Moeller Teleservice XC100 Quick guide

Moeller GmbH

Industrieautomation

Hein-Moeller-Straße 7–11

D-53115 Bonn

E-Mail: info@moeller.net

Internet: www.moeller.net

Subject to alteration

AWB2724-1490GB xx/xx/Ki 07/04

Printed in the Federal Republic of Germany (0x/02)

Article No.: xxxxxx

Think future. Switch to green. Think future. Switch to green.

SystemsIndustrial Automation

Hardware, Engineering, Configuration

07/04 AWB2724-1490GB

Teleservice

XC100

Building Automation

All brand and product names are trademarks or registered

trademarks of the owner concerned.

1st published 2003, edition date 04/03

2nd published 2004, edition date 07/04

See revision protocol in the “About this manual“ chapter

Author: Werner Albrecht

Editor: Thomas Kracht

Translator: David Long

No part of this manual may be reproduced in any form

(printed, photocopy, microfilm or any other process) or processed,

duplicated or distributed by means of electronic systems without

written permission of Moeller GmbH, Bonn.

Subject to alteration without notice.

Before commencing the installation

• Disconnect the power supply of the device.

• Ensure that devices cannot be accidentally

restarted.

• Verify isolation from the supply.

• Earth and short circuit.

• Cover or enclose neighbouring units that

are live.

• Follow the engineering instructions (A A)

of the device concerned.

• Only suitably qualified personnel in

accordance with EN 50110-1/-2

(VDE 0105 Part 100) may work on this

device/system.

• Before installation and before touching

the device ensure that you are free of

electrostatic charge.

• The functional earth (FE) must be

connected to the protective earth (PE) or

to the potential equalisation. The system

installer is responsible for implementing

this connection.

• Connecting cables and signal lines should

be installed so that inductive or capacitive

interference does not impair the

automation functions.

• Install automation devices and related

operating elements in such a way that they

are well protected against unintentional

operation.

• Suitable safety hardware and software

measures should be implemented for the

I/O interface so that a line or wire breakage

on the signal side does not result in

undefined states in the automation

devices.

• Ensure a reliable electrical isolation of the

low voltage for the 24 volt supply. Only

use power supply units complying with

IEC 60364-4-41 (VDE 0100 Part 410) or

HD 384.4.41 S2.

• Deviations of the mains voltage from the

rated value must not exceed the tolerance

limits given in the specifications, otherwise

this may cause malfunction and dangerous

operation.

• Emergency stop devices complying with

IEC/EN 60204-1 must be effective in all

operating modes of the automation

devices. Unlatching the emergency-stop

devices must not cause restart.

• Devices that are designed for mounting in

housings or control cabinets must only be

operated and controlled after they have

been installed with the housing closed.

Desktop or portable units must only be

operated and controlled in enclosed

housings.

Moeller GmbH

Safety instructions

Warning!

Dangerous electrical voltage!

• Measures should be taken to ensure the

proper restart of programs interrupted

after a voltage dip or failure. This should

not cause dangerous operating states even

for a short time. If necessary, emergency-

stop devices should be implemented.

• herever faults in the automation system

may cause damage to persons or property,

external measures must be implemented to

ensure a safe operating state in the event

of a fault or malfunction (for example, by

means of separate limit switches,

mechanical interlocks etc.).

07/04 AWB2724-1490GB

Contents

About this manual 3

List of revisions 3

Structure 3

Abbreviations and symbols 3

Further documentation 3

1 General 5

Range of applications 5

Hardware/Software requirements 5

2 XC100/X200 – PC Connection 7

Physical structure of the connection (overview) 7

Connection PC – modem or modem – XC100/XC200 7

Connection PC – TD32B modem 7

– Cable layout 7

Modem TD32B – XC100/XC200 connection 8

– Cable layout 8

Connection modem – modem 8

– Telecontrol cable connection 8

– Handshake lines 8

– Connection via 2-/4-wire leased line 9

– Connection via dial-up line 9

Modem settings 10

– Dial-up line 10

– Leased line 12

LED status indication 13

3 Programming 15

Modem connection via leased and dial-up lines 15

Connection between PC and control 16

ONLINE modification 16

Index 17

07/04 AWB2724-1490GB

About this manual

List of revisions

The following are the main changes and amendments which have

been made since the last edition of this manual:

Structure

This manual describes the steps necessary for remote

programming of XC100/XC200. It describes the installation,

device configuration and parameter allocation of communication

components.

