Moultrie ATV User manual
INSTALL GATE
MOUNT HOPPER TO FRAME
INSTALL FEEDGATE ARM
Using a 9/16” socket wrench and a wrench,
attach the Gate to the outside bottom of the
Hopper using the 3/8” x 1.5” bolt, two washers
and nut. The bolt head, a washer, and the Gate
go on the outside-bottom of the hopper. A nut
and a washer go on the inside of the hopper.
Tighten such that some pressure is required to
move side to side.
Place the Hopper upside down with the frame on top such that
the holes in the Frame align with that of the Hopper and the
Gate is centered over the motor spinner plate. Using a 7/16”
socket wrench and a wrench, attach the Hopper to
the Frame using four 1/4” x 1.5” bolts, eight
washers and four nuts. The bolt head and a washer
go on the inside of the hopper. The nut and a
washer go on the outside, against the frame
With the Hopper upside down, slide the Lever
through the hole in the back plate of the Frame
Assembly and insert the end into the hole on the
Gate such that the Lever is pointing downward.
Place a cotter pin through the hole in
the Lever. Using pliers, bend the legs
of the cotter pin apart to secure the
Arm to the Gate
inside the hopper
Instructions for ATV Food Plot Spreader
THANK YOU for your purchase of the Food Plot Spreader, a
top quality Moultrie product. Please read both sides of this sheet
before operating this unit. If you should have any questions
about this or any other Moultrie product, please contact us using
the information on the reverse side.
To help us better serve you, please complete and mail the
enclosed Warranty Card.
ADJUST DISPENSING AMOUNT
The adjustment stop on the Lever allows you to
set the opening on the bottom of the hopper to the
amount of material you wish to dispense. Set the
adjustment stop on the Lever to the desired opening.
ADD MATERIAL
Add desired material such as feed, fertilizer, seed,
etc. to the hopper. Cover the hopper with the
plastic cover to prevent spillage.
SPREAD MATERIAL
You are now ready to use the Food Plot
Spreader. Turn the motor switch to the “On”
position. If the motor will not spin, check the
battery connections. While driving forward,
push Lever to open Gate. Pull Lever to close Gate.
CLEAN AND STORE SPREADER
Completely wash and dry the Food Plot Spreader. A light coat of oil on metal parts and motor will
help prevent rusting. Store Spreader in a dry location.
OPERATING INSTRUCTIONS
BE SURE SWITCH IS IN THE OFF POSITION.
Plug the provided Power Cable into the wire connector on the motor.
Attach the positive alligator clip to the positive battery terminal and the negative alligator clip to the
negative battery terminal on the ATV.
CONNECT POWER CABLE
Slide the two square channel Mounting Tubes onto the frame assembly such that they angle out - away
from the Spreader. Insert the C clips into the holes on the Mounting Tabs. Pull the Lever all the way
out (fully closed).
Hold the fully assembled Food Plot Spreader over the rear rack of the ATV such that there is
approximately a 1” gap between the Lever and the rear of ATV rack. Use the provided four U bolts,
top plates, and nuts to clamp the locations in which the Mounting Tube cross/intersect the bars on the
ATV rack.
Once the U bolts are connected, the C clips may be removed for a quick disconnect of the Food Plot
Spreader.
MOUNT ON ATV RACK
032005R05 / MFK-FPS
Table of contents
Other Moultrie Spreader manuals
Popular Spreader manuals by other brands
Fisher
Fisher POLY-CASTER 78601 owner's manual
TurfEx
TurfEx RS7200 Owner's/operator's manual
Ferris
Ferris Pathfinder Series Operator's manual
Fayat Group
Fayat Group DYNAPAC S100 operation & maintenance
Art's-Way Manufacturing
Art's-Way Manufacturing X700 Operator's manual & parts list
EASTMAN
EASTMAN CR 500 instruction manual
