ML Accessories EAPIR1BK Instruction Manual

INSTALLATION & MAINTENANCE MANUAL

EAPIR1BK / EAPIR2BK

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid installation of the following products:

EAPIR1xx / EAPIR2xx

GENERAL INSTRUCTIONS

• This product must be installed in accordance with the latest edition of the IEE Wiring Regulations (BS7671)

and current Building Regulations. If in any doubt, consult a qualiﬁed electrician

• Please isolate mains prior to installation or maintenance

• Check the total load on the circuit (including when this luminaire is ﬁtted) does not exceed the rating of the

circuit cable, fuse or circuit breaker

• Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

• This product is Class II double insulated

• This product is IP44 rated

SAFETY

INSTALLATION

Note - Round cable should be used for the mains supply. The use of ﬂat cable will cause water ingress to the

ﬁtting.

• Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable IP

rated junction boxes should be used where required

• Separate the baseplate from the luminaire by removing the nuts on the front

• Using the baseplate as a template, mark the location for, and drill the ﬁxing holes ensuring not to infringe

with any gas/water pipes or electrical cables (see Fig. 1)

INSTALLATION & MAINTENANCE MANUAL

These instructions should be read carefully and retained after installation by the end user for future reference and

maintenance.

These instructions should be used to aid installation of the following products:

EAPIR1xx / EAPIR2xx

SAFETY

•This product must be installed in accordance with the latest edition of the IEE Wiring Regulations

(BS7671) and current Building Regulations. If in any doubt, consult a qualified electrician

•Please isolate mains prior to installation or maintenance

•Check the total load on the circuit (including when this luminaire is fitted) does not exceed the rating of the

circuit cable, fuse or circuit breaker

•Please note the IP (Ingress Protection) rating of this product when deciding the location for installation

•This product is Class II double insulated

•This product is IP44 rated

INSTALLATION

Note - Round cable should be used for the mains supply. The use of flat cable will cause water ingress to the fitting.

•Provide power to the required point of installation (refer to BS7671 for correct cabling methods). Suitable

IP rated junction boxes should be used where required

•Separate the baseplate from the luminaire by removing the nuts on the front

•Using the baseplate as a template, mark the location for, and drill the fixing holes ensuring not to infringe

with any gas/water pipes or electrical cables (see Fig. 1)

•Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the

surface using the plugs, screws and rubber washers provided

•Connect the luminaire to the mains supply ensuring the correct polarity is observed: Live (brown),

Neutral (blue)

•Ensuring the gasket on the baseplate is in place, align the luminaire with the baseplate and secure with

the two nuts

•Unscrew the bezel, insert a suitable LED lamp (5W max.) and carefully replace the bezel ensuring that the

seal is in place and not damaged. Note that the top and bottom bezels of the EAPIR2xx are not

interchangeable

•Push the PIR lid down to uncover the PIR adjustment dials (see Fig. 2)

•Turn the time setting to the minimum (anti-clockwise) and the lux setting to the maximum (clockwise)

•Switch on power to the luminaire and conduct a walk test – this is to check the area that the sensor is

detecting, and to adjust the detection settings as required

Fig. 1

• Feed the mains cable through the rubber grommet to retain IP rating, and secure the baseplate to the

surface using the plugs, screws and rubber washers provided

• Connect the luminaire to the mains supply ensuring the correct polarity is observed: Live (brown),

Neutral (blue)

• Ensuring the gasket on the baseplate is in place, align the luminaire with the baseplate and secure with the

two nuts

• Unscrew the bezel, insert a suitable LED lamp (5W max.) and carefully replace the bezel ensuring that

the seal is in place and not damaged. Note that the top and bottom bezels of the EAPIR2xx are not

interchangeable

• Push the PIR lid down to uncover the PIR adjustment dials (see Fig. 2)

• Turn the time setting to the minimum (anti-clockwise) and the lux setting to the maximum (clockwise)

• Switch on power to the luminaire and conduct a walk test – this is to check the area that the sensor is

detecting, and to adjust the detection settings as required

• Once the detection area is set, adjust the time and lux settings as required

• Check for correct operation

Fig. 2

•Once the detection area is set, adjust the time and lux settings as required

•Check for correct operation

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing.

