MikroElektronika Ambient 2 click User manual

2 3

click

BOARD™

www.mikroe.com

2. Soldering the headers

3. Plugging the board in

Once you have soldered the headers your

board is ready to be placed into the desired

mikroBUS™socket. Make sure to align the cut

in the lower-right part of the board with the

markings on the silkscreen at the mikroBUS™

socket. If all the pins are aligned

correctly, push the board all the

way into the socket.

Turn the board upward again. Make sure

to align the headers so that they are

perpendicular to the board, then solder the

pins carefully.

Turn the board upside down so that

the bottom side is facing you upwards.

Place shorter pins of the header into the

appropriate soldering pads.

Before using your click board™, make sure

to solder 1x8 male headers to both left and

right side of the board. Two 1x8 male headers

are included with the board in the package.

4. Essential features

The measurement range of Ambient 2 click

is from 0.01 Lux to 83k lux, and a 23-bit

resolution. The device lters out 99% of the

infrared light spectrum, which isn’t visible

to the human eye. Therefore it’s suitable for

systems that create lighting experiences,

such as display backlights, automated room

lighting and similar. The optical surface of

the sensor should kept clean, but the sensor

is not overly sensitive to micro shadows cast

by intruding particles.

Ambient 2 click carries TI’s OPT3001

ambient light sensor. It’s a single-chip

lux meter that measures only the visible

part of the light spectrum (mimicking

the human eye’s response to light). The

board communicates with the target MCU

through mikroBUS™I2C pins (SCL, SDA),

as well as through an interrupt pin (INT).

The board is designed to use a 3.3V power

supply only.

Ambient 2 click

1. Introduction

Ambient 2 click manual

ver 1.00

0100000080269

RST

SCK

MOSI

MISO

+3.3V

GND

PWM

INT

SCL

SDA

+5V

GND

MIKROBUS

DEVICE

CONN.

VCC-3V3VCC-3V3

2K2

PWR

SCL 4

INT 5

ADD

GND

SDA 6

VDD

OPT3001

4K7

SDA

INT

SCL

VCC-3V3VCC-3V3VCC-3V3

INT

SCL

SDA

VCC-3V3

ADD

100nF

VCC-3V3

ADD

SDA

SCL

8. Code examples

MikroElektronika oers free tech support

(www.mikroe.com/support) until the end of

the product’s lifetime, so if something goes

wrong, we’re ready and willing to help!

Once you have done all the necessary

preparations, it’s time to get your click board™

up and running. We have provided examples

for mikroC™, mikroBasic™and mikroPascal™

compilers on our Libstock website. Just

download them and you are ready to start.

.com

6. Dimensions

MikroElektronika assumes no responsibility

or liability for any errors or inaccuracies

that may appear in the present document.

Specication and information contained in

the present schematic are subject to change

at any time without notice.

mm mils

LENGTH 28.6 1125

WIDTH 25.4 1000

HEIGHT* 3.3 130

5. Schematic

7. SMD jumpers 10. Disclaimer

9. Support

25.4 mm / 1000 mils

28.6 mm / 1125 mils

Ambient 2

click features

four jumpers

for specifying

the I2C

address.

* without headers

This manual suits for next models

Other mikroElektronika Microcontroller manuals

mikroElektronika

mikroElektronika Touchpad click User manual

mikroElektronika

mikroElektronika CLICKER 2 PIC32MZ User manual

mikroElektronika

mikroElektronika Click User manual

mikroElektronika

mikroElektronika EasyPIC Fusion V7 TQFP PT MCU CARD 1 User manual

mikroElektronika

mikroElektronika mikromedia for ARM User manual

mikroElektronika

mikroElektronika SmartGM862 User manual

mikroElektronika

mikroElektronika CLICKER 2 FOR FT90X User manual

mikroElektronika

mikroElektronika mikromedia PIC32 User manual

mikroElektronika

mikroElektronika BIGdsPIC6 User manual

mikroElektronika

mikroElektronika UNIQUE ID click User manual

mikroElektronika

mikroElektronika Easypic Fusion PIC32MX460F512L User manual

mikroElektronika

mikroElektronika Mikromedia MIKROE-608 User manual

mikroElektronika

mikroElektronika MIKROE-1993 User manual

mikroElektronika

mikroElektronika ROTARY R click User manual

mikroElektronika

mikroElektronika MINI-M4 User manual

mikroElektronika

mikroElektronika dsPIC Ready3 User manual

mikroElektronika

mikroElektronika Ready for XMEGA User manual

mikroElektronika

mikroElektronika UNI-DS3 User manual

mikroElektronika

mikroElektronika MSP432 clicker User manual

mikroElektronika

mikroElektronika click BOARD Comparator click User manual

mikroElektronika

mikroElektronika mikromedia for STM32 User manual

mikroElektronika

mikroElektronika Mikromedia PIC24EP User manual

mikroElektronika

mikroElektronika CLICKER2 FOR PIC32MX User manual

mikroElektronika

mikroElektronika ROTARY Y click User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide

mikroElektronika Ambient 2 click User manual

Popular Microcontroller manuals by other brands