Montigo Proflame 2 Manual
®
C US
XG0677 141231
Proame 2
System
Operation & Maintenance Manual
Read these instructions before use.
NOTICE
FIRE HAZARD. Can cause severe injury or death. The Transmitter and IFC
.
WARNING
device causes ignition of the appliance. The appliance can turn on suddenly.
Keep away from the appliance burner when operating the remote system or
activating manual bypass of the remote system.
Property Damage Hazard. Excessive heat can cause property damage.
The appliance can stay lit for many hours. Turn off the appliance if it is not going
be attended for any length of time.
.
CAUTION
- Turn OFF the main gas supply of the appliance during installation or
maintenance of the receiver device.
- Turn OFF main gas supply to the appliance prior to removing ro reinserting the
batteries.
- In case of remote control malfunction turn OFF the IFC device using the On/Off
main switch.
- For installation / maintenance switch OFF the IFC device by removing main
power supply plug and disconnect.
ATTENTION
Do not operate in presence of water dripping, spraying, rain, etc.
WARNING
Canadian Heating Products Inc. Langley, BC V4W 4A1 | Montigo Del Ray Corp. Ferndale, WA 98248
WARNING
When installing the replace - gas lines, ttings,
accessories or any other objects cannot impede the
proper movement of the door buckles.
Page 2
Proame 2 Transmitter
XG0677 - 141231
Operation
The Proflame Transmitter 2 is an integrated part of the Proflame 2 System,
which consists of these elements:
- Proflame 2 Transmitter, to be used in conjunction with:
- Integrated Fireplaces Control (Proflame 2 IFC)
IMPORTANT
The Proame 2 Transmitter controls the
following replace functions:
1. Main Burner On/Off
2. Main Burner ame modulation (6 levels).
3. Choice of standing or intermittent pilot (CPI/IPI).
4. Thermostat and Smart thermostat functions.
5. Accent light On/Off.
6. Comfort fan speed modulation (6 levels).
The Proame 2 Transmitter uses a streamline design with
a simple button layout and informative LCD display, see
gure 1. A Mode Key is provided to index between the
features and a Thermostat Key is used to turn On/Off or
index through Thermostat functions, see gure 1 & 3.
Additionally, a Key Lock feature is provided, see gure 15.
The Proame 2 System consists of the
following elements:
1. Pilot Assembly
2. Proame Gas Valve.
3. Proame 2 Control Module
4. Wiring Harness
5. Variable Speed comfort fan *
6. Accent Lights *
7. Proame 2 remote control
8. Battery Pack (not applicable for power vented units)
9 Manual override switch
.
WARNING
Do not expose remote control to temperatures below 0°C (32°F) or above 50°C (122°F)
* Not available on all replace models. Refer to the
replace instruction guide for available features.
Page 3
Proame 2 Transmitter
XG0677 - 141231
Operation
Figure 1. Proame Remote Control
Figure 2. Proame Control Module
SW1LED1
LED2
SW1 = Programing Button
LED1 = Red Diagnostic Light
LED2 = Amber Programing Remote Control Light
Blue Back lit LCD display
On/Off Key
Thermostat Key
Up/Down Arrow Key
Mode Key
Page 4
Proame 2 Transmitter
XG0677 - 141231
Operation
Figure 3. Remote Control LCD display.
Initializing the System for the rst time
1. Install four (4) AA batteries into the battery holder
located under the rebox. (Not applicable for Power
Vented Units)
2. Install three (3) AAA batteries in the back of the remote
control, see gure 4a.
Note the polarity of batteries and install them as indicated
by the silk screen (+/-) on the holder.
3. Set manual switch to OFF position, see gure 6.
4. Connect AC Power (120 volts, 60 Hz) to replace.
Operating the System for the rst time
5. Press SW1 button on the control module. The control
module will beep three (3) times and amber LED, see
gure 2, is illuminated to indicate that the IFC is ready
to synchronize with a remote control within 10 sec. Push
the ON button. The control module will "beep" four (4)
times to indicate transmitter's command is accepted.
The System is now initialized.
Figure 4a. Remote control battery compartment.
Battery operated device. Read the battery instructions before installing them
.
WARNING
into the system. Do not expose any battery, or its holder, or a device in which
batteries are installed, to a working temperature greater than 54°C / 129°F.
Avoid battery overheating even if the working temperature of the device to which
the batteries are connected is reported to be greater than 54°C / 129°F. In case
of overheating the bad cases, develop hydrogen gas and explode.
