1.0
Before assembling the ladder, please study the following safety instructions carefully.
• Please read the assembly instructions carefully.
• Decide on a place for climbing into and out of the pool. Adjust the length of the initial step accordingly.
• The ladder must stand on a solid and smooth surface so that it is stable.
• The ladder must not be used by more than one person at a time. THE LADDER’S LOAD BEARING CAPACITY IS 100 Kg.
• When climbing up and down the ladder, face towards the steps and do not sway or swing from them.
• Do not dive directly from the ladder or jump into the pool from it.
• Never swim underneath the ladder or into the space between the ladder and the wall of the pool. This could lead to a risk of drowning.
• For safety reasons, if you are not using the ladder, remove it from the pool. Never leave it within reach of children.
• Inspect all parts of the ladder before use.
• Do not use the ladder for any other purpose than that which it is designed for.
• When you are not using the pool, we recommend that you clean and dry the ladder, and store it out of reach of children.
• Persons with reduced mobility and small children are only permitted to use the ladder when accompanied (assisted) by physically and mentally capable persons.
STEP 1:ASSEMBLE THE HANDRAILS AND THE PLATFORM
Slidethe ladder’shandrails(4)into theholes inthe platform(1)from above. (fig.1)Then,slide the
parts which will serve as the support for the ladder on the outside of the pool onto the handrails
from below. For a pool with a depth of 120 cm in relation to the ground, use the nipple (8) and
for a pool with a depth of 110 cm in relation to the ground, use the curved feet (6 and 7). When
assembling,thecurved feetmust faceawayfromone anotherand thescrewholes forthe braces(9)
must be parallel to the plane of the platform (1). Make sure that the holes in the handrails (4) are
alignedwith theholes inthe platform(1) andin thenipples (8)(curvedfeet (6and 7)).Screwthem
togetherusing 2screws(11) andclosed nuts(12). Insert thescrews fromtheoutside ofthe platform.
STEP 2: SECURE THE BRACES
Take the brace of the ladder (9) and screw it to the nipples (8) or curved feet (6 and 7) mounted
in step 1. Mount the brace from the side of the of the platform (1) using the two screws (10) and
closed nuts (12). Mount the nut from the side of the platform (1). (fig. 1).
NOTE:The nuts and screws must be securely tightened, however, do not tighten them excessively;
excessive tightening may cause damage to the parts of the ladder.
STEP 3: FIX THE PLASTIC STEPS TOTHE LEGS
NOTE: Proceed from the bottom of the legs upwards. Make sure that the steps are oriented evenly
in relation to the legs. During assembly, it will not then be possible to dismount the steps without
damagingthem.Thelegs aresymmetrical,buttheir curvedfeet must faceawayfrom oneanother
(fig. 2).
Attach the two-part sleeve [3] to the leg [5] at the point of the depression (fig. 2) and secure it
witha rubber ring[13]. Pushthe step[2] ontothe sleevefrom aboveuntilthe locks clickinto place
on the sleeves under the upper edge of the hole in the step.
STEP 4: FIX THE LEGS TO THE HANDRAILS
From below, slide the legs assembled in step 3 onto the handrails (4) mounted on the platform
(1). Make sure that the holes in the handrails (4) are aligned with the holes in the platform (1)
and in the legs. Screw them together using 2 screws (11) and closed nuts (12). Insert the screws
from the outside of the platform.
The ladder is now ready for use.
INSTRUCTIONS FOR ASSEMBLY
2.0 ASSEMBLY
EN
Fig. 1
Fig. 2
Fig. 3
