Modern Fan Co Cloud User manual

THE MODERN FAN COMPANY

Customer Service

M-F 8am - 4pm (PST)

(ph) 888.588.3267

www.modernfan.com

(1) Remove and identify contents of carton.

Cloud Fan- Installation instructions

Should you have any questions or difficulty installing your new fan, please contact

Modern Fan Co. customer service immediately.

Note: Power supply must be turned off prior to any contact with electrical wires. It is

recommended that a licensed electrician be hired to install your ceiling fan.

Cloud

control(s)

balancing kit

hanging

bracket

blades

fan body

hardware

package

canopy

down rods

& half-ball

glass diffuser

LED board

LED adapter

plate

LED screws

LED cover

(2) Place fan body on either piece of packing foam, with wire bundle facing down and

bottom of fan facing up. Follow these steps (a) through (c) to attach LED

components to your fan:

(a) Align holes on adapter plate with holes on

switch housing. Using countersink screws

included with LED pack, secure adapter plate to

switch housing.

(b) Position and insert 2-pin connector into

terminal near center hole of LED board.

Position LED board flat on adapter plate so that

three cutouts are positioned over attachment

holes. Feed any excess wire back into switch

housing.

(6) Run fan wires through selected down rod. Reinstall

stopper screw from step (5) and firmly tighten set screw on

fan collar against down rod.

Note: If ceiling height allows, using a longer down rod will

increase airflow and efficiency.

(7) Insert one blade at at time into rotor slot, aligning with

“pie-slice” opening in black plate. Using blade screws from

hardware package, secure blade to rotor. Start all three

screws before completely tightening. Repeat for all blades.

(5) Remove the stopper screw and loosen the set screw on

the fan collar. Set the

stopper screw aside for step (6).

(3) Using packing foam to position fan body in an upright

and stable position, remove the rotor cover by loosening the

three cover screws. Set the

cover aside for reinstallation in step (8).

cover screws

(4) Remove stopper pin and half ball from small down rod

by loosening set screw on half ball. Set parts aside for

reinstallation in step (10).

stopper pin

set screw

stopper screw

set screw

(8) Making sure to align opening labeled “reverse” over the

reverse switch, reinstall rotor cover from step (3) by

tightening all three cover screws.

(9) Slide fan canopy over down rod and carefully rest on top

of fan body.

canopy

attachment holes are aligned with cutouts and

holes in adapter plate. Using three additional,

small pan head screws included with hardware

pack, secure LED cover and LED board to

adapter plate.

(12) Using machine screws from hardware package or

existing screws in junction box, securely attach hanging

bracket to ceiling junction box.

(11) Lift fan to ceiling and set half ball in the hanging

bracket so that the ridge on the edge of the hanging

bracket is seated in the slotted channel in the half ball.

channel and ridge

(13) With fan safely suspended by bracket, make wire connections with wire nuts

included in hardware package as described in the Control Installation Instructions.

If using optional #003, #004 or #005 controls, the receiving unit should be placed

inside the arms of the hanging bracket and connected at this time.

(10) Reinstall half ball from step (3) on end of down rod. Be

sure that stopper pin is inserted through down rod and

seated in half ball. Tighten set screw against down rod.

stopper pin

set screw

(14) Loosen and remove set screws on the sides of the

hanging bracket. Lift canopy to ceiling. Align slots on side

of canopy with set screw holes on hanging bracket, reinstall

and tighten set screws to hold canopy in place.

set screw

(16) Install wall control as described in the control installation instructions (unless

using the handheld remote control only).

(17) Your fan is reversible for summer and winter operation.

The reverse switch is located on the top of the fan body.

When reading the REVERSE label, the LEFT position is for

summer and the RIGHT position is for winter.

reverse switch

(15) Carefully install the glass shade using the thumb

screws included in the hardware package. The holes in the

glass shade must be aligned with the holes in the fan body.

Use extreme care and

do not over tighten.

Tip 1: A second pair of hands can be very helpful.

Tip 2: Only partly screw in each fastener until all three are

in place. Then tighten just firmly enough to keep glass from

moving. DO NOT overtighten.

(18) The rotor and motor of your fan have been dynamically balanced at the factory.

In addition, the blades have been matched to the nearest gram to ensure a well

balanced ceiling fan. Furthermore, a blade balancing kit has been included with your

fan. Please refer to the instructions packaged with the balancing kit should your fan

require additional balancing.

709 Washington Street • Ashland, OR 97520 • (tel) 888.588.3267 • (e) [email protected]

w w w . m o d e r n f a n . c o m

Table of contents

Other Modern Fan Co Fan manuals

Modern Fan Co

Modern Fan Co Arbor DC Series Quick start guide

Modern Fan Co

Modern Fan Co Torsion User manual

Modern Fan Co

Modern Fan Co Cirrus User manual

Modern Fan Co

Modern Fan Co DC Slim User manual

Modern Fan Co

Modern Fan Co Pensi User manual

Modern Fan Co

Modern Fan Co Cirrus Flush User manual

Modern Fan Co

Modern Fan Co Ball User manual

Modern Fan Co

Modern Fan Co Velo DC VEL Series Quick start guide

Modern Fan Co

Modern Fan Co Eclipse User manual

Modern Fan Co

Modern Fan Co IC/Air3 DC Series Quick start guide

Modern Fan Co

Modern Fan Co Stella User manual

Modern Fan Co

Modern Fan Co aurora flush User manual

Modern Fan Co

Modern Fan Co Velo Flush User manual

Modern Fan Co

Modern Fan Co Altus User manual

Popular Fan manuals by other brands

ELTA FANS

ELTA FANS H03VV-F installation guide

Hunter

Hunter 20714 Owner's guide and installation manual

Emerson

Emerson CARRERA VERANDA CF542ORB00 owner's manual

Hunter

Hunter Caraway Owner's guide and installation manual

Panasonic

Panasonic FV-15NLFS1 Service manual

Kompernass

Kompernass KH 1150 operating instructions

VES

VES FALA100/12V/TR Original instructions

Vertiv

Vertiv Liebert DCD user manual

Westinghouse

Westinghouse GFP Series owner's manual

Venmar

Venmar KUBIX HRV PLUS Series user guide

Maico

Maico ECR 31 installation instructions

Sonnenkonig

Sonnenkonig Dinky instruction manual

S&P

S&P ECOWATT HXBR manual

Wider

Wider IMP03369BH instruction manual

Panasonic

Panasonic F-60DHN Operating and installation instructions

Hinkley

Hinkley HIGHLAND instruction manual

Broan

Broan 766BN installation guide

Premium

Premium PFS16022 Use manual