Figure 4. Control Module Battery Pack
(Not applicable for Power Vented Units)
Page 5
Proame 2 Transmitter
XG0677 - 141231
Operation
Temperature indication Display
With the system in the "Off" position, press the
Thermostat Key and the Mode Key at the same time.
Look at the LCD screen on the Remote Control to
verify that a C or F is visible to the right of the Room
Temperature display, see gure 5 .
Turn On the Fireplace
With the system Off, turn the manual On/Off switch to on
and press the On/Off Key on the Remote Control. The
manual On/Off switch is located on the right side of the
replace under the valve blind cover. The Remote Control
display will show some other active Icons on the screen.
At the same time the Control Module will activate the
replace. A single "beep" from the Control Module will
conrm reception of the command.
Turn Off the Fireplace
With the system On, press the On/Off Key on the
Remote Control. The Remote Control LCD display will
only show the room temperature, see gure 7. At the
same time the Control Module will turn off the replace. A
single "beep" from the Receiver conrms reception of the
command.
Figure 7. Remote Control display.
Remote-Flame Control
The proame has six (6) ame levels. With the system
on, and the ame level at the maximum in the replace,
pressing the Down Arrow Key once will reduce the ame
height by one step until the ame is turned off.
The Up Arrow Key will increase the ame height each
time it is pressed. If the Up Arrow Key is pressed while
the system is on but the ame is off, the ame will come
on in the high position, see figure 8 & 9.
Figure 8. Flame Off and Flame Level 1.
Figure 9. Flame Level 5 and Flame Level Maximum.
Figure 5. Remote Control display in Farenheit & Celsius.
Figure 6. Manual On/Off Switch
Page 6
Proame 2 Transmitter
XG0677 - 141231
Operation
Figure 10. Setting Room Thermostat
Smart Thermostat (Remote Control ........
Operation)
The Smart Thermostat function adjusts the ame height
in accordance to the difference between the set point
temperature and the actual room temperatures. As the
room temperature gets closer to the set point the Smart
FUnction will modulate the ame down. To activate
the function, press the Thermostat Key, see gure
1, until the word "SMART" appears to the right of the
temperature bulb graphic, see gure 11.
NOTE: When smart Thermostat is activated, manual
ame height adjustment is disabled.
Figure 11. Smart ame function
Fan Speed Control
The replace may be equipped with a hot air circulating
fans. The speed of the fan can be controlled by the
Proame system. The fan speed can be adjusted through
six (6) speeds. To activate this function use the Mode
Key, see gure 1, to index to the fan control icon, see
gure 12. Use the Up/Down Arrow Keys, see gure 1,
to turn on, off, or adjust the fan speed, see gure 12. A
single "beep" will conrm reception of the command.
Figure 12. Fan Speed Control
Accent Light Control
The replace may be equipped with accent lights. The
auxiliary function controls the Accent Lights. To activate
this function use the Mode Key, see gure 1, to index to
the AUX icon, see gure 13.
Pressing the Up Arrow Key will turn the light on. Pressing
the Down Arrow Key will turn the light off. A single "beep"
will conrm the reception of the command.
Figure 13. Light Control
Room Thermostat (Remote Control ........
Operation)
The Remote Control can operate as a room thermostat.
The thermostat can be set to a desired temperature
to control the comfort level in a room. To activate the
function, press the Thermostat Key, see gure 1. The
LCD display on the remote control will change to show
that the room thermostat is "On" and the set temperature
is now displayed, see gure 10. To adjust the set
temperature press the Up or Down Arrow Keys until the
desired set temperature is displayed on the LCD screen
of the Transmitter.
Page 7
Proame 2 Transmitter
XG0677 - 141231
Operation
Continuous Pilot (CPI) Selection .............
(Optional)
In cold weather climates, the pilot burner can stay
on continuously to prevent condensation or cold air
temperatures near the replace glass. Note, some
jurisdictions do no permit use of continuous pilot system.
Check local codes or contact your Montigo dealer.
WARNING:
Do NOT use CPI with optional Power Vent.
With the system in "off" position press the Mode Key, see
gure 1, to index to the CPI mode icon, see gure 14.
Pressing the Up Arrow Key will activate the Continuous
Pilot Ignition mode (CPI). Pressing the Down Arrow Key
will return to IPI. A single "beep" will conrm the reception
of the command.
NOTE:
- Requires CPI switch (not supplied).
- Set the CPI/IPI switch to CPI position (Switch closed) to
enable remote CPI/IPI operation.
