MILLASUR Anova BIO70D Specification sheet
BIO70D / BIO150D
English
SHREDDER
INSTRUCTIONS FOR USE AND MAINTENANCE
Technical data
3
G. On/Off Switch H. Throttle
2400/min
Ignition system
1.1L
Blade speed
212cc
E. Primer
manual and electric
Engine speed
Unleaded petrol
b.engine
Model
oil volume
Displacement
Illustration 1. Identification of the components of the shredder
I. Fuel Tank Cap J. Air Filter
Identification of
OHV 4-stroke
Type of motor
machine components (Illustration 1)
F. Fuel Cock
89mm
7HP/3600rpm
3.6L
76mm
C. Chip discharge D. Funnel
crushing capacity
Fuel type
A. Hopper
420cc
fuel volume 6.5L
Illustration 1
Manual
maximum power
K.
Exhaust
L. Pull Starter
0.6L
15HP / 3600rpm
3600rpm
EN
BIO150DBIO70D
Identification of machine components
Indicates a potentially hazardous situation which, if not
avoided, will WARNING
Safety instructions for machinery
ATTENTION
For your own safety, read the instruction manual
DANGER
CAUTION
before using this machine
CAVEAT
4
CAVEAT
EN
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
machinery can cause permanent hearing loss.
MACHINE. Wood dust is carcinogenic, that is, it can cause cancer and severe
respiratory
diseases.
4. ALWAYS WEAR HEARING PROTECTION WHEN OPERATING THE MACHINE. the noise of the
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
1. READ THE MANUAL IN ITS ENTIRETY BEFORE STARTING THE MACHINE. Machine
5. WEAR APPROPRIATE CLOTHING. DO NOT wear loose clothing, gloves, a tie, rings or
jewelry that can be caught in moving parts. If you have long hair, cover it with something
presents risks of serious injury to untrained users.
2. ALWAYS WEAR ANSI APPROVED SAFETY GLASSES WHEN
protection element and wear non-slip shoes.
6. REFRAIN FROM OPERATING THE MACHINE IF YOU ARE TIRED, UNDER THE INFLUENCE
OPERATE THE MACHINE. Normal glasses only have impact resistant lenses. Are not
MAY cause minor or moderate injury. It can also be used to
warn against unsafe practices.
safety glasses.
OF ALCOHOL, DRUGS OR MEDICATION. Be mentally alert at all times.
3. ALWAYS WEAR AN ANSI APPROVED RESPIRATOR WHEN OPERATING THE
The purpose of safety symbols is to draw your attention to potentially dangerous situations. This
manual uses a series of symbols and verbal indications that are intended to convey the level of
importance of the safety messages. The progression of the symbols is described below. Remember
that safety messages by themselves do not eliminate hazards and are not a substitute for correct
accident protection measures.
This symbol is used to alert the user to useful information on the
correct operation of the machine.
SECTION 1: SAFETY
EN
5
13. USE A GROUNDED EXTENSION CORD WITH THE CORRECT AMPERAGE FOR THE
MACHINE. Underpowered cables overheat and lose power.
11. DO NOT USE IN HAZARDOUS
ENVIRONMENTS
12. KEEP WORK AREA CLEAN AND WELL LIGHTED. Clutter and dark areas can lead to
accidents.
20. DO NOT FORCE MACHINERY. Work at the speed for which the machine or attachment
is
designed.
Replace extensions if damaged. DO NOT use extension cords for 220V machinery.
21. SECURE THE PIECE. Use clamps or a vise to hold the part when practical. A secure
piece protects your hands and frees them to operate the machine.
14. ALWAYS DISCONNECT THE MACHINE FROM THE POWER OUTLET
BEFORE
CARRYING OUT MAINTENANCE. Check that the switch is in the OFF position before
reconnecting.
22. DO NOT STRETCH YOUR BODY. Always maintain a firm posture and balance.
23. MANY MACHINES WILL EJECT THE PART TOWARDS THE OPERATOR.
Be
aware of and avoid conditions that cause part kickback.
15. ALWAYS SUBJECT THE MACHINE TO A GOOD MAINTENANCE. Keep blades
sharp
and clean for safer and more efficient performance. Follow the instructions for lubricating and
changing accessories.
7. THE MACHINE SHALL ONLY BE OPERATED BY TRAINED AND
PROPERLY
SUPERVISED PERSONNEL. Make sure that the safety instructions are well understood
and guaranteed.
16. CHECK THAT GUARDS ARE IN PLACE AND OPERATE PROPERLY
BEFORE
USING MACHINERY.
24. ALWAYS ATTACH MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.
8. KEEP CHILDREN AND THIRD PARTIES AWAY FROM THE MACHINE. Children
and
visitors must remain a safe distance from the work area.
17. REMOVE ADJUSTMENT AND SPANNER WRENCHES. Always check the
adjusting
wrenches and wrenches before starting the machine.
25. BE AWARE THAT CERTAIN WOODS MAY CAUSE AN ALLERGIC REACTION
in
people and animals, especially if exposed to fine dust.
10. NEVER LEAVE A MACHINE ON. Press the OFF switch and wait for the machine to
come
to a complete stop before leaving the machine unattended.
9. WORKSHOP MUST BE CHILDPROOF. Use padlocks, master switches, and
remove
keys from ignition switches.
18. BEFORE USING THE MACHINERY, CHECK FOR DAMAGED PARTS.
Check the type of wood dust you will be exposed to and always wear an approved respirator.
19. USE THE RECOMMENDED ACCESSORIES. See the instruction manual for more
information
on recommended accessories. The use of inappropriate accessories may cause risk of injury.
Check the fastening and alignment of the parts, that none of them are broken, the assembly
of the
parts, that the bolts are tight and all the aspects that can affect the operation of the machine.
Repair or replace affected parts.
6
1. READ THIS MANUAL AND THE ENGINE MANUAL IN ITS ENTIRETY. These manuals contain
instructions for the safety and proper use of this wood chipper.
9. MATERIAL FEEDING. Do not hold tight to branches or bushes and let the machine drag
the
material. The machine sometimes drags the material very quickly and can drag your hand if you
are gripping the material tightly. If the blades hit a hard object if the machine starts to vibrate or
make a strange noise, turn off the power immediately.
6. WORKPLACE. Place the shredder on a firm, flat surface of grass or earth. DO NOT
place
the chipper on gravel, asphalt, concrete or stone. Chips are thrown with enough force to
ricochet off hard surfaces and cause serious injury. DO NOT locate the machine where sparks or
heat from the engine could cause a fire.
2. SAFETY EQUIPMENT. Wear safety glasses, hearing protection and gloves when working
with
the chipper. Check that the people around you are also wearing safety equipment.
10. SWITCHING OFF THE SHREDDER. Shut off machine, wait for all moving parts to
stop,
and disconnect spark plug wire before moving machine, emptying bag, unclogging intake or
discharge lines, filling fuel tank, or making any repairs or maintenance task.
7. SOLID FOUNDATION. Placing the shredder on a slope or slippery surface may cause
the
operator to fall and strike the machine, which could result in motor burns or amputations if their arm
gets stuck in the chute.
3. ENGINE OPERATION. Consult the engine manual for information on handling and
safety
guidelines applicable to a gasoline engine.
11. START-UP OF THE BIO-SHREDDER. Check that the hopper and funnel are empty
when
you turn on the machine. The starter rope may stop suddenly, causing the machine to tip over
or injuring your hand.
Wear closed, non-slip shoes to ensure a firm footing.
4. HAND PROTECTION. DO NOT put your hands or any other part of your body into
the
hopper, funnel, or spout while the blades are rotating. The chipper can pull you into the blades
causing amputations. To avoid burns, DO NOT touch the exhaust pipe while the machine is
running or immediately after it is turned off.
12. CLEANING OF THE SHREDDER. Wait for the engine to cool down. Then remove
the
accumulation of dust and sawdust from the motor with a brush to avoid overheating or fire.
8. JAMS AND JAMS. Shut off the chipper, wait for all moving parts to stop, and
disconnect
the spark plug wire before attempting to clear binding or jam.
5. APPAREL. Do not wear loose clothing, ties, scarves, or jewelry that could get caught in
moving
parts. DO NOT wear clothing or gloves with straps or clip-ons. These types of garments can
become entangled with the material to be shredded, trapping it in the shredder.
EN
CAVEAT
Additional Safety Instructions for Wood Chippers
SECTION 2: ASSEMBLY
A list of safety guidelines cannot cover all contingencies. Every environment is
different. Always give priority to safety as this affects your own working conditions.
Use this machine and any other with respect and caution. Failure to do so could
result in serious injury, equipment damage, or performance degradation.
clearances
The machine presents serious safety risks if handled by untrained personnel. Read
this manual completely and carefully to familiarize yourself with the controls and
operations before starting it up.
Take into account the length of the material to be shredded in the machine and check
that the height of the place is sufficient to accommodate the material. Make sure the unit
is close to the area where the chips will be used to save transportation.
machine or a distraction. Use the machine with respect and caution to reduce the
possibility of an accident to the operator. Failure to follow normal safety precautions
can result in serious injury.
The shredder should be located on a flat, smooth grass or dirt surface to prevent it from
tipping over. DO NOT place the machine on a concrete, asphalt, or other hard material
surface. Chips can bounce off a hard surface and cause injury.
Location
As with any machine, there is a potential risk when working with it. Accidents are
often the result of poor knowledge of the
Stay away from the unloading area. Check that there are no third parties, especially
children, animals or objects that could be damaged or that you do not want to see covered
with chips in the discharge area.
EN
7
CAVEAT
CAUTION
CAVEAT
Siting Considerations
Mounting Safety
Paw
leg screws
Wheel
support bolts
2. Attach the wheels and legs with the bolts removed in Step 1.
The main components of this wood chipper have been assembled at the factory. It is only
necessary to assemble a few small elements. All parts and material listed in the inventory will be
used in the assembly process.
Figure 2. Leg placement
Illustration 2
Figure 3. Hopper Gasket Placement
4. Place hopper over gasket and line up all holes. Secure it with screws
lay the shredder down with full fuel and oil tanks and it would spill.
Illustration 3
3. Stand the shredder upright and fit the hopper gasket around the shredder.
1. Lay the shredder down and remove the four bolts indicated in illustration 2. DO NOT
hopper as indicated in illustration 3.
hexes and lock nuts. (See Illustration 4).
DO NOT start the machine until you have assembled all of its parts. Failure to do so could
result in serious injury or major machine damage.
To assemble the shredder:
EN
8
Mounting
EN
6. Place the funnel over the studs on the side of the shredder and secure using washers and locknuts (See
Illustration 6).
Illustration 4
Illustration 6
Illustration 4. Securing the hopper
Figure 5
Figure 6. Funnel Installation
5. Place handle on hopper and line up all holes. Secure using washers and bolts. (See illustration 5).
Figure 5. Installing the handle
7. If it includes a trailer hitch. Place a tow bar head on the
9
10
ATTENTION
EN
Filling the fuel tank
The wood chipper is powered by a four-stroke engine powered by unleaded gasoline. Use a suitable funnel to
transfer the fuel to the tank avoiding any spillage or overfilling. The fuel tank should not be filled above the fuel filter.
This wood chipper is not delivered with oil in the engine. Add oil before starting or the engine will seize.
fuel as indicated in Figure 10.
Filling engine oil
Figure 10
Place the machine on a flat surface and remove the oil filter cap (Illustration 8)(8.1)
wheel clamping system and align the hole. Insert the fixed pin and secure it with a pin (see
illustration 7).
Illustration 8
Illustration 7
Illustration 9
8. Before working with the machine, fill the engine with gasoline and oil according to the
Figure 7. Attaching the tow rod
Fill engine oil up to the upper level of the dipstick (Illustration 9)
instructions.
(9.1)
This manual suits for next models
1
Table of contents
Popular Paper Shredder manuals by other brands
Swingline
Swingline STACK-AND-SHRED200X&200XL 60X Start here
GBC
GBC ShredMaster CC055 instruction manual
UNITED OFFICE
UNITED OFFICE UAV 190 A1 operating instructions
UNITED OFFICE
UNITED OFFICE UAV 190 A1 operating instructions
Rexel
Rexel Optimum AutoFeed+ 45X instruction manual
Martin Yale
Martin Yale 227284S1 instruction manual
