MIRKA PS 1437 Operating instructions

PS 1437

Service instructions v0314

Index. Page.

Index 2

Tool parts produced after 10/2013, from serial no: 201310 17823 3

Parts list after 10/2013, from serial no: 201310 17823 4

Tool parts produced before 09/2013, until serial no: 201308 17822 5

Parts list before 09/2013, until serial no: 201308 17822 6

Instructions.

Replacing the armature (50) in tool from serial no: 201310 17823 7-9

Replacing the armature (1) in tool up to serial no: 201310 17822 10

Identification by serial number and type 11

Exploded view for Polisher PS1437

Updated 11.12.2013

For tools produced after 10/2013, from serial no: 201310 17823

Parts list

Spare parts for PS1437 produced from 10/2013, from serial no: 201310 17823

Pos.

Code

Description

8991302111

Field

8991303111

Switch

8991304111

Strain relief

8991305111

Cable comp

8991306111

Locking Button

8991307111

Spring

8991308111

Locking Pin

8991309111

Screw

8991310111

Gear Housing

8991311111

Needle Bearing

8991312111

O-ring

8991313111

Distance ring

8991314111

Screw

8991318111

Ball Bearing

8991319111

Spring ring

8991320111

Cooling Fan

8991322111

Ball Bearing

8991323111

Rubber Sleeve

8991324111

Magnet Impulse ring

8991325111

Air Directing Ring

8991326111

Screw

8991331211

Cut Off Brush Kit (2 pcs)

8991332111

Brush Holder

8991333111

Motor Housing

8991334111

Protection Tube

8991335111

Electronic

8991336111

Screw

8991337111

Interference Filter

8991338111

Strain Relief Clamp

8991339111

Screw

8991340111

Rear Handle Kit

8991341111

Bail Grip

8991342111

Screw

8991343111

Side Handle

8991344111

Allen Key SW5

8991345111

Grease

8991350111

Armature

8991351111

Sleeve

8991352111

Distance Ring

8991353111

Pinion

8991354111

Seal

8991355111

Drive Shaft Comp

8991356111

Grease 24 g

Exploded view for Polisher PS1437

Updated 11.12.2013

For tools produced before 09/2013, until serial no: 201308 17822

Parts list

Spare parts for PS1437 produced before 09/2013, until serial no: 201308 17822

Pos.

Code

Description

8991301111

Armature

8991302111

Field

8991303111

Switch

8991304111

Strain relief

8991305111

Cable comp

8991306111

Locking Button

8991307111

Spring

8991308111

Locking Pin

8991309111

Screw

8991310111

Gear Housing

8991311111

Needle Bearing

8991312111

O-ring

8991313111

Distance ring

8991314111

Screw

8991315111

Drive Shaft Comp

8991316111

Sleeve

8991317111

Seal

8991318111

Ball Bearing

8991319111

Spring ring

8991320111

Cooling Fan

8991321111

Rubber Seal

8991322111

Ball Bearing

8991323111

Rubber Sleeve

8991324111

Magnet Impulse ring

8991325111

Air Directing Ring

8991326111

Screw

8991331211

Cut Off Brush Kit (2 pcs)

8991332111

Brush Holder

8991333111

Motor Housing

8991334111

Protection Tube

8991335111

Electronic

8991336111

Screw

8991337111

Interference Filter

8991338111

Strain Relief Clamp

8991339111

Screw

8991340111

Rear Handle Kit

8991341111

Bail Grip

8991342111

Screw

8991343111

Side Handle

8991344111

Allen Key SW5

8991345111

Grease 18 g

Replacing the armature (50) in tool from serial no: 201310 17823

Open screws (14) and lift off the drive shaft assembly (55)

Open screws (42) and remove the bail grip (41)

Open screws (9) and pull out the gear housing (10)

Pinion in the gear housing. Pinion tool to unscrew the pinion.

Tool: V7675 PE14-3A

Mirka code: 8995910611

Clamp the armature in a vice, protect the armature with a strip of soft material. Attach the

pinion tool as shown in the picture, and unscrew the pinion counter clockwise.

With the pinion (53) unscrewed pull the armature (50) out of the bearing. The bearing (18) is

locked in the gear housing (10) with a retaining ring (19).

Armature (50),Pininon (53),Retaining ring (19),Bearing (18),Seal (51),Distance ring (52).

Reassemble the parts in gear housing (10) and fill with new grease (24 g).

Open screws (36) to access the electrical parts.

Insert the armature halfway in to the motor housing (33), lift the brushes with a screwdriver

to get the collector in correct position.

Collector in correct position, carbon brush in contact with the collector. Tighten the gear

housing (10) to motor housing (33), and mount the drive shaft assembly (55) to the gear

housing (10).

Replacing the armature (1) in tool up to serial no: 201308 17822

Open the gear housing as decribed on page 7. Clamp the armature in a vice, protect the

armature with a strip of soft material. Use two screwdrivers to keep the sleeve (16) against

the housing, and turn the housing counter clockwise to unscrew the sleeve.

Armature (1), Sleeve (16), Retaining ring (19), Bearing (18), Seal (17).

Reassemble the parts in gear housing (10) and fill with new grease (18 g).

Assemble the tool as described on page 9.

Other manuals for PS 1437

This manual suits for next models

Popular Sander manuals by other brands

Oliver

Oliver 6305 owner's manual

Jet

Jet 22-44 Pro-3 Operating instructions and parts manual

Makita

Makita M9204 technical information

Makita

Makita M9204 instruction manual

Craftsman

Craftsman 351.215131 Operator's manual

Clarke

Clarke Woodworker CBS1-5B Operation & maintenance instructions

Chicago Pneumatic

Chicago Pneumatic CP9778 Operator's manual

Nitto Kohki

Nitto Kohki BB-20 instruction manual

Ferm

Ferm FEOS-135 user manual

Unior

Unior 1510 Operating instruction

stayer

stayer ls1200 operating instructions

Jet

Jet JSG-96 Operating instructions and parts manual

Parkside

Parkside PDS 290 B2 Operation and safety notes

Status

Status XPA Series Original instructions

Clarke

Clarke EZ Sand Operator's manual

Craftsman

Craftsman 113.22521 owner's manual

Craftsman

Craftsman 113.225831 owner's manual

CLAS

CLAS OP 1429 manual