Miele W 1753 User manual

Installation Instructions

W 1753HQ&$



,QVWDOODWLRQUHSDLUDQGPDLQWHQDQFHZRUNVKRXOGEHSHUIRUPHGE\

D0LHOHDXWKRUL]HGVHUYLFHWHFKQLFLDQLQDFFRUGDQFHZLWKQDWLRQDO

DQGORFDOVDIHW\UHJXODWLRQVDQGWKHSURYLGHGLQVWDOODWLRQLQVWUXFWLRQV

Front view

aInlet hose for hot water

bInlet hose for tap water (cold)

cPower cord

d-gDrain hose (with detachable

swivel elbow)

hDetergent dispenser drawer

iControl panel

jLoading door

kAccess to drain filter, drain pump,

and emergency door release

nFour height-adjustable feet

Installation and connection

Rear view

aProtruding lid to grip when moving

the washer

bPower cord

cInlet hose for tap water (cold)

dInlet hose for hot water

eDrain hose

fTransport clip for inlet and drain

hoses

gSafety cap for transit bars

hTransport clip for inlet and drain

hoses and for storing transit bars

when not in use.

Installation and connection

Installation surface

A concrete floor is the most suitable

installation surface for a washing

machine, being far less prone to

vibration during the spin cycle than

wooden floorboards or a carpeted

surface.

Please note:

^The machine must be level and

securely positioned.

^To avoid vibrations during spinning,

the machine should not be installed

on soft floor coverings.

If installing on a wooden joist floor:

^We recommend a plywood base (at

least 59x52x3 cm). The base should

span several joists and be bolted to

the joists and not only to the

floorboards. Check for the presence

of pipes and cables first.

If possible, install the machine in a

corner, as this is usually the most stable

part of the floor.

,If the machine is installed on a

raised plinth, it has to be secured

against slippage during spin using

retaining clips (available from the

Miele Spare Parts Dept). Otherwise

there is the danger of the machine

moving about and falling off the

plinth.

Transporting the washing machine to

its installation site

To manoeuvre the machine out of its

packing case to its installation site hold

it by the edge of the lid where it

protrudes to the rear of the washing

machine as well as by the front feet.

,Ensure that the machine feet and

the floor are dry to prevent the

machine from slipping during the

spin cycle.

Removing the transit bars

^To remove the left and right covers

1. Pull on the attached stopper,

2. then use a screwdriver to release the

catch at the top.

Installation and connection

^Using the spanner supplied, turn the

left-hand transit bar 90°, then

^withdraw the transit bar.

^Turn the right-hand transit bar 90°,

then

^withdraw the transit bar.

Installation and connection

,To avoid the risk of injury the

holes for the transit bars must be

covered after the transit bars have

been removed.

^Plug the holes with the plastic caps

as illustrated.

^Secure the transit bars to the back of

the washing machine. Make sure that

the top catch is located above the

holder.

,The machine must not be moved

without the transit bars in place.

Store them as shown or keep them

in a safe place for future use. They

must be re-fitted if the machine is to

be moved again (e.g. when moving

house).

Re-fitting the transit bars

Re-fitting is carried out by reversing the

procedure.

Installation and connection

Levelling the machine

To ensure safe and proper operation,

the washer must stand perfectly level

on all four feet.

Improper footing may increase water

and power consumption, and may

cause the washer to wander across the

floor.

Screw out and adjust the feet

Use the four adjustable feet to level the

washer. The washer is delivered with all

four feet in the shortest (screwed in)

position.

^Use the combination wrench

provided to turn the counternut 2

counterclockwise. Then turn the

counter nut 2together with the foot 1

to unscrew.

^Use a level to check that the washer

is standing square.

^Hold the foot 1securely with a pipe

wrench. Now use the combination

wrench to screw the counternut 2

firmly back up against the housing.

,All four counternuts must be

tightened firmly up against the

housing. Be sure to also check this

on the feet that did not require

levelling. Otherwise, the washer may

wander about.

Installation and connection

Installing under a countertop

,The washer lid must NOT be

removed.

Provided the workspace is high

enough, the washer can be pushed

under a countertop with the lid in place.

Washer-dryer stack

The washer can be stacked with a

Miele tumble dryer. A stacking kit will

"WTV 414", be required and can be

obtained through your Miele dealer or

Miele Customer Service.

Please note:

aSafety clearance to wall:

at least 2 cm

bHeight:

Stacking kit with pull-out shelf:

approx. 172 cm

cDepth of the washer-dryer stack:

approx. 65 cm

Stacked units may not be installed

on pedestals.

Installation and connection

The Miele water protection

system

The Miele water protection system

protects the washer from water

damage.

The system consists of three main

components:

1) the inlet hose

2) the washer electronics and housing

3) the drain hose

1) The inlet hose

– Hose burst protection

The inlet hose can withstand

pressure of more than 7000 kPa.

2) The electronics and housing

– Sump

Any leaking water is collected in a

sump in the base of the washer. A

float then switches off the inlet

valves, preventing any additional

water inflow, and any water in the

suds container is pumped away.

–Overflow protection

This feature helps prevent the

washer from taking in too much

water. If the water exceeds a certain

level, the drain pump starts and

pumps away the water.

3) The drain hose

The drain hose is equipped with a

ventilation system that prevents the

washer from being emptied

accidentally.

Connecting to the water

supply

The washer is designed to comply with

applicable CSA standards, for

connection to a tap water line. It does

not require a non-return valve.

The flow pressure must be between

100 kPa and 1000 kPa. If the pressure

is above 1000 kPa, a

pressure-reducing valve MUST be

installed.

Two stopcocks with3/4" thread are

required for connecting to the water

supply. If these are not available, you

will need to have a qualified plumber fit

the washer to the water supply.

,The screw fittings are under

pressure from the water line. To

check that the connections are

watertight, slowly open the taps.

Correct the placement of the washer

and union as needed.

Maintenance and care

If the hose ever needs to be replaced,

use only a genuine Miele hose - it is

tested to withstand pressure of at least

7000 kPa.

In order to protect the water inlet

valve, the two dirt filter screens (one

in the open end of the inlet hose, the

other in the inlet point in the washer)

should not be removed.

Optional extension hose

Longer hoses 2.5 or 4.0 m in length are

available from your Miele dealer or

Miele Customer Service.

Installation and connection

This washer uses hot and cold

household water.

The washer must always be

connected to a tap water line (cold

water, inlet hose with blue tag).

Tap water line (cold water)

The tap water connection is established

using the inlet hose with the blue

marking.

If the washer is connected to this line

only, the appliance will need to be

re-programmed to cold water fill only.

Please contact your Miele dealer or

Miele Customer Service for

reprogramming instructions.

The second unused inlet hose, with the

red tag, will be attached to the rear of

the washer after re-programming.

Hot water connection

The hot water connection is established

using the inlet hose with the red

marking.

Tips for the hot water connection

–The hot water temperature at the

stopcock must not exceed 60°C, and

the ideal temperature is 55°C.

–If the hot water inlet is closed, the

washer will automatically switch over

to tap water mode after a period of

time. This safety feature is not

intended for long-term use. The

washer will continue to wash in hot

water mode, which can lead to a

poor wash result.

Installation and connection

Other manuals for W 1753

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual