G
Inner frame model 401/403 401.22B ---------- ----------
4 Handle for replacement-roller 450.3B ---------- ----------
5 Locks: 1 set supplied in polybag
with hanger, single packed
For rooight model 28 270.99S 270.99S 270.99S
For rooight models 32,40-403 420.99S 420.99S 420.99S
6 Screws for handles 8000.4 8000.4 8000.4
This manual suits for next models
2
Table of contents
Other MPK Lighting Equipment manuals
Popular Lighting Equipment manuals by other brands
Qazqa
Qazqa Suplux SL 3 Black 103062 instruction manual
Commercial Electric
Commercial Electric 54568141 Use and care guide
CREE LIGHTING
CREE LIGHTING 304 Series installation instructions
Goobay
Goobay 49867 user manual
ECOMAN ITALIA
ECOMAN ITALIA LED T8 instruction manual
Alkalite
Alkalite Krypton KT-81 user manual
