Miele DA 3460 User manual
Installation Instructions
DA3460, DA3480, DA3490 en - CA
Installation, repair and maintenance work should be performed by
a Miele authorized service technician in accordance with national
and local safety regulations and the provided installation instructions.
Disposal of packing material
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
,DANGER
Ensure that any plastic wrappings,
bags, etc., are disposed of safely
and kept out of the reach of babies
and young children. Danger of
suffocation!
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling center about the
possibility of recycling these materials.
Before discarding an old appliance,
disconnect it from the electrical
supply and cut off the power cord to
prevent it from becoming a hazard.
Caring for the environment
19
Appliance dimensions
20
* The hood can also be installed in a 23 5/8" (60 cm) cabinet.
Appliance dimensions
21
* The hood can also be installed in a 23 5/8" (60 cm) cabinet.
Appliance dimensions
22
1) Air extraction mode; consider accessories when measuring cabinet height and
cut-outs (e.g. muffler).
2) Recirculation mode with Installation kit DUU 151
Distance between cooktop and hood (S)
Do not install this exhaust hood over cooktops burning solid fuel.
Provided a larger distance is not given by the manufacturer of the cooktop,
follow the minimum safety distances between a cooktop and the bottom of the
hood:
Miele Cooktops Non-Miele
Cooktops
Electric Cooktops 24" (610 mm)
Electric Barbeques and Fryers 26" (660 mm)
Multiburner Gas cooktops
<43,000 BTU (12.6 KW)
and no burner > 15,000 BTU (4.5 KW)
26" (660 mm) 30" (760 mm)
Single burner (Wok) < 20,500 BTU (6 KW) 26" (660 mm) 30" (760 mm)
All other gas cooktops 30" (760 mm)
– If several gas surfaces are installed under the hood, the total output must be
considered when determining the minimum safety distance.
– If installing the exhaust hood in an overhead cabinet or if using a front panel
made of wood or plastic, observe the instructions of the manufacturer of the
gas cooktop regarding the use of flammable materials above the cooktop. If not
otherwise specified in the instructions, ensure a distance of at least 30”
(760 mm) from the gas cooktop.
–If local building codes require a greater safety distance, follow their requirement.
– If there is more than one appliance beneath the hood and they have different
minimum safety distances always select the greater distance.
See "Important Safety Instructions" for further information.
Appliance dimensions
23
Installation accessories
Installation
24
a2 runners
(1 x right, 1x left) to support the hood
in the cabinet.
b1 spacer strip
to conceal the gap between the rear
of the appliance and the wall.
cInstallation kit for recirculation
mode; contains air outlet grille, hose
and hose clips
(optional accessory)
dInstallation kit DML 400 to install a
custom panel
contains retractable brackets and
screws (optional accessory)
,CAUTION
To avoid risk of hand or other injury,
avoid contact with sharp edges
during the assembly and installation
process.
8 screws4x15mm
to anchor the ventilation hood in the
cabinet.
8 screws M4 x 12 mm
to anchor the ventilation hood at the
runners.
4 screws could be used (alternatively to
the plastic rivet) to fix the spacer bar.
2 screws4x15mm
to anchor the ventilation hood at rear
wall.
4 plastic rivets
to connect the space bar with the
appliance rear wall.
Installation
25
Installation
26
1. Installing the space bar
T=K cabinet depth minus G hood
depth
^The hood depth Gdepends on the
custom panel:
–aHood installed without front panel
–bHood installed with a cabinet
matching custom panel
These measures are only valid for the
installation if the front panel sits flush
with the cabinet corpus (without the
door).
If the front panel should be installed
recessed or flush with the cabinet door,
adjust the measure Taccordingly.
^Cut the supplied space bar to
measure T.
Clip it with a knife at the predeter-
mined breaking point of the next
lower measure.
^Screw the space bar flush with the
wall under the cabinet side walls.
^At the front edge of the spacer strip
draw a vertical line on left and right
side of the inside cabinet.
Installation
27
Other manuals for DA 3460
1
This manual suits for next models
2
Table of contents
Other Miele Ventilation Hood manuals
Miele
Miele DA 6498 W EXT User manual
Miele
Miele DA 5100 D User manual
Miele
Miele DA 6690 W User manual
Miele
Miele DAS 4630 User manual
Miele
Miele DA 6290 D User manual
Miele
Miele DA 424 V EXT User manual
Miele
Miele DA 292 i User manual
Miele
Miele DA 5100 D User manual
Miele
Miele DA 6698 W User manual
Miele
Miele DA 2900 EXT User manual
Miele
Miele DA 4208V D User manual
Miele
Miele DA 6996 W User manual
Miele
Miele AB 45 User manual
Miele
Miele DA2210 User manual
Miele
Miele DA 5100 D User manual
Miele
Miele DA 1160 User manual
Miele
Miele downdraft extractor User manual
Miele
Miele DA 422-4 Specification sheet
Miele
Miele DA 289-4 User manual
Miele
Miele DA 289 User manual
