Mircom MPS-800MP Series User manual

www.mircomgroup.com LT-6168 Rev. 0 Oct 2021

MPS-800MP(U) Series

Fire Alarm Manual Station

Mircom’s MPS-800MP(U) Series Fire Alarm Manual Stations

provide manual fire alarm activation.

This guide covers these models:

MPS-810MP Single Stage, Dual Action, MP Addressable Manual

Station

MPS-810MPU Single Stage, Dual Action, MP Addressable

Manual Station (US)

MPS-802MP Two Stage, Dual Action, MP Addressable Manual

Station

MPS-822MP Two Stage, Dual Action, MP Addressable Manual

Station with additional door contacts

Specifications & Dimensions

Compatible with FX-400 series and FleX-Net™ FX-4000 Fire

Alarm Control Panels

Electrical Rating:

Nominal Operating Voltage: 15-30 VDC

Maximum alarm current: 3.3 mA

Standby current: 2 mA

Electrical Rating for MPS-822MP maglock terminal:

1A at 30VDC

Dimensions:

139 mm H x 104 mm W x 34 mm D

(5 1/2” H x 4 1/8” W x 1 3/8” D)

Install the manual station

Contents of kit

MPS-810MP(U): 2 mounting screws, 2 reset keys (black)

MPS-802MP and MPS-822MP: 2 mounting screws, 2 reset keys

(black), 2 stage two keys

A. Open

1. Insert the reset key into the reset keyhole and turn it.

2. Pull the cover open.

Figure 1 Front of manual station

Figure 2 Opening the station

Notes

• Environment: Indoor, dry

• Do not change factory applied finishes.

• Wire as shown so that supervision of connections is

maintained.

• Maximum wire size: 14 AWG

• ADA compliant.

• To be installed per ADA 4.27.1 to 4.27.4 inclusive.

• Wiring must be in accordance with CSA C22.1, Canadian

Electrical Code, Part I, Safety Standard for Electrical

Installations, Section 32 and CAN/ULC-S524, Standard for

Installation of Fire Alarm Systems.

• All manual fire alarm stations shall be installed as per the

specific requirements outlined in the UL/ULC codes, as well

as all other applicable national or local codes. Final

acceptance is subject to the local authority having

jurisdiction.

RESET KEYHOLE

STAGE TWO

KEYHOLE (MPS-802MP

ND MPS-822MP)

PUSH BAR

PULL HANDLE

LED FLASHES RED

WHEN POLLING AND IS

STEADY RED IN ALARM

COVER

MOUNTING

PLATE

Canada

25 Interchange Way

Vaughan, ON L4K 5W3

Tel: 1-888-647-2665

U.S.A

4575 Witmer Industrial Estates

Niagara Falls, NY 14305

Tel: 1-888-647-2665

MPS-800MP(U) Series

Fire Alarm Manual Station

www.mircomgroup.com LT-6168 Rev. 0 Oct 2021

B. Wire

Note: The maximum wire size is 14 AWG.

1. Strip wires to 10 mm (25/64”) maximum.

2. Push the wire into the terminal.

Note: The terminals have a push-in lock. To remove the wire,

push the terminal in with the screwdriver and pull out the

wire at the same time. see Figure 3.

Figure 3 Removing the wire

3. Wire as shown in Figure 4.

Figure 4 Wiring

C. Mount

Flush mount indoor: Single-gang electrical box.

Surface mount indoor: BB-800 backbox with or without STI-1230

(Deep Cover without Gasket)

Note: Mount the manual station with the Mircom logo on the

bottom.

Figure 5 Back of manual station

D. Set the addressable module

Follow the instructions in LT-6146, the MIX-4090 Device

Programmer Installation Manual, available on

http://www.mircom.com.

The factory default address is 255.

The connector for the device programmer is inside the unit above

the addressable module, as shown in Figure 6.

Figure 6 Connector for device programmer

Using the manual station

Activate the alarm

1. Push in the push bar.

2. Pull down the pull handle.

A qualified person must reset the station by opening it with the

reset key. See Resetting the manual station below.

Activate the stage two alarm (MPS-802MP and

MPS-822MP)

• Insert the stage two key into the stage two keyhole, and then

turn the key.

The stage two alarm activates immediately.

Note: The stage two alarm will activate automatically a certain

amount of time after the handle has been pulled if no

action is taken. This time is set in the Fire Alarm Control

Panel.

Reset the manual station

Note: Resetting the station does not cancel the alarm at the

panel.

1. Insert the reset key into the reset keyhole and turn it.

2. Pull the cover open. The switch is now reset.

3. Close and lock the station with the reset key.

4. Reset the Fire Alarm Control Panel to reset the alarm.

TO REMOVE WIRE, PLACE

A SMALL FLATHEAD

SCREWDRIVER INTO THE

GROOVE AND PUSH IN.

AT THE SAME TIME, PULL

THE WIRE OUT OF THE

TERMINAL.

TO NEXT STATION OR

LEAVE IT EMPTY

FROM

STATION

TO MAGLOCK

(MPS-822MP)

MOUNTING

HOLES

CONNECTOR

FOR DEVICE

PROGRAMMER

Other Mircom Fire Alarm manuals

Mircom

Mircom FX-350 Series User manual

Mircom

Mircom FA-102T User manual

Mircom

Mircom RAM-300LCD Series User manual

Mircom

Mircom MS-700ID SERIES User manual

Mircom

Mircom MS-400MP Series User manual

Mircom

Mircom FleXNet FNC-2000 User manual

Mircom

Mircom MPS-800MP Series User manual

Mircom

Mircom FleX-Net FX-4000 User manual

Mircom

Mircom FleX-Net FX-2003-12NDS User manual

Mircom

Mircom MPS-800MPU Series User manual

Mircom

Mircom MS-700AP Series User manual

Mircom

Mircom MPS-800 Series User manual

Mircom

Mircom QX-mini User manual

Mircom

Mircom FleX-Net BBX-1024DS User guide

Mircom

Mircom RAM-300LCD Series User manual

Mircom

Mircom FA-1000 SERIES User manual

Mircom

Mircom FX-350 Series User manual

Mircom

Mircom flexnet User manual

Popular Fire Alarm manuals by other brands

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 installation manual

System Sensor

System Sensor 22051TLE-RF-26 Installation and maintenance instructions

Pittway

Pittway Notifier AM2020 troubleshooting guide

Ampac

Ampac ZoneSense user manual

Kidde

Kidde VM-1 Technical reference manual

LST

LST SIM016-3 Specification sheet

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Owner's Manual & Installation Instructions

bolid

bolid S2000-IP-03 instruction manual

GST

GST DI-9204 Installation

E2S

E2S BExTBG05D instruction manual

Notifier

Notifier UZC-256 installation manual

Fire-Lite Alarms

Fire-Lite Alarms MS-2 instructions

Siemens

Siemens FDOOT221 Technical manual

hyfire

hyfire HY5000 Series install guide

FlameStop

FlameStop PFSIFP8 Installation and operation manual

Radionics

Radionics Radionics 9124 user guide

UniPOS

UniPOS FD 7120 instruction manual

FIREWOLF

FIREWOLF FW-C01224 owner's manual