Miele PW 6207D User manual

06.15 M.-Nr. 10 303 290 / 01

Installation plan

Washer-extractor

PW 6207 D

en - GB

M.-Nr. 10 303 290 / 01

Technisches Datenblatt / Technical datasheet: PW 6207 D

Datum / Date: 24.04.2013 Seite / Page: 7

Technical datasheet

Washer-extractor:

Heating type:

PW 6207

Steam (D)

Legend:

Circled, bold-type abbreviations:

Connection required

en - GB

Abbreviations surrounded by broken circle:

Connection optional or required, depending on model

Options / Accessories:

Miele plinth

UO 6020 (UO = open plinth)

Height

240

Width

900

Depth

1009

UG 6020 (UG = Box plinth)

Height

240

Width

920

Depth

1019

Concrete platform

Recommended height

240

Minimum height

100

Plinth width min.

920

Min. plinth depth

1050

DAV

Steam

connection valve

The steam connection valve to regulate the steam supply

must be provided on site.

The following valves can be ordered separately as electric

steam valves or as pneumatic steam valves.

Electric steam valve (ELD 01)

Regulatable steam pressure

kPa

200 - 1000

Connection gauge

Inch

½“

Voltage

1N AC 230

Frequency

50 - 60

Pneumatic steam valve (PND)

Regulatable steam pressure

kPa

0 - 1000

Connection gauge

Inch

½"

Supply point and pneumatic valve controls must be provided

on site.

Technisches Datenblatt / Technical datasheet: PW 6207 D

Datum / Date: 24.04.2013 Seite / Page: 8

Machine connections:

Electrical

connection

1. Standard voltage (standard version)

3N AC 380 - 415

Frequency

50 - 60

Connected load

4.3

Fuse rating

3 × 16

Connection cable, min. gauge

mm²

5 × 1.5

Connection cable not supplied (to be ordered

separately)

Variations in the following countries:

1. Standard voltage (standard version)

3 AC 220 - 240

Frequency

Connected load

4.3

Fuse rating

3 × 15

Connection cable, min. gauge

mm²

4 × 1.5

Connection cable not supplied (to be ordered

separately)

Alternative voltage (convertible)

3 AC 208

Frequency

Connected load

4.3

Fuse rating

3 × 15

Connection cable, min. gauge

mm²

4 × 1.5

Connection cable not supplied (to be ordered

separately)

The electrical connection may only be made to an electrical

system provided in accordance with all appropriate local and

national legislation and regulations. In addition, all regulations

of the appropriate utility supply companies and standards

relating to safety, and all applicable valid regulations and

technical standards must be complied with!

Electrical connection is the responsibility of a qualified

electrician.

The machine can be either hard-wired or connected via a

socket in compliance with IEC 60309-1. Wall socket or mains

isolator must be accessible after installation.

It is always recommended to make electrical connection via a

plug and socket so that electrical safety checks, e.g. during

repair or service work, can be carried out easily.

If it is necessary to install a residual current device (RCD) in

accordance with the local regulations, a residual current

device type B must be used.

Equipotential

bonding

Connection with male thread

10 × 35

for washers and nuts

Fasteners such as washers and nuts are not provided.

If necessary, equipotential bonding with good galvanic

contact must be guaranteed in compliance with all applicable

local and national installation codes.

Steam

connection

Steam pressure (Low pressure steam)

kPa

50

Direct

Boiling point

°C

120

Mass flow (max. delivery)

kg/h

Heater rating

Steam pressure (high-pressure steam)

kPa

50 - 400

Boiling point

°C

152

Mass flow (max. delivery)

kg/h

Heater rating

On-site threaded union

Inch

½" female thread

Steam valve, filter, non-return valve and steam shut-off valve

must be provided on site.

The steam valve should be installed in such a way as to

prevent any wash liquor from the machine from flowing back

into the valve.

Technisches Datenblatt / Technical datasheet: PW 6207 D

Datum / Date: 24.04.2013 Seite / Page: 9

Steam

connection

Steam pressure

kPa

600 - 1000

Indirect

Boiling point

°C

152 - 184

Mass flow (max. delivery)

kg/h

Heater rating

On-site threaded union

Inch

½" female thread

Steam valve, filter, non-return valve and steam shut-off valve

must be provided on site.

Steam valve supply lead length

500

The supply lead for the electric steam valve is included.

