Motorola Symbol LS1203 User manual

Symbol LS1203

Quick Reference Guide

2 Symbol LS1203

reserved.

Motorola reserves the right to make changes

to any product to improve reliability, function,

or design.

Motorola does not assume any product liability

arising out of, or in connection with, the

application or use of any product, circuit, or

application described herein.

No license is granted, either expressly or by

implication, estoppel, or otherwise under any

patent right or patent, covering or relating to

any combination, system, apparatus,

machine, material, method, or process in

which Motorola products might be used. An

implied license exists only for equipment,

circuits, and subsystems contained in Motorola

products.

MOTOROLA, the Stylized M Logo and Symbol

and the Symbol logo are registered

trademarks of Motorola, Inc. Other product

names mentioned in this manual may be

trademarks or registered trademarks of their

respective companies and are hereby

acknowledged.

Motorola, Inc.

One Motorola Plaza

Holtsville, N.Y. 11742-1300

http://www.motorola.com/enterprisemobility

Warranty

For the complete Motorola hardware product

warranty statement, go to:

http://www.motorola.com/enterprisemobility/warranty

Patents

This product is covered by one or more

patents. For patent information go to:

http://www.motorola.com/enterprisemobility/patents

Connect/Disconnect

Cable

Connect Host Interface

Keyboard Wedge Interface

RS-232 Interface

USB Interface

4 Symbol LS1203

Aim and Scan

012345 012345

Triggered/Auto-scan Modes

NOTE See Scanning Modes

on page 6.

TRIGGERED MODE

AUTO-SCAN MODE

6 Symbol LS1203

Parts of the Scanner

Scanning Modes

The scanner can operate in two modes:

•

Triggered mode - trigger button must be

pressed to emit the laser in order to a

scan bar code.

•

Auto-scan mode - scanner laser is in

constant on state and no trigger button

press is required to scan a bar code.

To toggle between modes, scan

TRIGGERED/AUTO-SCAN bar codes on

page 5.

For example, if the scanner is in triggered

mode, scan AUTO-SCAN MODE to switch

to auto-scan mode. If the scanner is in

auto-scan mode, scan TRIGGERED

MODE to switch to triggered mode.

NOTE When the scanner is

not used for an extended

period of time in auto-scan

mode, it enters sleep mode.

To wake the scanner, press

the trigger button.

LED

Trigger

Button

Scan

Window

Troubleshooting

Problem Possible

Cause Possible

Solutions

Nothing

happens

when the

scan button

is pulled.

No power to

the scanner.

Check system

power. Ensure

power supply is

connected.

Interface or

power

cables are

loose.

Ensure all cable

connections are

secure.

Laser

comes on,

but symbol

does not

decode.

Scanner not

programmed

for correct

bar code

type.

Ensure scanner

is programmed

to read the type

of bar code

scanned. Refer

to the Symbol

LS1203

Product

Reference

Guide, p/n

72E-73953-xx,

for more

information.

Bar code

symbol is

unreadable.

Check the

symbol to

ensure it is not

defaced. Try

scanning

another bar

code type.

Distance

between

scanner and

bar code is

incorrect.

Move scanner

closer to or

further from the

bar code.

Symbol is

decodedbut

not

transmitted

to the host.

Scanner not

programmed

for the

correct host

type.

Scan the

appropriate

host type bar

code.

8 Symbol LS1203

Beeper Definitions

The scanner issues different beep

sequences and patterns to indicate status.

The table below defines beep sequences

that occur during both normal scanning and

while programming the scanner.

NOTE For detailed

troubleshooting, refer to the

Symbol LS1203 Product

Reference Guide, p/n

72E-73953-xx.

Beeper

Sequence Indication

Standard Use

Low/medium/high

beep

Power up.

Short high beep A bar code symbol was

decoded (if decode beeper

is enabled).

4 long low beeps A transmission error was

detected in a scanned

symbol. The data is

ignored. This occurs if a

unit is not properly

configured. Check option

setting.

5 low beeps Conversion or format

error.

Low/high/low

beep

ADF transmit error.

High/high/high/

low beep

RS-232 receive error.

Parameter Menu Scanning

Short high beep Correct entry scanned or

correct menu sequence

performed.

Low/high beep Input error, incorrect bar

code or Cancel scanned,

wrong entry, incorrect bar

code programming

sequence; remain in

program mode.

High/low beep Keyboard parameter

selected. Enter value

using bar code keypad.

High/low/high/

low beep

Successful program exit

with change in the

parameter setting.

Low/high/low/

high beep

Out of host parameter

storage space. Scan SET

DEFAULTS on page 86.

Code 39 Buffering

High/low beep New Code 39 data was

entered into the buffer.

3 beeps - long

high beep

Code 39 buffer is full.

Low/high/low

beep

The Code 39 buffer was

erased or there was an

attempt to clear or transmit

an empty buffer.

Low/high beep A successful transmission

of buffered data.

Host Specific

USB only

4 short high

beeps

Scanner has not

completed initialization.

Wait several seconds and

scan again.

Scanner gives a

power-up beep

after scanning a

USB Device

Type.

Communication with the

bus must be established

before the scanner can

operate at the highest

power level.

Beeper

Sequence Indication

10 Symbol LS1203

LED Definitions

In addition to beeper sequences, the

scanner communicates with the user using

a two-color LED display. The table below

defines LED colors that display during

scanning.

Programming Bar Codes

Descriptions

This guide includes the programming bar

codes required to set up the scanner to

work with various host interfaces. Some

frequently used programming bar codes

are also included.

For all programming bar codes and detailed

information about the scanner, go to:

http://www.symbol.com/services/manuals

The power-up

beep occurs

more than once.

The USB bus may put the

scanner in a state where

power to the scanner is

cycled on and off more

than once. This is normal

and usually happens when

the host PC cold boots.

RS-232 only

1 short high beep A <BEL> character is

received and Beep on

<BEL> is enabled.

LED Indication

Off No power is applied to the scanner,

or the scanner is on and ready to

scan.

Green A bar code was successfully

decoded.

Red A data transmission error or

scanner malfunction occurred.

Beeper

Sequence Indication

Other manuals for Symbol LS1203

Table of contents

Languages:

Motorola Symbol LS1203 User manual

Popular Barcode Reader manuals by other brands