- Set the CPI/IPI switch to IPI position (switch open) to
disable remote CPI/IPI operation. The system will now
work in IPI mode only regardless of the selection on the
remote control hand set.
Figure 14. Continuous Pilot / Intermittent Pilot Selection
Key Lock
This function will lock the keys to avoid unsupervised
operation. To activate this function, press the Mode and
Up Keys and the same time, see gure 15. To de-
activate this function, press the Mode and Up Keys and
the same time.
Figure 15. Key Lock
Page 8
Proame 2 Transmitter
XG0677 - 141231
Maintenance
Remote Control
When the Remote Control batteries are low, a Battery
Icon will appear on the LCD display of the Remote
Control, see gure 16, before all battery power is lost.
When the batteries are replaced this icon will disappear.
Figure 16. Low Battery Power Detection
Control Module
(Not applicable for Power Vented Units)
When the Control Module batteries are low, a "double-
beep" will be emitted from the IFC when it receivers
an On/Off command from the Remote Control. This is
an alert for a low battery condition of the receiver and
after that no more command will be accepted. When the
batteries are replaced the "beep" will be emitted from the
receiver as soon as powered.
Low Battery Power Detection
The life span of the batteries depends on various factors:
quality of the batteries used, the number of ignitions
of the appliance, the number of changes to the room
thermostat set point, etc.
Problem Solution
Control module beeps
twice when On/Off button
on remote is pressed and
Red LED is On.
Replace batteries in battery
pack.
(Not applicable for Power Vented Units)
Lights and Fans will not
turn On.
Check main power is On.
Pilot will not spark. Check and turn main On/Off
switch to On.
Main burner will not light. Check wiring
Troubleshooting:
Below is a list of possible problems and solutions.
Page 9
P52DF* Indoor Gas Fireplace
XG0196 -141231
Notes
XG0196 - 141231
Proame 2
System
Other manuals for Proflame 2
1
Table of contents
Other Montigo Indoor Fireplace manuals
Montigo
Montigo T34DF-PV Manual
Montigo
Montigo P42DF Prestige Series Instruction Manual
Montigo
Montigo M38DVM Wiring diagram
Montigo
Montigo HL34 Instruction Manual
Montigo
Montigo MW38-BV User manual
Montigo
Montigo 36ST Wiring diagram
Montigo
Montigo M36PFC Wiring diagram
Montigo
Montigo DelRay DRL7213NI Instruction Manual
Montigo
Montigo L52-DF Instruction Manual
Montigo
Montigo H38SVO-ST Series Manual
Montigo
Montigo R320 Instruction Manual
Montigo
Montigo C34-DV Owner's manual
Montigo
Montigo H38DF ST Instruction Manual
Montigo
Montigo Proflame 2 Upgrade Kit RX 200 NG User manual
Montigo
Montigo 30FID Traditional Instruction Manual
Montigo
Montigo R520 Instruction Manual
Montigo
Montigo HR38DF Instruction manual
Montigo
Montigo L42DF series Instruction Manual
Montigo
Montigo Wildfire W34-DW Owner's manual
Montigo
Montigo 36NR Wiring diagram
Popular Indoor Fireplace manuals by other brands
Brigantia
Brigantia 35-DVRS31N-2 User's installation, operation and maintenance manual
Nordpeis
Nordpeis Bergen Installation and user manual
Superior
Superior BCT2536TMN Installation and operation instructions
Quadra-Fire
Quadra-Fire 5100I-GD-B owner's manual
Renaissance
Renaissance RUMFORD 1000 user manual
Lacunza
Lacunza IV-800 Instruction book
Baxi
Baxi 940 Installer and owner guide
Dru
Dru Maestro 60/2 Tall RCH installation manual
Diamond Fireglass
Diamond Fireglass SS-O22 General assembly, installation, and operation instructions
HearthStone
HearthStone Windsor Bay 8830 Owner's manual and installation guide
Napoleon
Napoleon ASCENT B42 quick start guide
Enviro
Enviro E33GI owner's manual
Smeg
Smeg L30 FABE Installation & user's instructions
KEDDY
KEDDY K700 Installation instructions care and firing instructions
Godin
Godin 3451 manual
Jøtul
Jøtul Jotul GI 535 DV IPI New Harbor Installation and operation instructions
Austro Flamm
Austro Flamm Heidi Back 2.0 945048 operating manual
Desa
Desa CCFPDFT Owner's operating & installation manual