The steam valve should be installed close to the steam

connection.

Installation instructions for steam-heated washer-extractors

apply throughout.

Condensate

connection

On-site threaded union

Inch

½" female thread

A shut-off device and condensate trap must be provided on

site.

The condensate separator must be installed such that when

the system is not operating, the heater bank is completely

emptied. This means that no condensate may remain in the

heater bank. The use of an inverted bucket condensate trap

is recommended.

Cold water

(softened water)

Min. water pressure/flow pressure

kPa

100

Max. water pressure/flow pressure

kPa

1000

Flow rate, max.

l/min

Max. throughput (if hot and raw water supply is not available)

l/min

2 connection hoses with ¾" threaded union incl. Y-piece (¾" /

1") supplied.

On-site threaded union in accordance with DIN 44991 (flat

sealing)

Inch

1" male thread

Connection hose length

1500

Average water requirements for a standard 60°C Cottons

programme calculated using cold, hot and hard water

supplies.

l/h

approx. 124

In the absence of a hot water supply, add sufficient water to

reach the required amount.

If connecting to raw water, subtract water requirement from

cold water.

Hot water

(softened water)

Max. water intake temperature

°C

Min. water pressure/flow pressure

kPa

100

Max. water pressure/flow pressure

kPa

1000

Max. flow rate

l/min

1 inlet hose with ¾" threaded union provided.

On-site threaded union in accordance with DIN 44991 (flat

sealing)

Inch

¾" male thread

Connection hose length

1500

Average water requirements for a standard 60°C Cottons

programme calculated using cold, hot and hard water

supplies.

l/h

Approx. 108

If no hot water supply available, connect hot water hose to

cold water supply!

Cold water

Raw water

Min. water pressure/flow pressure

kPa

100

Max. water pressure/flow pressure

kPa

1000

Flow rate, max.

l/min

2 connection hoses with ¾" threaded union including Y-piece

(¾" / 1") included in optional kit.

On-site threaded union in accordance with DIN 44991 (flat

sealing)

Inch

1" male thread

Connection hose length

1500

Average water consumption in standard programme (60°

Cottons) when connected to cold, hot and raw water supplies.

l/h

Technisches Datenblatt / Technical datasheet: PW 6207 D

Datum / Date: 24.04.2013 Seite / Page: 10

Cold water

Liquid dispensing

Min. water pressure/flow pressure

kPa

100

Max. water pressure/flow pressure

kPa

1000

Flow rate, max.

l/min

5.5

1 supply hose with ¾" threaded union included in optional kit.

On-site threaded union in accordance with DIN 44991 (flat

sealing)

Inch

¾" male thread

Connection hose length

1500

Waste water

Drain valve

Max. water temperature

°C

Machine-side drain connection (ext. diameter)

75 [DN 70]

On-site drain connection (int. diameter)

75 [DN 70

connection]

Max. transient flow rate

l/min

200

Vented collector line required; if insufficient venting, use Miele

installation kit, Mat. no. 05238090.

When several machines are connected, ensure that the

manifold is of a sufficient diameter.

Securing of

machine

Without plinth

The machine must be adequately anchored to the floor!

Fastening material included with unit:

2 × angled brackets (from transport strut)

2 × wood screws DIN 571 (Ø × length)

8 x 80

2 × wall plugs (Ø × length)

12 x 60

The installation surface must be sufficiently stable and solid.

The fastening material provided is designed for securing the

machine to a concrete floor only. Fasteners for other floor

types must be provided on site.

On concrete plinth

The machine must be adequately anchored to the floor!

Fastening material included with unit:

2 × angled brackets (from transport strut)

2 × wood screws DIN 571 (Ø × length)

8 x 80

2 × wall plugs (Ø × length)

12 x 60

The quality of the concrete and its strength must be assessed

according to the machine load. A secure joint between a

concrete plinth and the floor must be guaranteed.

Miele plinth

A plinth must be securely bolted to the floor!

Fasteners included with plinth

4 × wood screws DIN 571 (Ø × length)

8 x 80

4 × rawl plugs (Ø × length)

12 x 60

Installation of machine and plinth must be in accordance with

the installation instructions provided.

This manual suits for next models

Table of contents

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Finlux

Finlux FLX108CF220 user manual

Whirlpool

Whirlpool 3LBR5132AN0 Use and care guide

Beko

Beko WKB 51231 PTMA manual