Irreparable damage will occur if this instruction is not followed.

GENERAL

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not use

aggressive cleaning products or solvents which may damage the product.

Do not use any source of high-pressure washers to maintain or clean this luminaire.

This product is non-dimmable.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for

where facilities exist.

WARRANTY

This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with the

current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will invalidate

the warranty. If this product should fail within its warranty period, it should be returned to the place of purchase for a

free of charge replacement. ML Accessories does not accept responsibility for any installation costs associated with

the replacement product. Your statutory rights are not affected. ML Accessories reserve the right to alter product

specification without prior notice.

230V 50Hz, IP44, Class 2, NON-Dim

DCMAR22_V1

WARRANTY

This product has a warranty of 3 years from date of purchase. Failure to install this product in accordance with

the current edition of the IEE Wiring Regulations (BS7671), improper use, or removal of the batch code will

invalidate the warranty. If this product should fail within its warranty period, it should be returned to the place

of purchase for a free of charge replacement. ML Accessories does not accept responsibility for any installation

costs associated with the replacement product. Your statutory rights are not affected. ML Accessories reserve

the right to alter product speciﬁcation without prior notice.

GENERAL

Clean the external surfaces with a damp cloth using a mild solution of detergent and warm water only, do not

use aggressive cleaning products or solvents which may damage the product.

Do not use any source of high-pressure washers to maintain or clean this luminaire.

This product is non-dimmable.

This product should be recycled in the correct manner when it reaches the end of its life. Check local authorities

for where facilities exist.

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance

testing. Irreparable damage will occur if this instruction is not followed.

DCMAR22_V1

Supplied By:

(UK) Manufacturer

ML Accessories Ltd, Unit E Chiltern Park, Boscombe Road, Dunstable LU5 4LT,

www.mlaccessories.co.uk

(EU) Authorised Representative

nnuks Holding GmbH, Niederkasseler Lohweg 18,

40547 Düsseldorf, Germany,

Email: [email protected]om

This manual suits for next models

Table of contents

Other ML Accessories Lighting Equipment manuals

ML Accessories

ML Accessories SHE1BEMP Instruction Manual

ML Accessories

ML Accessories RWL2A Instruction Manual

ML Accessories

ML Accessories 5410A Instruction Manual

ML Accessories

ML Accessories Knightsbridge LEDFS12WW Instruction Manual

ML Accessories

ML Accessories SPIKE4BL Instruction Manual

ML Accessories

ML Accessories T8BLED15EM1 Instruction Manual

ML Accessories

ML Accessories AC65118 Instruction Manual

ML Accessories

ML Accessories EMKIT2 Instruction Manual

ML Accessories

ML Accessories AXREMC Instruction Manual

ML Accessories

ML Accessories LFC24B M Series Instruction Manual

ML Accessories

ML Accessories ENM5C Instruction Manual

ML Accessories

ML Accessories BATSCWMST4 Instruction Manual

ML Accessories

ML Accessories BT ACT Series Instruction Manual

ML Accessories

ML Accessories SURF236EMHF Instruction Manual

ML Accessories

ML Accessories SUR5LED Instruction Manual

ML Accessories

ML Accessories AMLEDB Instruction Manual

ML Accessories

ML Accessories WAD12AA Instruction Manual

ML Accessories

ML Accessories BATS2 Instruction Manual

ML Accessories

ML Accessories E27PR Instruction Manual

ML Accessories

ML Accessories LEDFRA6 Instruction Manual

ML Accessories

ML Accessories POTHB1 Instruction Manual

ML Accessories

ML Accessories T8BLED12 Instruction Manual

ML Accessories

ML Accessories FLP Series Instruction Manual

ML Accessories

ML Accessories WP15CTP Instruction Manual

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions