Miles Industries GV60 Instruction Manual
1
Operation Modes
man MAN MODE—Manual Mode. The flame height can be adjusted in the following
manners:
Press the ▲ (up) button to turn on the main burner.
Press the ▲ (up) button to increase the flame height.
Press the ▼ (down) button to decrease the flame height or to go to pilot Standby
position.
For fine adjustments, tap the ▲ and ▼ buttons.
NOTE: While pressing either button, a symbol indicating transmission appears on the
upper right hand corner of the display. The receiver confirms transmission with an
acoustic signal.
STANDBY MODE—Ignited pilot only.
☼temp TEMP MODE—Daytime Temperature Mode (appliance must be in Standby
mode; pilot ignited): The room temperature is measured and compared to the set
temperature. The flame height is then automatically adjusted to achieve the Daytime
set temperature.
☽temp TEMP MODE—Nighttime Setback Temperature Mode (appliance must be
in Standby mode, pilot ignited): The room temperature is measured and compared to the
Nighttime Setback temperature. The ame height is then automatically adjusted to achieve the
Nighttime Setback temperature.
timer TIMER MODE—(appliance must be in Standby mode, pilot ignited): The Timer setting
allows you to set two burner ON times and two burner OFF times for every 24-hour period.
1.
2.
3.
GV60 Remote Control Operation
Your replace remote control helps you get the comfort, convenience and aesthetics you want from your gas replace.
The remote controls your replace in different ways.
IMPORTANT: BEFORE YOU BEGIN, please note that on this system, the settings of time, temperature and automatic
ON/OFF can only be programmed when the function display is ashing. Be patient when programming as it can take
a few seconds to set.
Changing the Mode of Operation
Briefly pressing the SET button changes the mode of operation in the following order:
man→ ☼temp → ☽temp → timer →and back to man.
NOTE: MAN mode can also be reached by pressing either the ▲ or ▼ buttons.
In TEMP mode,
☼ indicates the daytime temperature setting.
☽ indicates the nighttime temperature setting.
In TIMER mode,
☼ indicates the start time setting.
☽ indicates the stop time setting.
2
Time
To set the time, follow the steps below.
The display indicates °C/24-hour or °F/12-hour clock. To change from one to the other,
press and hold both the OFF and ▼ buttons until the display changes.
To set the time, hold down both the ▲ and ▼ buttons until the display ashes. Let go.
Quickly press the ▲ button to set the hour and the ▼ button to set the minutes.
Note: You must start setting the time while the display is ashing. If it stops ashing, go
back to 2.
Press the OFF button to return to manual mode or simply wait and it will automatically
return to Manual mode.
1.
2.
3.
4.
Use this setting when you come in and want to enjoy a set temperature.
Select either the ☼temp MODE or the ☽temp MODE by briefly pressing the SET button.
Hold the SET button until the TEMP display flashes.
Set the desired temperature with the ▲ or the ▼ buttons.
Note: 4.5°C/40°F is the minimum temperature setting.
Press the OFF button or simply wait and the display will go to the temperature control
mode.
Note: If you would like the Nighttime Setback temperature control to turn off, decrease the
☽temp MODE setting until [---] appears on the display.
Your replace will reach the set temperatures and the remote handset will check the
temperature every ve minutes, adjusting the amount of fuel needed to give you a steady,
even heat.
The display must remain in TEMP mode on the remote handset.
1.
2.
3.
4.
5.
Temperature
Flame Height
In Standby mode, press the ▲ button to increase the flame height.
Press the ▼ button to decrease the flame height or to set the appliance at the pilot flame.
For fine adjustments, tap the ▲/▼ buttons.
1.
2.
3
Low Battery Indication
Remote handset: BATT will appear on the display when the battery needs to be replaced.
Replace with one 9 V battery (alkaline recommended).
Receiver: Three short ‘beeps’ will sound when the motor turns when the batteries need to be
replaced. Replace with four 1.5 V batteries (alkaline recommended).
Automatic Standby Mode
If there is no transmission from the handset to the receiver within a 6-hour period, the
appliance will go to STANDBY (pilot) mode.
Handset / Receiver Match
The remote control handset and receiver are programmed to function together. In case of a
replacement of the handset or the receiver, you will need to reset the control valve to allow
them to function together. Contact your dealer for details
Timer
It is possible to program two periods of time per day at which your replace will turn on and off
automatically.
For example, you can set your replace to turn on in the morning just before you get up (P1 ☼
[start time]) and to turn off when you leave for the day (P1 ☽ [stop time]). Then, you can set
your replace to turn on again at the end of the day (P2 ☼[start time]) and to turn off when
you go to bed at night (P2 ☽ [stop time]).
If you wish to set only one time period at which your replace will turn on and off, program P2
☼[start time] and P2 ☽ [stop time] for the same time as P1 ☽ [stop time].
Select TIMER mode by briefly pressing the SET button.
Press and hold the SET button until TIMER is displayed on the lower right hand side.
Press and hold the SET button until P1 ☼ and the time display flashes. Set the start time
by pressing the ▲ button for the hour and the ▼ button for the minutes. Then, briefly
press SET to P1 ☽ and set the stop time in the same manner you just set P1 ☼.
Briefly press the SET button again for the next burner cycle time, which will be P2 ☼and
P2 ☽.
Once all four times are set, press OFF or simply wait to complete programming.
The remote handset must remain in TIMER mode to function automatically.
1.
2.
3.
4.
5.
6.
Table of contents
Other Miles Industries Remote Control manuals