This manual does not replace the modem manufacturer's operator

manual. It is essential that you note and adhere to the modem

documentation.

This manual refers to the use of Type TD32B DC analog modem

from Messrs. Westermo. This modem is suitable for leased-line

and dial-up line connection.

Abbreviations and symbols

Symbols used in this manual have the following meanings:

XIndicates actions to be taken.

Select ‹File rNew› means: activate the instruction “New” in the

“File” menu.

For clarity of layout, we adhere to the following conventions in this

manual: at the top of left-hand pages you will find the Chapter

heading, at the top of right-hand pages the current Section

heading; exceptions are the first pages of Chapters and empty

pages at the end of Chapters.

Further documentation

• XSoft, Programming software (h1437g.pdf)

• XI/OC signal modules, Hardware and engineering (h1452g.pdf)

• XC-CPU101-..., Hardware, Engineering and Functional

Description (h1453g.pdf)

• XC-CPU201-..., Hardware, Engineering and Functional

Description (h1491g.pdf)

• Function blocks for XSoft (h1456g.pdf)

• Installation manual TD-32/485; TD32 (Messrs. Westermo)

6178-2303.

These manuals are available as online PDF files, with the exception

of the installation instruction from Messrs. Westermo which is

supplied on a CD.

The most current and up-to-date edition of the manual can also be

found under http://www.moeller.net/support: search term: e.g.

“AWB2725-1452G”.

Edition date Page Description Change

07/04 8 „Handshake lines“ j

10 „Modem settings“ j

15 „Programming“ j

Modem A modem is used for conversion of signals from a

data terminal into electrical signals and vice versa

Note!

Warns of a hazardous situation that could result in

damage to the product or components.

Caution!

Warns of the possibility of a hazardous situation that

could result in major damage and minor injury.

Warning!

Warns of the possibility of a hazardous situation that

could result in major damage and serious or fatal injury/

death.

07/04 AWB2724-1490GB

1 General

Range of applications

The telecontrol service for XC100/XC200 is intended for use

wherever PC and XC100/XC200 controller are at different

locations, and the connection therefore has to be established via

analog modem and leased or dial-up line.

The telecontrol service enables user program download, ONLINE

modification and status indication in the RUN mode.

Hardware/Software requirements

•Hardware

– Programming PC

– XC-CPU101/201-...-8DI-6DO (-XV)

– Analog modem: TD32B

– Analog leased line or dial-up line.

•Software

– XSoft programming software.

07/04 AWB2724-1490GB

Table of contents

Other Moeller Control Unit manuals

Moeller

Moeller Xcomfort CAEE-02/01 User manual

Moeller

Moeller LE 4-505-BS1 User manual

Moeller

Moeller DILM32-XTE Series User manual

Moeller

Moeller EMR4-RDC-1-A User manual

Moeller

Moeller RA-MO Series User manual

Moeller

Moeller EMR4-I1-1-A User manual

Moeller

Moeller EASY205-ASI User manual

Moeller

Moeller S40-AM-TD User manual

Moeller

Moeller WINbloc eco PROFIBUS-DP Series User manual

Moeller

Moeller S40-AM-TL User manual

Moeller

Moeller F&G Xcomfort CRCA-00/02 User manual

Moeller

Moeller NZM3-XD User manual

Moeller

Moeller XC-CPU101 Series Guide

Moeller

Moeller EASY221-CO User manual

Moeller

Moeller XIOC AWB2725-1452GB User manual

Moeller

Moeller Room-Manager User manual

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual