Mobot 1 sec eBike User manual
MOBOT®1 sec eBike
Electric Bicycle
USER MANUAL
PLEASE CAREFULLY READ THE USER MANUAL AND
WARRANTY BOOK BEFORE USING
MOBOT® 1 sec eBike, edited on 7/12/2015
WARNING
Whenever you ride the MOBOT®1 sec eBike electric bicycle you
might risk having serious injury from collisions, falls or loss of
control. To ride safely, YOU MUST READ AND FOLLOW ALL
INSTRUCTIONS AND WARNINGS STATED IN THIS MANUAL.
This manual includes basic operational instructions for the
MOBOT®Freedom electric scooter. It does not cover any
situations where injury or death may occur.
OPERATORS MUST USE GOOD JUDGMENT AND COMMON
SENSE TO DETECT AND AVOID HAZARDS AND DANGERS that
they may encounter when riding the MOBOT®1 sec eBike
electric bicycle. By using the MOBOT® 1 sec eBike electric
bicycle, it deems that you accept the inherent risks of operating
this product.
2
Table of Contents
Table of Contents 3
APPEARANCE 4
MAIN PART 5
SAFETY 6
CLOSING STEPS 7
Circuit diagram of the 1 sec Folding e-bike 8
ATTENTION TO DETAIL DURING RIDING & 8
ADJUSTMENT OF MAIN PARTS 8
BATTERY AND CHARGER 12
MAINTENANCE 13
GENERAL TROUBLESHOOTING 13
PRODUCT SPECIFICATION SHEET 14
PRODUCT WARRANTY 15
3
APPEARANCE
4
MAIN PART
1: Saddle
2: Seat Post
3: Big Seat Post
4: Folding Lift Handle
5: Lock System
6: Supporting Post
7: Li-ion Battery
8: Rear Wheel
9: Kickstand
10: Controller
11: Arc Link
12: Top Four -bar link
13: Telescopic Link
14: Down Four-bar Link
15: DC Motor
16: Front Wheel
17: Quick release ①
18: Stem
19: Foldable Handlebar
20: Brake handle
5
SAFETY
1. The product is recommended for adults (18 years old and above) and is not
suitable for minors age (below 12 years old). Please do not load two
passengers at the same time.
2. Please wear your safety helmet and other protective equipment when
riding.
3. Do ride traffic lane and not pavement as it is breaking the local traffic rules
and regulations.
4. Please exercise in wide areas, and ride after skilled manipulation.
5. Do not attempt any dangerous actions like riding single-handedly.
6. Do not attempt to ride the bicycle on stairs that are above 10 cm. It may
result in vehicle overturn, causing injuries and/or damages to the rider
and/or bicycle.
7. The maximum speed limit for MOBOT ® 1 sec eBike is 25 Km/h. For your
safety, please maintain the riding speed at 20 Km/h.
8. When travelling at night, please limit the speed within 15 Km/h or less and
turn on the headlights.
9. For safety reasons, do not ride the bicycle in bad weather conditions such
as heavy downpours and high winds.
10. Do not use the bicycle when outdoor temperature is lower than 0ºC.
11. Please slow down or avoid using the bicycle when riding in poor road
conditions such as oily or slippery road surfaces.
12. Please adjust the handlebar according to your height to ensure a safe and
comfortable riding.
13. To avoid damages to the electrical parts of the vehicle, do not immerse the
bicycle in water with depth of more than 10 cm. Do not wash it with
pressurized water.
6
CLOSING STEPS
1): Folding process: hold ③and ⑥together with one hand, after clamping these together
③will slide down to the bottom, then lift ④up till you hear the “click” sound which
means that ⑤is in its locked position. Folding process is finished.
Attention: If ③is too tight to slide down, please give a pressure on the ①which will
help ③slide down to the bottom easier.
2): Unfolding process: lift the ①& ②up and lock in place at height required, then kick ⑨
back gently, the ebike frame will pull itself open. Pull up ①& ②again, making sure ⑥
is touching the head of the rear fork and you can’t see the round mark on the frame which
is covered by the bottom of ⑥
Attention: Before riding, you must check that ⑥has opened to its correct position so that
①& ②are stable, as well as the saddle & handle bar are locked at desired heights.
The number are according to the main part digrame.
Repeat the step backward to open the bicycle.
7
Circuit diagram of the 1 sec Fo ldi n g e-bike
ATTENTION TO DETAIL DURING RIDING &
ADJUSTMENT OF MAIN PARTS
During the pedal assist riding, there is no need to turn off the power switch, you may keep the
switch on. This will feel just like riding a normal bicycle.
8
1): Before riding, you can loosen the quick release ②, adjust the saddle height up or down for your
required fit, and then lock the quick release fastener ②.
2): Handlebar Adjustment
See in reference illustration A:
Insertion depth of the stem cannot be less than the minimum depth, to make sure that the safety line
on the stem is adjusted to be hidden.
Attention: During the adjustment of the handlebar stem up or down, please do not disconnect any plug
or electrical parts.
3): The throttle adjustment (for outside Europe Market)
The throttle is installed on the right handlebar; there is an on/off switch to turn power on & off.
After turning on the power button, you can use the throttle to accelerate or decelerate by rotating it or
release it to the top.
During you release the throttle, it will return back to its starting position, and accordingly you can turn
off the power button.
4): Front brake Adjustment
See in reference illustration B:
●Gap adjustment: let the single side touch, loosen the terminal screw a little, there are three holes on
the board, when moving up the spring, the elasticity will be raised to make the gap between brake and
rim become bigger and vice versa.
9
●The best gap between the brake shoes and the rim is 1.5mm.
●The best position of brake wire stand is that it not to touch the front mudguard.
5): Rear brake adjustment
See in reference illustration C and D，adjust for rear brake：
●Loose nut and pull-rod nut of the adjusting screw, unscrew the adjusting screw, while meantime,
hold the brake to make sure its position is on the1/3—1/2 of total distance in order the rear brake
shoe cling to the centre of the brake to reach ideal braking effect, and then screw down nut and the
pull-rod nut.
6): Wheel hub tightening Adjustment
When you tighten the wheel hub, the fasten torque should be as below:
●For front wheel hub, the fasten torque can not be less than 40-45 N.M
●For rear wheel hub, the fasten torque can not be less than 18-20 N.M
★Attention: Front wheel hub axle collets nut can not be over-tightened, otherwise it can cause warping
at the front wheel (not be smooth & round)
7): Adjustment of Chain（See picture E）
The chain may become loose after long-time riding, when you find this problem, you can unscrew the
nut of rear hub axle; tighten the chain adjustor for tightening the chain. Pull the chain down 10-15mm
to its best tension. Hold the pedal and rotate on anti-clockwise, the chain should be in normal state:
(rotate well, without abnormality, without noise). Tighten the screw of the rear hub axle again.
10
Table of contents
Other Mobot Bicycle manuals
