Monstertech MTX HOTAS User manual
MTX HOTAS
Instruction Manual EN
MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL
2 3
1 General information
This guide is meant to help you assemble your Sim Rig as smoothly as possible. If you still
monstertechusa.com.
1.1 Before you start
Before you start the assembly, we are going to look at some common assembly steps and of-
ten used parts, as well as required tools.
1.1.1 Required Tools
For our assembly, we need following tools*:
- Hex key set with ball head with extension
- Rubber or plastic mallet
- Flat head screwdriver
- Tape measure w/ millimeters
*Tools are not included with the Sim Rig
1.1.2 Inserting T-Nut into Profile
There are two ways to insert the M8 T-Nuts into the respective prole groove; refer to Figure 1
and 2 respectively.
Figure 1: Slide in from side
Figure 2: Rotate in from top
MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL
4 5
1.1.3 Universal Fastener Assembly
The universal fastener assembly can be prepared the following way, so long as the T-Nut can
be slid in from the side. One Universal Fastener Assembly is made up from one (1) M8x30 Hex
Screw, one (1) T-Nut, and one (1) Universal Fastener.
Figure 3: Universal fastener assembly
If inserting the universal fastener assembly from the side is not possible, it is necessary to rota-
te the T-Nut into the prole groove rst, and then screw the M8x30 bolt (along with the univer-
sal fastener) into the T-Nut.
1.1.4 Angle Bracket Stud Removal
Sometimes it might be necessary to break off the studs from angle brackets (if those are part
of the product). This is best achieved by:
1. Inserting a at-head screwdriver between the stud and the bracket, and then
2. Rotate the screwdriver for the stud to come off
MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL
6 7
1.1.5 Angle Bracket Assembly
For some assemblies the use of angle brackets is required. These are prepared by using two
(2) M8x18 hex screws, two (2) washers, and two T-Nuts.
Figure 5: Angle bracket assembly
1.1.6 Adjustment of Profile Feet
The prole feet are installed on the MTX HOTAS or MTX Stand-Alone TV
Figure 6: Prole feet
2 Overview
2.1 Completed MTX HOTAS
HOTAS - Overview
Figure 8:
Use the above image as reference for the following assembly inst-
ructions.
MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL
8 9
3.1
Figure 9: HOTAS assembly - step 1
3.2
Figure 10: HOTAS assembly - step 2
3.3
Figure 11: HOTAS assembly - step 3
3.4
Figure 12: HOTAS assembly - step 4
MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL
10 11
3.5
Figure 13: HOTAS assembly - step 5
3.6
Figure 14: HOTAS assembly - step 6
3.7
Figure 15: HOTAS assembly - step 7
3.8
Figure 16: HOTAS assembly - step 8
Attention: Please use the in-
cluded grey corner brackets
instead of the clamps.
Achtung: Bitte die grauen
Winkel anstatt die Klemmhe-
bel verwenden.
Attention: Please use the in-
cluded grey corner brackets
instead of the clamps.
Achtung: Bitte die grauen
Winkel anstatt die Klemmhe-
bel verwenden.
MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL
12 13
3.9
Figure 17: HOTAS assembly - step 9
3.10
Figure 18: HOTAS assembly - step 10
3.11
Figure 19: HOTAS assembly - step 11
3.12
Figure 20: HOTAS assembly - step 12
MTX HOTAS INSTRUCTION MANUAL MTX HOTAS INSTRUCTION MANUAL
14 15
3.13
Figure 21: HOTAS assembly - step 13
WARNHINWEISE
GEFAHR: Nicht für Kinder unter 3 Jahren,
Kleinteile - Verschluckungsgefahr!
Nur für Kinder ab 12 Jahren und Erwachsene
Alle MONSTERTECH Produkte sind handgefertigt und
qualitätsgeprüft.
Das Rennsitzgestell ist zur Verwendung in Kombination mit
einem Autositz und nur zur Verwendung im Innenbereich
ausgelegt.
Wir übernehmen keine Haftung für zweckentfremdete
Benutzung.
Bei Fragen zur Sicherheit oder Aufbau des Rennsitzgestells,
wenden Sie sich an info@monstertech.de oder besuchen
unsere Website unter www.monstertech.de.
WARNING NOTICES
NOTE: Contains small parts not suitable for children under 3
years.
Only suitable for children over 12 years and adults.
All MONSTERTECH products are handmade and quality
checked.
The racing frame is only designed for inside usage in
combination with a car seat.
We exclude liability if the product is used for purposes other
than intended.
If you have safety concerns or questions regarding assembly,
contact us under info@monstertech.de or visit
www.monstertech.de.
Table of contents
Other Monstertech Rack & Stand manuals
Monstertech
Monstertech STAND User manual
Monstertech
Monstertech Wall Holder User manual
Monstertech
Monstertech MFD User manual
Monstertech
Monstertech MFD/TABLET MOUNT CENTER User manual
Monstertech
Monstertech CHAIR MOUNT KEYBOARD TRAY User manual
Monstertech
Monstertech FLIGHT STAND User manual
Monstertech
Monstertech JOYSTICK/HOTAS TABLE MOUNT User manual
Monstertech
Monstertech CHAIR MOUNT INSTRUMENT CARRIER User manual
Monstertech
Monstertech MTS CENTER JOYSTICK User manual
Monstertech
Monstertech CHAIR MOUNT UNIVERSAL BASE User manual
Popular Rack & Stand manuals by other brands
Salamander
Salamander Acadia AC/W/L400/WH Assembly instructions
Fohhn
Fohhn VAT-09 Mounting instruction
ricoo
ricoo FS0522 quick start guide
AMSOIL
AMSOIL BMK-22 Installation and service instructions
Kargo Master
Kargo Master 48220 installation guide
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 installation instructions
