Miele KM6357 User manual

Installation Instructions

KM 6357, KM 6386 en - CA

Installation, repair and maintenance work should be performed by

a Miele authorized service technician in accordance with national

and local safety regulations and the provided installation instructions.

The appliance must be installed by

a qualified professional and

connected to the electric power

supply by a qualified electrician.

The cabinet and the hood above the

cooktop must be installed before the

cooktop to avoid damaging it.

~The countertop must be

heat-resistant (up to 100°C), so that it

does not become deformed or the

veneer detached.

The wall strips must be heat-resistant

as well.

The cooktop must not be installed

above refrigerators/freezers,

dishwashers or washer/dryers.

~This cooktop must not be installed

above a stove or oven unless they have

a built-in cooling fan.

~Ensure that the connection cable

cannot be touched nor be subject to

any mechanical strain after the cooktop

has been installed.

All measurements are given in mm.

Safety instructions for installation

Safety clearance above the cooktop

For an exhaust hood above the

cooktop, always use the clearance

specified by the hood manufacturer.

If there are no specifications from the

hood manufacturer or if flammable

materials (e.g. a utensil rail) are

installed above the cooktop, the

clearance must be at least 760 mm.

If there is more than one appliance

installed below the exhaust hood,

each with a different safety

clearance, the largest clearance

must be used.

Safety clearances

Safety clearances to the sides and

back of the cooktop

There may be a cabinet or a room wall

of any height at the rear and on one

side (right or left) of the cooktop (see

illustrations).

a50 mm minimum distance between

the back of the countertop cut-out

and the rear edge of the countertop.

b50 mm minimum distance between

the right of the countertop cut-out

and the nearest piece of furniture

(e.g. a tall cupboard) or a wall.

c50 mm minimum distance between

the left of the countertop cut-out

and the nearest piece of furniture

(e.g. a tall cupboard) or a wall.

Not permitted!

Highly recommended!

Not recommended!

Safety clearances

Minimum clearance underneath the

cooktop

To ensure proper ventilation of the

cooktop, a minimum clearance is

required between the appliance and an

oven, protective base, or drawer.

The minimum clearance from the

bottom of the cooktop to

– the top of the oven must be 15 mm.

– the top of the protective base must

be 15 mm.

– bottom of the drawer must be 75

mm.

Protective base

Installation of a protective base under

the cooktop is allowed but not required.

A gap of 10 mm at the back is required

for the power supply cable.

For better cooling of the cooktop, we

recommend a gap of 20 mm at the

front.

Safety clearances

Safety clearance to a wall covering

A safety clearance must be maintained between the countertop cut-out and any

wall covering to protect it from heat damage.

If the covering is made of a combustible material (e.g. wood), a safety clearance

eof 50 mm must be maintained between the cut-out and the covering.

If the covering is made of a non-combustible material (e.g. metal, natural stone,

ceramic tiles), a minimum safety clearance eof 50 mm less the thickness of the

covering must be maintained between the cut-out and the covering.

Example: 15 mm wall covering

50 mm - 15 mm = 35 mm minimum clearance

Flush-fitted cooktops Cooktops with frame or bevelled edges

aMasonry

bWall covering

Dimension X = thickness of wall covering

cCountertop

dCut-out in the countertop

dMinimum safety clearance

for combustible materials is 50 mm

for non-combustible materials is 50 mm less dimension X

Safety clearances

Seal between cooktop and

countertop

The cooktop must not be sealed

with joint sealant. Cooktop and

countertop could get damaged if the

cooktop needs to be removed. Do

not use a joint sealant between

cooktop and countertop.

The seal under the edge of the upper

part of the cooktop provides an

adequate seal against the countertop.

Tiled countertop

The grouting aand the hatched area

below the cooktop frame must be

smooth and flat, so that the frame will

be level and the seal under the edge of

the upper part of the cooktop can

provide a seal against the countertop.

Instructions for installation

KM 6357

aFront

bCasing depth

cConnection for Miele|home

dMains connection box

The mains connection cable (1440 mm long) is supplied separately.

Building-in dimensions

KM 6386

aFront

bCasing depth

cConnection for Miele|home

dMains connection box

The mains connection cable (1440 mm long) is supplied separately.

Building-in dimensions

,CAUTION: Before installation or

servicing, disconnect the power

supply by either removing the fuses,

shutting off the power main or

manually "tripping" the circuit

breakers.

Installation work and repairs should

only be performed by a qualified

technician in accordance with all

applicable codes and standards.

Repairs and service by unqualified

persons could be dangerous and

the manufacturer will not be held

responsible.

Before connecting the appliance to

the power supply, make sure that

the voltage and frequency listed on

the data plate correspond with the

household electrical supply. This

data must correspond to prevent

appliance damage. Consult an

electrician if in doubt.

Only operate the cooktop after it has

been installed into the countertop.

Installer:

Please leave these instructions with

the consumer.

Power supply

^Make sure your electrical supply

matches the data plate.

Connection

The cooktop is ready for connection to

a grounded power supply.

KM 6357

208/240 V, 60 Hz, 40 A fuse rating

KM 6386:

208/240 V, 60 Hz, 50 A fuse rating

Connect as following:

Black wire: connect to L1 (hot)

Red wire: connect to L2 (hot)

Green wire: connect to GND (ground)

A dedicated line and junction box

should be used to connect the

KM 6357 to a 40 A circuit and the

KM 6386 to a 50 A circuit.

For further information, see the wiring

diagram provided with the appliance.

,WARNING:

THIS APPLIANCE MUST BE

GROUNDED!

Connecting the electrical supply

cable

The electric power supply cable

must be connected to the cooktop

by a qualified electrician.

Electrical connection

Other manuals for KM6357

This manual suits for next models

Table of contents

Popular Cooktop manuals by other brands

Bonnet

Bonnet OPTIMUM 700 Technical instructions

Jenn-Air

Jenn-Air JGCP430 installation instructions

Frigidaire

Frigidaire FES367FCC Wiring diagram

Ztove

Ztove EZ2 DUO instruction manual

Kleenmaid

Kleenmaid cooking GCTK9011 Instructions for use and warranty details

Casselin

Casselin CSASRE24 manual

Jenn-Air

Jenn-Air JGC2536EB00 Use & care guide

Waldorf

Waldorf RN8603E-B Technical data sheet

Whirlpool

Whirlpool SMP658CNEIXL quick guide

Wolf

Wolf CI243C/B Use and care guide

Fulgor Milano

Fulgor Milano F5PGK305S1 installation instructions

GE JP389 Specifications

Wells

Wells WV-2HFG owner's manual

IKEA

IKEA Lagan HGA4K user manual

Samsung

Samsung NA36N9755 installation manual

Lacor

Lacor 69562 Instructions for use and maintenance

Keating Of Chicago

Keating Of Chicago MG-2 manual

Jenn-Air

Jenn-Air CCE1400 Use and care guide